In the present paper, the design and optimization of a high frequency excitation source is presented. The device was developed for a harmonic response analysis test bench, aimed at dynamic characterization and resonance prediction of mechanical structures. A wide frequency range must be covered, depending on the analyzed structure: the range 1–10 kHz was considered in the present work. The device was designed for a test bench aimed at investigating the vibrational response of centrifugal compressor bladed wheels. A really compact solution was needed since the final test bench provides one exciter for each blade (up to 20 devices on the circumference hoop). Both contact and contactless solutions were considered, but only the contact solution was found to fulfill all the specifications. Finally, different stinger solutions were proposed and compared in the paper. The investigated solutions were: a beam stinger (diameter 1 mm); a wire stinger (diameter 0.2 mm); and a ball stinger (diameter 3 mm) with two different support solutions. Experimental tests performed on a device prototype allowed to verify the specifications fulfillment and to choose the best stinger solution for the application.
BattiatoGFirroneCBerrutiT (2017) Forced response of rotating bladed disks: Blade tip-timing measurements. Mechanical Systems and Signal Processing85: 912–926. DOI:10.1016/j.ymssp.2016.09.019.
2.
BerrutiTFirroneCGolaM (2011) A test rig for noncontact traveling wave excitation of a bladed disk with underplatform dampers. Journal of Engineering for Gas Turbines and Power133(3): 032502, DOIi: 10.1115/1.4002100.
3.
Berruti T and Maschio V (2012) Experimental investigation on the forced response of a dummy counter-rotating turbine stage with friction damping. Journal of Engineering for Gas Turbines and Power 134(122502): 1–8. DOI: 10.1115/1.4007325.
4.
Bertini L, Monelli B, Neri P, et al. (2014a) Robot assisted modal analysis on a stationary bladed wheel. In: Proceedings of ASME 2014 12th Biennial Conference on Engineering Systems Design and Analysis (ESDA), Copenhagen, Denmark. pp.1–8.
5.
Bertini L, Neri P, Santus C, et al. (2014b) Analytical investigation of the safe diagram for bladed wheels, numerical and experimental validation. Journal of Sound and Vibration 333(19): 4771–4788.
6.
Bertini L, Neri P and Santus C (2015) Design and optimization of a compact high-frequency electromagnetic shaker. In: Proceedings of 11th International Conference on Engineering Vibration, ICoEV 2015, Ljubljana, Slovenia, 7–10 September. pp.1–9.
7.
Bertini L, Neri P, Santus C, et al. (2016) Automated experimental modal analysis of bladed wheels with an anthropomorphic robotic station. Experimental Mechanics 57(2): 1–13.
8.
Bertini L, Neri P, Santus C, et al. (2017) One exciter per sector test bench for bladed wheels harmonic response analysis. In: Proceedings of the ASME 2017 Turbomachinery Technical Conference & Exposition, pp.1–9.
9.
Bidaut Y and Baumann U (2012) Identification of eigenmodes and determination of the dynamical behavior of open impellers. In: Proceedings of ASME Turbo Expo, Parts A and B, Copenhagen, Denmark, pp.1063–1073.
10.
EwinsD (2000) Modal Testing: Theory, Practice and Application, 2nd edition. Baldock, UK: Research Studies Press Ltd/Wiley.
11.
FirroneCBerrutiT (2012) An electromagnetic system for the non-contact excitation of bladed disks. Experimental Mechanics52(5): 447–459.
12.
Firrone C, Berruti T and Gola M (2013) On force control of an engine order-type excitation applied to a bladed disk with underplatform dampers. Journal of Vibration and Acoustics 135(4): 1–9.
13.
Furlani E (2001) Permanent Magnet and Electromechanical Devices. London, UK: Academic Press/Elsevier.
14.
JonesKCrossC (2003) Traveling wave excitation system for bladed disks. Journal of Propulsion and Power19(1): 135–141.
15.
KammererAAbhariR (2009) Experimental study on impeller blade vibration during resonance – Part I: Blade vibration due to inlet flow distortion. Journal of Engineering for Gas Turbines and Power131(2): art. no. 022508, DOI: 10.1115/1.2968869.
MartarelliMCastelliniPSantoliniCet al.(2011) Laser doppler vibrometry on rotating structures in coast-down: resonance frequencies and operational deflection shape characterization. Measurement Science and Technology22: 1–16. DOI:10.1088/0957-0233/22/11/115106.
18.
Mukhopadhyay N, Chowdhury SG, Das G, et al. (1998) An investigation of the failure of low pressure steam turbine blades. Engineering Failure Analysis 5(3): 181–193.
19.
Neri P (2013) Studio della forza di interazione tra campo magnetico e bersaglio ferromagnetico mediante prove sperimentali e modelli analitici e numerici [Study of the interaction strength between magnetic field and ferromagnetic performance by experimental tests and analytical and numerical models]. In: Proceedings of the 42th Convegno Nazionale AIAS, pp.1–10. [In Italian.].
20.
NeriP (2017) Bladed wheels damage detection through non-harmonic Fourier analysis improved algorithm. Mechanical Systems and Signal Processing88: 1–8. DOI: 10.1016/j.ymssp.2016.11.010.
21.
NeriP (submitted) Interaction force between magnetic field and ferromagnetic target: Analytical, numerical and experimental study. Applied and Computational Mechanics.
22.
NeriPPeetersB (2015) Non-harmonic Fourier analysis for bladed wheels damage detection. Journal of Sound and Vibration356: 181–194.
23.
Oberholster A and Heyns P (2009) Online condition monitoring of axial-flow turbomachinery blades using rotor-axial eulerian laser doppler vibrometry. Mechanical Systems and Signal Processing 23(5): 1634–1643.
24.
Pesek L, Vanek F, Bula V, et al. (2011) Excitation of blade vibration under rotation by synchronous electromagnet. Engineering Mechanics 18(3/4): 249–257.
25.
RavaudRLemarquandGBabicSet al.(2010) Cylindrical magnets and coils: Fields, forces, and inductances. IEEE Transactions on Magnetics46(9): 3585–3590.
26.
Rieger N (1990) The high cost of failure of rotating equipment. In: Proceedings of the 44th Meeting of the Mechanical Failures Prevention Group, pp.1–17.
27.
RobertsonWCazzolatoBZanderA (2011) A simplified force equation for coaxial cylindrical magnets and thin coils. IEEE Transactions on Magnetics47(8): 2045–2049.
28.
RobertsonWCazzolatoBZanderA (2012) Axial force between a thick coil and a cylindrical permanent magnet: Optimizing the geometry of an electromagnetic actuator. IEEE Transactions on Magnetics48(9): 2479–2487.
29.
SinghMVargoJ (1989) Reliability evaluation of shrouded blading using the SAFE interference diagram. Journal of Engineering for Gas Turbines and Power111(4): 601–609.
30.
Singh M, Matthews T and Ramsey C (1994) Fatigue damage of steam turbine blade caused by frequency shift due to solid buildup – A case study. In: Proceedings of the 23rd Turbomachinery Symposium, pp.107–114. Available at: http://turbolab.tamu.edu/proc/turboproc/T23/T2391-105.pdf.
