In this paper, the influence of clutch disk pre-damper mechanism constituents on the idle rattle phenomenon was investigated with an analytical model containing a new time-varying gear mesh stiffness function. Comparing experimental results to simulation results for the same excitation input was the key implementation for the validation of proposed model. The engine speed fluctuations represented in the simulation was imported from a speed measurement of a diesel engine in the test bench.
BarthodMHayneBTébecJLPinJC (2007) Experimental study of gear rattle excited by a multi-harmonic excitation. Applied Acoustics68: 1003–1025.
2.
BozcaM (2010) Torsional vibration model based optimization of gearbox geometric design parameters to reduce rattle noise in an automotive transmission. Mechanism and Machine Theory45: 1583–1598.
3.
BozcaMFietkauP (2010) Empirical model based optimization of gearbox geometric design parameters to reduce rattle noise in an automotive transmission. Mechanism and Machine Theory45: 1599–1612.
4.
BrancatiRRoccaERussoR (2005) A gear rattle model accounting for oil squeeze between the meshing gear teeth. Proceedings of Imech E-Part D. Journal of Automobile Engineering219: 1075–1083.
5.
BrancatiRRoccaERussoR (2007) An analysis of the automotive driveline dynamic behavior focusing on the influence of the oil squeeze effect on the idle rattle phenomenon. Journal of Sound and Vibration303: 858–872.
6.
BrancatiRRoccaERussoR (2009) Experimental investigations about the influence of oil lubricant between teeth on the gear rattle phenomenon. Journal of Sound and Vibration321: 647–661.
7.
CaiY (1995) Simulation on the rotational vibration of helical gears in consideration of the tooth separation phenomenon (a new stiffness function of helical involute tooth pair). Transactions of the ASME. Journal of Mechanical Design177: 460–469.
8.
De la CruzMTheodossiadesSRahnejatH (2010) An investigation of manual transmission drive rattle. Proceedings of the IMechE. Journal of Multibody Dynamics224: 167–181.
9.
DionJLMoyneSLChevallierGSebbahH (2009) Gear impacts and idle gear noise: Experimental study and non-linear dynamic model. Mechanical Systems and Signal Processing23: 2608–2628.
10.
Fidlin A and Seebacher R (2006) DMF simulations techniques – Finding the needle in the haystack. 8th LuK Symposium 55–71.
MichaelYWZhaoWRadhakrishnanM (2002) Numerical modeling and analysis of automotive transmission rattle. Journal of Vibration and Control8: 921–943.
15.
MiyasatoHHSimionattoVGSDias JuniorM (2011) Study of the gear rattle phenomena in automotive powertrain systems. 21st International Congress of Mechanical Engineering. 24–28.
16.
Reik W, Seebacher R and Kooy A (1998) Dual Mass Flywheel. 6th LuK Symposium. Baden-Baden, LuK Buhl, pp. 69–94.
17.
RoccaERussoR (2011) Theoretical and experimental investigation into the influence of the periodic backlash fluctuations on the gear rattle. Journal of Sound and Vibration330: 4738–4752.
18.
SinghRXieHComparinRJ (1989) Analysis of automotive neutral gear rattle. Journal of Sound and Vibration131: 177–196.
19.
TangasawiOTheodossiadesSRahnejatHKellyP (2008) Non-linear vibro-impact phenomenon belying transmission idle rattle. Proceedings of the IMechE, Journal of Mech. Engineering Science222: 1909–1923.
20.
TsujiuchiNKoizumiTHaraN (2012) The effects of clutch damper in idling driveline rattle, Doshisha University, Japan: Exedy Corporation, Department of Mechanical Engineering.
21.
UmezawaKSuzukiTSatoT (1986) Vibration of power transmission helical gears (approximate equation of tooth stiffness). Bulletin of JSME29: 1605–1611.
22.
WangYManojRZhaoWJ (2001) Gear rattle modeling and analysis for automotive manual transmissions. Proceedings of IMechE, Journal of Automobile Engineering215: 241–258.
23.
Yüceşan A (2014) Gearbox vibration isolation with clutch disk damper. Msc. Thesis, Yildiz Technical University, Turkey.
