A complete nonlinear finite element model for coupled-domain microelectromechanical system devices with electrostatic actuation and squeeze film effect was developed. for this purpose, a corotational finite element formulation for the dynamic analysis of planer Euler-Bernoulli microbeams considering geometrical nonlinearities due to both large structural deformation and electrostatic actuation is developed. In this method, the internal forces due to deformation and residual stresses, the elemental inertias, and the damping effect of the squeeze-film are systematically derived by consistent linearization of the fully geometrically nonlinear beam theory using d'Alembert and the virtual work principles. An incremental-iterative method based on the Newmark direct integration procedure and the Newton-Raphson algorithm is used to solve the nonlinear dynamic equilibrium equations. Several numerical examples are presented and their results are compared with those found experimentally, which indicate a very close agreement.
Abdel-Rahman, E.M., Younis, M.I., and Nayfeh, A.H., 2002, "Characterization of the mechanical behavior of an electrically actuated microbeam," Journal of Micromechanics and Microengineering12, 759-766.
2.
Ahn, Y., Guckel, H., and Zook, J.D., 2001, "Capacitive microbeam resonator design," Journal of Micromechanics and Microengineeering11, 70-80.
3.
Bao, M., Yang, H., Sun, Y., and Wang, Y., 2003, "Squeeze-film air damping of thick hole plate," Sensors and Actuators A: Physical, 108, 212-217.
4.
Bathe, K.J., 1995, Finite Element Procedures in Engineering Analysis, Prentice-Hall, New York.
5.
Belytschko, T. and Hsieh, B.J., 1973, "Nonlinear transient finite element analysis with convicted coordinates," International Journal for Numerical Methods in Engineering7, 255-271.
6.
Borhan, H. and Ahmadian, M.T., 2006, "Modeling of geometrically nonlinear electrostatically actuated microbeams," in Proceedings of the International MEMS Conference, Singapore, May 9-12.
7.
Borhan, H., Movahhedy, M.R., and Ahmadian, M.T., 2006, "Dynamic finite element modeling of coupled-domain MEMS devices with electrostatic and squeeze film effects," in Proceedings of the Third AUS International Symposium on Mechatronics (AUS-ISM06) , Sharjah, United Arab Emirates, April 18-20.
8.
Chowdhury, S., Ahmadi, M., and Miller, W.C., 2005, "A closed-form model for the pull-in voltage of electrostatically actuated cantilever beams," Journal of Micromechanics and Microengineering15, 756-763.
9.
Crisfield, M.A., 1997, Nonlinear Finite Element Analysis of Solids and Structures, Advanced Topics, Vol. 2, Wiley, Chichester, UK.
10.
Fang, W. and Wickert, J.A., 1996, "Determining mean and gradient residual stresses in thin films using micro machined cantilevers," Journal of Micromechanics and Microengineering6(3), 301-309.
11.
Felippa, C.A. and Haugen, B., 2005, "A unified formulations of small-strain corotational finite elements I. Theory," Computer Methods in Applied Mechanics and Engineering194, 2285-2335.
12.
Flores, G., Mercado, G.A., and Pelesko, J.A., 2003, "Dynamics and touchdown in electrostatic MEMS", in Proceedings of the IDETC/CIE, 19th ASME Biennial Conference on Mechanical Vibration and Noise, Chicago, IL, September 2-6.
13.
Gupta, R.K., Ostberg, P.M., and Senturia, S.D., 1996, "Material property measurement of micromechanical polysilicon beams," in SPIE Conference on Micromachining & Microfabrication, Austin, TX, October 14- 16.
14.
Horrigmoe, G. and Bergan, P.G., 1978, "Instability analysis of free-form shells by flat finite elements," Computer Methods in Applied Mechanics and Engineering16, 11-35.
15.
Hsiao, K.M. and Yang, J.Y., 1990, "Nonlinear dynamic analysis of elastic frames," Computers & Structures33, 1057-1063.
16.
Hsiao, K.M., Yang, R.T., and Lee, A.C., 1994, "A consistent finite element formulation for non-linear dynamic analysis of planar beam," International Journal of Numerical Methods in Engineering37, 75-89.
17.
Hu, Y.C., Chang, C.M., and Huang, S.C., 2004, "Some design considerations on electrostatically actuated microstructures," Journal of Sensors and Actuators: A. Physical , 112, 155-161.
18.
Huang, J.M., Liew, K.M., Wong, C.H., Rajendran, S., Tan, M.J., and Liu, A.Q., 2001, "Mechanical design and optimization of a capacitive micro machined switch," Journal of Sensors and Actuators: A. Physical93-3, 273-285.
19.
Hung, E.S. and Senturia, S.D., 1999, "Generating efficient dynamical models for microelectromechanical systems from few finite-element simulation runs," IEEE Journal of Microelectromechanical Systems8-3, 280-289.
20.
Ijntema, D.J. and Tilmans, H.A., 1992, "Static and dynamic aspects of an air-gap capacitor," Sensors and ActuatorsA35, 121-8.
21.
Jensen, B.D., DeBoer, M.P., and Miller, S.L., 1999, "IMaP: Interferometery for material property measurements in MEMS," in Proceedings of MSM'99, San Juan, Puerto Rico, April 19-21.
22.
Ko, W.H. and Wang, Q., 1999, "Touch mode capacitive pressure sensors," Journal of Sensors and Actuators75, 242-251.
23.
Krylov, V. and Maimon, R., 2004, "Pull-in dynamics of an elastic microstructure actuated by continuously distributed electrostatic force," ASME Journal126, 332-342.
24.
Liang, Y.C., Lin, W.Z., Lee, H., Lim, S.P., Lee, K.H., and Feng, D.P., 2001, "A neural-network-based method of model reduction for the dynamic simulation of MEMS," Journal of Micromechanics and Microengineering11, 226-233.
25.
Lishchynska, M., Cordero, N., Slattery, O., and Mahony, C.O., 2005, "Modeling electrostatic behavior of micro cantilevers incorporating residual stress gradient and non-ideal anchors", Journal of Micromechanics and Microengineering. 15, S10-S14.
26.
Mahony, C.O., Hill M., Duane, R., and Mathewson A., 2003, "Analysis of electromechanical boundary effects on the pull-in of micro machined fixed-fixed beams," Journal of Micromechanics and Microengineering13, S75-S80.
27.
McCarthy, B., Adams, G., McGruer, N., and Potter, D., 2002, "A dynamic model including contact bounce, of an electrostatically actuated micro-switch," Journal of Microelectromechanical Systems11, 276-283.
28.
Nayfeh, A.H. and Younis, M.I., 2004, "A new approach to the modeling and simulation of flexible microstructures under the effect of squeeze-film damping," Journal of Micromechanics and Microengineering14, 170-181.
29.
Nayfeh, A.H., Younis, M.I., and Abdel-Rahman, E.M. , 2005, "A reduced-order models for MEMS applications," Nonlinear Dynamics41, 211-236.
30.
Nayfeh, A.H., Younis M. I., and Abdel-Rahman, E.M., 2007, "Dynamic pull-in phenomenon in MEMS resonators," Nonlinear Dynamics48, 153-163.
31.
Nour-Omid, B. and Rankin, C.C., 1991, "Finite rotation analysis and consistent linearization using projectors," Computer Methods in Applied Mechanics and Engineering93, 353-384.
32.
Nygard, M.K. and Bergan, P.G., 1984, "Advances in treating large rotations for nonlinear problems" in State-of-the-Art Surveys on Computational Mechanics, J. Tinsley Oden, ed., Asme, New York, 305-332.
33.
Olszewski, Z., Hill, M., O'Mahony, C., Duane, R., and Houlihan, R., 2005, "Characterization, modeling and performance evaluation of CMOS integrated multielectrode tunable capacitor (MTC)," Journal of Micromechanics and Microengineering15, S122-S131.
34.
Osterberg, P.M., 1995, "Electrostatically actuated micro-electro-mechanical test structures for material property measurement," PhD thesis, MIT, September.
35.
Ozdoganlar, O.B., Hansche, B.D., and Carne, T.G., 2003, "Experimental modal analysis for microelectromechanical systems," Journal of Experimental Mechanics45, 498-506.
36.
Pamidighantam, S., Puers, R., Baert, K., and Tilmans, H.A.C., 2002, "Pull-in voltage analysis of electrostatically actuated beam structures with fixed-fixed and fixed-free end conditions," Journal of Micromechanics and Microengineering12, 458-464.
37.
Pruessner, M.W., King, T., Kelly, D., Grover, R., and Calhoun, L., 2003, "Mechanical property measurement of InP-based MEMS for optical communications," Journal of Sensors and Actuators105, 190-200.
Seshia, A.A., Palaniapan M., Roessig T.A., Howe R.T., Gooch R.W., Schimert T.R., and Montague, S., 2002, "A vacuum packaged surface micro machined resonant accelerometer ," Journal of Microelectromechanical Systems11,784-793.
40.
Tilmans, H.A. and Legtenberg, R., 1994, "Electrostatically driven vacuum-encapsulated polysilicon resonators: Part II," Theory and Performance Sensors and Actuators45, 67-84.
41.
Van der Meijs, N. and Fokkema, J.T., 1984, "VLSI circuit reconstruction from mask topology," Integration, the VLSI Journal2, 85-119.
42.
Wempner, G.A., 1969, "Finite elements, finite rotations and small strains of flexible shells," International Journal of Solids and Structures5, 117-153.
43.
Younis, M.I., Abdel-Rahman, E.M., and Nayfeh, A.H., 2003, "A reduced-order model for electrically actuated microbeam-based MEMS," Journal of Microelectromechanical Systems12, 672-680.
44.
Zook, J.D. and Burns, D.W., 1992, "Characteristics of polysilicon resonant microbeams," Sensors and Actuators35, 51-59.
Supplementary Material
Please find the following supplemental material available below.
For Open Access articles published under a Creative Commons License, all supplemental material carries the same license as the article it is associated with.
For non-Open Access articles published, all supplemental material carries a non-exclusive license, and permission requests for re-use of supplemental material or any part of supplemental material shall be sent directly to the copyright owner as specified in the copyright notice associated with the article.
