Sage Journals: Discover world-class research

Abstract

In this paper, a multi-objective optimization index is introduced for improving the dynamic behavior of an actuated structurally flexible arm through geometric shape design. The improvement in the dynamic behavior is achieved by defining a vector optimization cost function. This cost function is associated with the frequency of the lowest system zero when joint angles are taken as outputs, the gain sensitivity of open-loop system modes, and the gain sensitivity of the closed-loop system modes at its transmission zeros. Moreover, a general relationship is obtained between the system pole and zero locations. In particular, it is shown that the magnitude of each system zero is smaller than a corresponding flexural mode and thus the smallest zero always occurs before the smallest pole and should therefore be considered in structural shape design. The design method is applied for finding an optimized structural shape for a single-link flexible arm. The optimized link is shown to yield superior robustness and performance characteristics in a closed-loop system when compared to the non-optimized uniform link. Thus, simpler control schemes can be utilized for the optimized flexible-link system compared to the non-optimized case.

Get full access to this article

View all access options for this article.

References

Asada, H., Park, J. H., and Rai, S., 1991, “A control-configured flexible arm: Integrated structure/control design,” in IEEE International Conference on Robotics and Automation, Sacramento, CA.

Balas, M., 1978, “Active control of flexible systems,” Journal of Optimization Theory and Applications 25, 415-436 .

Book, W. J., 1984, “Recursive Lagrangian dynamics of flexible manipulator arms,” International Journal of Robotics Research 3, 87-101 .

Book, W.J. and Majette, M., 1983, “Controller design for flexible, distributed parameter mechanical arms via state space and frequency domain techniques,” Journal of Dynamic Systems, Measurement, and Control 105, 245-254 .

de Boor, C., 1978, A Practical Guide to Splines, Springer-Verlag, New York .

de Boor, C., 1990, Spline Toolbox for use with MATLAB, The MathWorks, Inc., Natick, MA .

Juang, J. N. and Horta, L. G., 1986, “A slewing control experiment for flexible structures,” Journal of Guidance, Control, and Dynamics 9, 599-607 .

Konno, A., Uchiyama, M., Kito, Y., and Murakami, M., 1994, “Vibration controllability of flexible manipulators,” in IEEE International Conference on Robotics and Automation, San Diego, CA.

Konno, A., Uchiyama, M., Kito, Y., and Murakami, M., 1997, “Vibration controllability of flexible-link manipulators,” International Journal of Robotics Research 16, 567-576 .

10.

Kreisselmeier, G. and Steinhauser, R., 1979, “Systematic control design by optimizing a vector performance index,” IFAC Symposium on Computer Aided Design of Control Systems, Zurich, Switzerland.

11.

Leo, D. J. and Inman, D. J., 1993a, “Modeling and control simulations of a slewing frame containing active members,” Smart Materials and Structures 2, 82-95 .

12.

Leo, D. J. and Inman, D. J., 1993b, “Pointing control and vibration suppression of a slewing flexible frame,” Journal of Guidance, Control, and Dynamics 17, 529-536 .

13.

Moallem, M., Khorasani, K., and Patel, R. V., 1997a, “An integral manifold approach for tip position tracking of flexible multi-link manipulators,” in IEEE Transactions on Robotics and Automation 13, 823-837 .

14.

Moallem, M., Patel, R., and Khorasani, K., 1997b, “An inverse dynamics control strategy for tip position tracking of flexible multi-link manipulators,” Journal of Robotic Systems 14, 649-658 .

15.

Moallem, M., Khorasani, K., and Patel, R., 1998, “Optimum structure design for improving the dynamics of flexible-link manipulators,” International Journal of Robotics and Automation 13, 125-131 .

16.

Nguyen, P. K., Ravindran, R., Carr, R., Gossain, D. M., and Doetsch, K. H., 1982, “Structural flexibility of the shuttle remote manipulator system mechanical arm,” AIAA Guidance and Control Conference, San Diego, CA, pp. 246-256 .

17.

Park, J. and Asada, H., 1992, “Integrated structure/control design of a two-link nonrigid robot arm for high speed positioning,” in IEEE International Conference on Robotics and Automation, Nice, France.

18.

Patel, R. V., Laub, A. J., and Van Duren, P. M., editors, 1994, Numerical Linear Algebra Techniques for Systems and Control, IEEE Press, New York .

19.

Redfern, D., 1993, The Maple Handbook, Springer-Verlag, New York .

20.

Tarokh, M., 1992, “Measures for controllability, observability, and fixed modes,” in IEEE Transactions on Automatic Control 37, 1268-1273 .

21.

Thomson, W., 1988, Theory of Vibrations with Applications, Prentice-Hall, Englewood Cliffs, NJ .

22.

Wang, F. and Russell, J., 1995, “Optimum shape construction of flexible manipulators with total weight constraint,” IEEE Transactions on Systems, Man and Cybernetics 25, 605-614 .

23.

Wilkinson, J., 1965, The Algebraic Eigenvalue Problem, Oxford University Press, Oxford .

24.

Williams, T., 1989, Transmission zero bounds for large space structures with applications , AIAA Journal of Guidance and Control 12, 33-38 .

Design of an Actuated Flexible Arm for Improved Vibration Properties

Abstract

Get full access to this article

References