The paper presents the procedure for determining the factor of safety (FoS) using the strength reduction method (SRM) for the case of a concrete damage plasticity constitutive model. The SRM was originally used in a slope stability analysis and in its original form, this method was applied by reducing the shear strength of the material. Since damage in concrete occurs due to exceeding the normal stresses in the principal directions, and not due to exceeding the shear strength, this method was modified and adapted to the concrete damage plasticity constitutive model. Instead of reducing the failure surface, the parameters which describe the mechanical behavior in the case of uniaxial compression and uniaxial tension were reduced. In this way, the reduction of stress and the corresponding strain was carried out in the entire range of total strain, without changing the shape of the failure surface in the deviator plane. For the proposed methodology, a numerical algorithm was developed and implemented into the software PAK. The algorithm was verified through test examples and the obtained results were compared with analytically calculated FoS. The excellent agreement is observed between the FoS obtained by applying the proposed algorithm and the analytically calculated FoS.
AbraOBen FtimaM (2020)
Development of a new design approach of reinforced concrete structures based on strength reduction method. Engineering Structures207: 110192.
2.
Bentley Systems International Limited (2019) Plaxis 2D Reference Manual.
Dublin:
Bentley Systems International Limited.
3.
BishopA W (1955)
The use of the slip circle in the stability analysis of slopes. Géotechnique5(1): 7–17.
4.
CaspeeleRSykoraMLorenzo AllaixD, et al. (2013)
The design value method and adjusted partial factor approach for existing structures. Structural Engineering International23(4): 386–393.
5.
ChengYLansivaaraTWeiW (2007)
Two-dimensional slope stability analysis by limit equilibrium and strength reduction methods. Computers and Geotechnics34(3): 137–150.
6.
CoutoDCarvalhoMCintraA, et al. (2015)
Concrete structures. Contribution to the safety assessment of existing structures. Revista Ibracon De Estruturas E Materiais8(3): 365–389.
7.
DawsonERothW (1999)
Slope stability analysis by strength. Géotechnique49(6): 835–840.
8.
FuWLiaoY (2010)
Non-linear shear strength reduction technique in slope stability calculation. Computers and Geotechnics37(3): 288–298.
9.
GriffithsD VLaneP A (1999)
Slope stability analysis by finite elements. Géotechnique49(3): 387–403.
10.
HammahRYacoubTCorkumB (2005) The Shear Strength Reduction Method for the Generalized Hoek-Brown Criterion.
Alaska, s.n:
Anchorage.
11.
JanbuN (1954) Application of Composite Slip Surface for Stability Analysis. In: Proceedings of European Conference on Stability of Earth Slopes, Sweden, pp. 43–49.
12.
KieferBWaffenschmidtTSpraveL, et al. (2018)
A gradient-enhanced damage model coupled to plasticity – multi-surface formulation and algorithmic concepts. International Journal of Damage Mechanics27(2): 253–295.
13.
KojićMBatheK-J (2005) Inelastic Analysis of Solids and Structures.
Berlin:
Springer.
14.
KojićMI and Drugi (2010) Software for geomechanics – PAK-GEO.,
Kragujevac:
Faculty of Mechanical Engineering, University of Kragujevac.
15.
KojićMSlavkovićRŽivkovićM, et al. (2011), PAK-S: Program for FE Structural Analysis.,
Kragujevac:
University of Kragujevac, Faculty of Engineering.
16.
LaraCTannerPZanuyC, et al. (2021)
Reliability verification of existing RC structures using partial factors approaches and site-specific data. Applied Sciences11(4): 1653.
17.
LeeJ (1996) Theory and Implementation of Plastic-Damage Model for Concrete Structures under Cyclic and Dynamic Loading.,
Berkeley:
University of California.
18.
LeeJFenvesG (1998)
Plastic-damage model for cyclic loading of concrete structures. Journal of Engineering Mechanics124(8): 892–900.
19.
LiLTangCZhuW, et al. (2009)
Numerical analysis of slope stability based on the gravity increase method. Computers and Geotechnics36(7): 1246–1258.
20.
LublinerJOliverJOllerS, et al. (1989)
A plastic-damage model for concrete. International Journal of Solids and Structures25(3): 299–326.
21.
ManzariM TNourM A (2000)
Significance of soil dilatancy in slope stability analysis. Journal of Geotechnical and Geoenvironmental Engineering126(1): 75–80.
22.
NaylorDJ (1982) Finite elements and slope stability. In: JB Martins (ed) Numerical Methods in Geomechanics. NATO Advanced Study Institutes Series, vol 92. Springer, Dordrecht. https://doi.org/10.1007/978-94-009-7895-9_10
23.
OmidiOLotfiV (2010)
Finite element analysis of concrete structures using plastic-damage model in 3-D implementation. International Journal of Civil Engineering8(3): 187–203.
24.
ParkTAhmedBVoyiadjisG Z (2022)
A review of continuum damage and plasticity in concrete: Part I – Theoretical framework. International Journal of Damage Mechanics31(6): 901–954.
25.
RakićD MBodićA SMilivojevićN J, et al. (2021)
Concrete damage plasticity material model parameters identification. Journal of the Serbian Society for Computational Mechanics15(2): 111–122.
26.
RakićDDunićVŽivkovićM, et al. (2019)
Modeling of damaged concrete using initial degradation parameter. Journal of the Serbian Society for Computational Mechanics13(2): 8–18.
27.
SarmaS K (1973)
Stability analysis of embankments and slopes. Géotechnique23(3): 423–433.
28.
SeoY K (1998) Computational Methods for Elastoplastic Slope Stability Analysis with Seepage.
USA:
The University of Iowa.
29.
SpencerE (1967)
A method of analysis of the stability of embankments assuming parallel inter-slice forces. Géotechnique17(1): 11–26.
30.
ŠumaracDSekulovićMKrajčinovićD (2003)
Fracture of reinforced concrete beams subjected to three point bending. International Journal of Damage Mechanics12(1): 31–44.
31.
VoyiadjisG ZAhmedBParkT (2022)
A review of continuum damage and plasticity in concrete: Part II – Numerical framework. International Journal of Damage Mechanics31(5): 762–794.
32.
Water institute Jaroslav Cerni (2019), Dam Safety Management System: Report on Analyzes Using FE Models of Thermal, Filtration and Stress-Strain Processes.
Belgrade:
Water institute Jaroslav Cerni.
33.
Water institute Jaroslav Cerni and Faculty of Engineering, University of Kragujevac (2017) Algorithm and Implementation of the Stress Integration Procedure for the Concrete Material Model with Damage, Verification Examples and Description of the Structure of the Input File for the PAK Program.
Belgrade:
Water institute Jaroslav Cerni.
34.
WolińskiS (2011)
Global safety factor for nonlinear design of concrete structures. Archives Of Civil EngineeringLVII(3): 331–339.
35.
XueHDangFYinX, et al. (2018)
Unified overload method of slope stability analysis based on potential sliding direction. KSCE Journal of Civil Engineering22(9): 3254–3262.
36.
ZhangP WChenZ Y (2004)
Finite element method for solving safety factor of slope stabilily. Rock and Soil Mechanics25(11): 1757–1760.
ZhengHSunGLiuD (2009)
A practical procedure for searching critical slip surfaces of slopes based on the strength reduction technique. Computers and Geotechnics36(1–2): 1–5.
39.
ZienkiewiczOHumphesonCLewisR (1975)
Associated and nonassociated viscoplasticity in soil mechanics. Géotechnique25(4): 671–689.
