Mechanical testing of thin films for MEMS has progressed from a developmental stage to a point where validated techniques are used to study the behavior of devices and materials at a very fine scale. Tensile data covering a range of sizes and test techniques have been analyzed to examine the distribution of defects that would be responsible for the observed fracture strengths. For each sample, a critical defect size was calculated based on a published fracture toughness and a half-circular surface crack fracture toughness model. For polysilicon produced using the SUMMiT V process in the period 1998-1999, the calculated mean defect size was 115 nm. For polysilicon produced using the MUMPS process, the calculated mean defect size was 389 nm.
Get full access to this article
View all access options for this article.
References
1.
Boyce, Brad. Unpublished Data, Based on Modifications to the Technique Reported in Ref 13 to Account for Errors Associated with the use of a Conical Tip.
2.
Chasiotis, Ioannis and Knauss, Wolfgang G. (2000). Microtensile Tests with the Aid of Probe Microscopy for the Study of MEMS Materials , In: Proc. of the Int. for Optical Engineering (SPIE), Vol. 4175, pp. 92-99 , Santa Clara, CA .
3.
Chasiotis, I. and Knauss, W.G. (2002). A New Microtensile Tester for the Study of MEMS Materials with the Aid of Atomic Force Microscopy , Experimental Mechanics, 42(1): 51-57 .
4.
Connally, J.A. and Brown, S. (12 June 1992). Slow Crack Growth in Single-crystal Silicon , Science, 256(5063): 1537-1539 .
5.
Greek, S. and Ericson, F. (1998). Young's Modulus, Yield Strength and Fracture Strength of Microelements Determined by Tensile Testing, Microelectromechanical Structures for Materials Research , MRS Proceeding v518 Warrendale, pp. 51-56 , PA.
6.
Kahn, H., Tayebi, N., Ballarini, R., Mullen, R.L. and Heuer, A.H. (2000). Fracture Toughness of Polysilicon MEMS Devices , Sensors and Actuators, 82: 274-280 .
7.
Koskinen, J., Steinwall, J.E., Soave, R. and Johnson, H.H. (March 1993). Microtensile Testing of Free-standing Polysilicon Fibers of Various Grain Sizes , Journal of Micromechanics & Microengineering, 3(1): 13-17 .
8.
LaVan, D.A., Jackson, K., Glass, S.J., Friedmann, T.A., Sullivan, J.P. and Buchheit, T. (2001b). Direct Tension and Fracture Toughness Testing Using the Lateral Force Capabilities of a Nanomechanical Test System, In: Muhlstein, C. and Brown, S.B. (eds), Mechanical Properties of Structural Films, ASTM STP 1413, American Society for Testing and Materials, West Conshohocken, PA .
9.
LaVan, D.A., Tsuchiya, T., Coles, G., Knauss, W.G., Chasiotis, I. and Read, D. (2001a). Cross Comparison of Direct Strength Testing Techniques on Polysilicon Films, In: Muhlstein, C. and Brown, S.B. (eds), Mechanical Properties of Structural Films, ASTM STP 1413, American Society for Testing and Materials, West Conshohocken, PA .
10.
Newman, J.C. and Raju, I.S. (1986). Stress-Intensity Factor Equations for Cracks in Three-dimensional Finite Bodies Subjected to Tension and Bending Loads, In: Atluri, S.N. (ed.), Computational Methods in the Mechanics of Fracture, Elsevier North Holland, New York .
11.
Read, D.T. and Marshall, J.C. (1996). Measurements of Fracture Strength and Young's Modulus of Surface-micromachined Polysilicon , In: SPIE Proceedings, 2880: 56-63 .
12.
Read, D.T., McColskey, J.D. and Cheng, Y.-W. (2001). New Microscale Test Technique for Thin Films , In: SEM Annual Conference Proceedings, to be published in June.
13.
Sharpe, W.N. Jr., Brown, S., Johnson, G.C. and Knauss, W. (1998). Round-robin Tests of Modulus and Strength of Polysilicon, Microelectromechanical Structures for Materials Research , MRS Proceeding v518 Warrendale, pp. 57-65 , PA.
14.
Sharpe, W.N. Jr., Coles, G., Jackson, K. and Edwards, R. (2001). Tensile Tests of Various Thin Films, In: Muhlstein, C. and Brown, S.B. (eds), Mechanical Properties of Structural Films, ASTM STP 1413, American Society for Testing and Materials, West Conshohocken, PA .
15.
Sharpe, W.N. Jr., Yuan, B. and Edwards, R.L. (1998). Fracture Tests of Polysilicon Film, Thin-Films - Stresses and Mechanical Properties VII., MRS Proceeding, pp. 51-56 , Warrendale, PA.
16.
Sniegowski, J.J. and de Boer, M.P. (2000). IC-Compatible Polysilicon Surface Micromachining , Annual Review Materials Science, 30: 299-333 .
17.
Tsuchiya, T. and Sakata, J. (2001). Tensile Testing of Thin Films Using Electrostatic Force Grip, In: Muhlstein, C. and Brown, S.B. (eds), Mechanical Properties of Structural Films, ASTM STP 1413, American Society for Testing and Materials, West Conshohocken, PA .
18.
Tsuchiya, T., Tabata, O., Sakata, J. and Taga, Y. (Dec. 1996). Tensile Testing of Polycrystalline Silicon Thin Films using Electrostatic Force Grip , Transactions of the Institute of Electrical Engineers of Japan, Part A, 116-E(10): 441-446 .
