In this paper, an in-depth analysis of IPMC (ionic polymer metal composite) as sensors is performed, motivated by application to flapping wing micro air vehicles. The effect of water uptake for different IPMC samples reveals a correlation between IPMC metal content and water uptake. The effect of introducing a mass to the end of High-frequency IPMC (HFI ∼ 20.9 Hz) sensor shows an improvement in the IPMC sensing behavior, whereas, for the Low-frequency IPMC (LFI ∼ 8.9 Hz) sensor, there is a reverse trend. Gold (Au) coating on an HFI sensor results in a decrease in resonant frequency. Different mass loaded on the Au coated HFI beams reveals that the pre-bending by adding end mass to HFI sensor is beneficial up to a specific mass level, after which the sensing voltage decreases. The optimized mass loading for the Au coated HFI is determined.
AureliMPrinceCPorfiriM, et al. (2009) Energy harvesting from base excitation of ionic polymer metal composites in fluid environments. Smart Materials and Structures19(1): 015003.
BattenBASinglerJRDickinsonBT (2006) Modeling of bioinspired sensors for flow separation detection for micro air vehicles. In: 3rd AIAA flow control conference, 5–8 June, San Francisco, CA. American Institute of Aeronautics and Astronautics (AIAA).
4.
BiswalDKBandopadhyaDDwivedySK (2014) Dynamic modeling and effect of dehydration on segmented IPMC actuators following variable parameter pseudo-rigid body modeling technique. Mechanics of Advanced Materials and Structures21(2): 129–138.
5.
BonomoCBrunettoPFortunaL, et al. (2008) A tactile sensor for biomedical applications based on IPMCs. IEEE Sensors Journal8(8): 1486–1493.
6.
BonomoCFortunaLGiannoneP, et al. (2006) Motion sensors and actuators based on ionic polymer-metal composites. In: BaglioSBulsaraA (eds) Device Applications of Nonlinear Dynamics. Berlin Heidelberg: Springer, pp. 83–99.
7.
BonomoCNegroCDFortunaL, et al. (2003) Characterization of IPMC strip sensorial properties: preliminary results. In: Circuits and Systems, ISCAS'03. Proceedings of the 2003 International Symposium, IEEE, 4, pp. 816. New York: IEEE.
8.
BrunettoPFortunaLGiannoneP, et al. (2010) A resonant vibrating tactile probe for biomedical applications based on IPMC. IEEE Transactions on Instrumentation and Measurement59(5): 1453–1462.
9.
ChaYVerottiMWalcottH, et al. (2013) Energy harvesting from the tail beating of a carangiform swimmer using ionic polymer–metal composites. Bioinspiration & Biomimetics8(3): 036003.
10.
ChenHFangSAwK (2010) Ionic polymer metallic composite as wearable impact sensor for sport science. International Journal of Biomechatronics and Biomedical Robotics1(2): 88.
11.
ChoS-MLeeD-W (2009) A biomimetic micro-collector based on an ionic polymer metal composite. Microelectronic Engineering86(4–6): 916–919.
12.
CohenYBBaoXSherritS, et al. (2002) Characterization of the electromechanical properties of Ionomeric Polymer-Metal Composite (IPMC). In: SPIE’s 9th annual international symposium on smart structures and materials, San Diego, CA, 11 July, pp. 286–293. International Society for Optics and Photonics.
13.
FengLS (2011) Effect of thickness and length of ion polymer metal composites (IPMC) on its actuation properties. Advanced Materials Research197–198: 401–404.
14.
GanleyTHungDLSZhuG, et al. (2011) Modeling and inverse compensation of temperature-dependent ionic polymer–metal composite sensor dynamics. IEEE/ASME Transactions on Mechatronics16(1): 80–89.
15.
GerdesJWGuptaSKWilkersonSA (2012) A review of bird-inspired flapping wing miniature air vehicle designs. Journal of Mechanisms and Robotics4(2): 021003.
16.
GhommemMCaloVMClaudelCG (2015) Micro-cantilever flow sensor for small aircraft. Journal of Vibration and Control21(10): 2043–2058.
17.
GrazianiSPaganoFPitroneN, et al. (2010) A software tool to estimate the dynamic behaviour of the IP2C samples as sensors for didactic purposes. Journal of Physics: Conference Series238(1).
18.
HsuWYGierkeTD (1983) Ion transport and clustering in nafion perfluorinated membranes. Journal of Membrane Science13(3): 307–326.
19.
KimKJShahinpoorM (2003) Ionic polymer metal composites: II. Manufacturing techniques. Smart Materials and Structures12(1): 65–79.
20.
KwasniewskiJDominikIKaszubaF (2014) Energy harvesting system based on Ionic polymer-metal composites–identification of electrical parameters. Polish Journal of Environmental Studies23(6).
21.
LeiHLiWTanX (2014) Encapsulation of ionic polymer-metal composite (IPMC) sensors with thick parylene: fabrication process and characterization results. Sensors and Actuators A: Physical217: 1–12.
22.
LeiHLimCTanX (2013) Modeling and inverse compensation of dynamics of base-excited ionic polymer–metal composite sensors. Journal of Intelligent Material Systems and Structures24(13): 1557–1571.
23.
LeiHLimCTanX (2015) Humidity-dependence of IPMC sensing dynamics: characterization and modeling from a physical perspective. Meccanica50(11): 2663–2673.
24.
MajsztrikPBocarslyABenzigerJ (2008a) Water permeation through Nafion membranes: the role of water activity. The Journal of Physical Chemistry B112(51): 16280–16289.
25.
MajsztrikPWBocarslyABBenzigerJB (2008b) Viscoelastic response of Nafion. Effects of temperature and hydration on tensile creep. Macromolecules41(24): 9849–9862.
26.
MajsztrikPWSatterfieldMBBocarslyAB, et al. (2007) Water sorption, desorption and transport in Nafion membranes. Journal of Membrane Science301(1–2): 93–106.
27.
Nemat-NasserS (2002) Micromechanics of actuation of ionic polymer-metal composites. Journal of Applied Physics92(5): 2899–2915.
28.
Nemat-NasserSLiJY (2000) Electromechanical response of ionic polymer-metal composites. Journal of Applied Physics87(7): 3321–3331.
29.
Nemat-NasserSWuY (2003) Comparative experimental study of ionic polymer–metal composites with different backbone ionomers and in various cation forms. Journal of Applied Physics93(9): 5255–5267.
30.
Nemat-NasserSWuY (2006) Tailoring the actuation of ionic polymer–metal composites. Smart Materials and Structures15(4): 909–923.
31.
OnishiKSewaSAsakaK, et al. (2000) Bending response of polymer electrolyte actuator. In: Smart Structures and Materials 2000: Electroactive Polymer Actuators and Devices (EAPAD), Newport Beach, CA, USA. Washington, USA: SPIE.
32.
OnishiKSewaSAsakaK, et al. (2001) Morphology of electrodes and bending response of the polymer electrolyte actuator. Electrochimica Acta46(5): 737–743.
33.
ParkK (2011) Characterization of the solvent evaporation effect on ionic polymer-metal composite sensors. Journal of the Korean Physical Society59(6): 3401–3409.
34.
PengYCaoJLiuL, et al. (2016) A piezo-driven flapping wing mechanism for micro air vehicles. Microsystem Technologies23(4): 967–973.
35.
PunningAKruusmaaMAablooA (2007) Surface resistance experiments with IPMC sensors and actuators. Sensors and Actuators A: Physical133(1): 200–209.
36.
ShahinpoorMBar-CohenYSimpsonJO, et al. (1998). Ionic polymer-metal composites (IPMCs) as biomimetic sensors, actuators and artificial muscles-a review. Smart Materials and Structures7(6): R15.
37.
ShahinpoorMKimKJ (2000) The effect of surface-electrode resistance on the performance of ionic polymer-metal composite (IPMC) artificial muscles. Smart Materials and Structures9(4): 543–551.
38.
ShahinpoorMKimKJ (2001) Ionic polymer-metal composites: I. Fundamentals. Smart Materials and Structures10(4): 819.
39.
ShojiEHirayamaD (2007) Effects of humidity on the performance of ionic polymer−metal composite actuators: experimental study of the back-relaxation of actuators. The Journal of Physical Chemistry B111(41): 11915–11920.
40.
SwarrupSJGanguliR (2015) Effect of mass loading on ionic polymer metal composite actuators and sensors. Electroactive Polymer Actuators and Devices (EAPAD). Bellingham, WA: International Society for Optics and Photonics.
41.
TiwariR (2010) Modeling and Characterization of IPMC Energy Harvesters. Saarbrucken: Lambert Academic.
42.
TiwariR (2012) Ionic polymer–metal composite mechanoelectric transduction: effect of impedance. International Journal of Smart and Nano Materials3(4): 275–295.
43.
TsaiC-EHwangB-J (2007) Intermolecular interactions between methanol/water molecules and Nafion™ membrane: an infrared spectroscopy study. Fuel Cells7(5): 408–416.
44.
VirkGSHarveyDRChochlidakisI, et al. (2006) Integrated IPMC sensor-actuator devices for walking robots. In: 3rd International Conference on Autonomous Robots and Agents-ICARA, Palmerston North, Palmerston North New Zealand, 12–14 December 2006.
45.
WangLYuanFG (2008) Vibration energy harvesting by magnetostrictive material. Smart Materials and Structures17(4): 045009.
46.
YamakitaMSeraAKamamichiN, et al. (2006) Integrated design of IPMC actuator/sensor. In: Proceedings IEEE International Conference on Robotics and Automation (ICRA), Orlando, FL, 15–19 May, pp. 1834–1839. New York: IEEE.
