Assessment of human bones encompassing physiological decay and damage using piezo sensors in non-bonded configuration

Abstract

In the recent years, several biomedical applications of lead zirconate titanate piezo-electric ceramic patches based on the electro-mechanical impedance technique have been reported in the literature. However, practical application of the technique on live subjects is severely hampered due to the requirement of bonding the patch with bone or cartilage with an adhesive. In addition, live subjects have skin cover over the bone. This article proposes and evaluates the feasibility of employing lead zirconate titanate patches as biomedical sensors in non-bonded configuration for assessing the physiological conditions of bones. For this purpose, a special design is proposed where the lead zirconate titanate patch is first bonded on a thin aluminum strip, which is in turn clamped securely on the biomedical subject. The proposed configuration is investigated both in vitro and in vivo. The non-bonded piezo sensors are first investigated to identify dynamic parameters of the bone through lab-based experimental study involving artificial bones. Thereafter, physiological damage and decay conditions are artificially simulated in the experimental bones and the same are correlated with changes in conductance signatures from the non-bonded piezo sensor as well as the lead zirconate titanate patch in the conventional adhesively bonded (direct bonding to the subject) configuration. The trend of the conductance signatures in the healthy and the damaged conditions from the non-bonded piezo sensor is found to correlate well with the corresponding signatures from the directly bonded piezo sensor. At the same time, the repeatability of the signatures is also found to be satisfactory. After success in bare bones, the non-bonded piezo sensor configuration is extended to monitor the condition of bones covered with skin and tissue, simulated in the lab with the aid of silicone-based coating. Finally, a proof-of-concept experiment on a live human subject is successfully demonstrated. The overall results of the study demonstrate very good prospects of employing lead zirconate titanate patches in non-bonded piezo sensor mode for monitoring the condition of human bones and other related biomedical subjects.

Keywords

Lead zirconate titanate electro-mechanical impedance technique bone non-bonded piezo sensor biomedical engineering

Get full access to this article

View all access options for this article.

References

Agilent Technologies (2014) Test and Measurement Catalogue. Santa Clara, CA: Agilent Technologies.

Bender

Friedman

Giurgiutiu

Watson

Fitzmaurice

Yost

(2006) The use of biomedical sensors to monitor capsule formation around soft tissue implants. Annals of Plastic Surgery56(1): 72–77.

Bhalla

Bajaj

(2008) Bone characterization using piezo-transducers as bio-medical sensors. Strain44(6): 475–478.

Bhalla

Soh

(2003) Structural impedance based damage diagnosis by piezo-transducer. Earthquake Engineering & Structural Dynamics32(12): 23–33.

Bhalla

Suresh

(2013) Condition monitoring of bones using piezo-transducers. Meccanica48(9): 2233–2244.

Bhalla

Gupta

Bansal

Garg

(2009) Ultra low cost adaptations of electro-mechanical impedance technique for structural health monitoring. Journal of Intelligent Material Systems and Structures20(8): 991–999.

Boemio

Rizzo

Nardo

(2011) Assessment of dental implant stability by means of the electromechanical impedance method. Smart Materials and Structures20(4): 11.

Chopra

(1995) Dynamics of Structures: Theory and Applications to Earthquake Engineering. Englewood Cliffs, NJ: Prentice Hall.

Christopoulou

Stavropoulou

Anastassopoulos

Panteliou

Papadaki

Karamanos

Panagiotopoulos

(2006) Evaluation of modal damping factor as a diagnostic tool for osteoporosis and its relation with serum osteocalcin and collagen I N-telopeptide for monitoring the efficacy of alendronate in ovariectomized rats. Journal of Pharmaceutical and Biomedical Analysis41(3): 891–897.

10.

Engineering Toolbox (2015), http://www.engineeringtoolbox.com

11.

Erickson

Catanese

III Keaveny

(2002) Evolution of the biomechanical material properties of the femur. Anatomical Record268: 115–124.

12.

Giurgiutiu

Rogers

(1998) Recent advancement in the electromechanical impedance method for structural health monitoring and NDE. Proceedings of SPIE3329: 536–547.

13.

Giurgiutiu

Zagrai

(2002) Embedded self-sensing piezoelectric active sensors for on-line structural identification. Journal of Vibration and Acoustics124(1): 116–125.

14.

Lim

Soh

(2012) Effect of varying axial load under fixed boundary condition on admittance signatures of electromechanical impedance technique. Journal of Intelligent Material Systems and Structures23(7): 815–826.

15.

Lim

Soh

(2013) Damage detection and characterization of EMI technique under varying axial load. Smart Structures and Systems11(4): 349–364.

16.

Park

Yun

Roh

Lee

(2006) PZT-based active damage detection techniques for steel bridge components. Smart Materials and Structures15: 1734–1746.

17.

PI Ceramic (2015), http://www.piceramic.com

18.

Ribolla

ELM

Rizzo

Gulizzi

(2014) On the use of the electromechanical impedance technique for the assessment of dental implant stability: modeling and experimentation. Journal of Intelligent Material Systems and Structures10: 1–15.

19.

Ritchie

Nalla

Kruzie

(2006) Fracture and ageing in bone: toughness and structural characterization. Strain42: 225–232.

20.

Soh

Bhalla

(2005) Calibration of piezo-impedance transducers for strength prediction and damage assessment of concrete. Smart Materials and Structures14(4): 671–684.

21.

Soh

Tseng

Bhalla

Gupta

(2000) Performance of smart piezoceramic patches in health monitoring of a RC bridge. Smart Materials and Structures9(4): 533–542.

22.

Yang

Lim

Soh

(2008) Practical issues related to the application of electro mechanical impedance technique in the structural health monitoring of civil structures: I. experiment. Smart Materials and Structures17(3): 14.