Design studies on cellular structures with pneumatic artificial muscle inclusions for modulus variation

Abstract

This article presents a variable modulus cellular structure based on a hexagonal unit cell with pneumatic artificial muscle inclusions. The cell is pin-jointed, loaded in the horizontal direction, with three pneumatic artificial muscles (one vertical pneumatic artificial muscle and two horizontal pneumatic artificial muscles) oriented in an “H” configuration between the vertices of the cell. A method for calculation of the hexagonal cell modulus is introduced, as is an expression for the balance of tensile forces between the horizontal and vertical pneumatic artificial muscles. Simulation is then compared to experimental measurement of the unit cell modulus in the horizontal direction over a pressure range of 682 kPa, and an increase in cell modulus of 200% is demonstrated experimentally. A design study considering parametric variation in cell angle, vertical to inclined wall length ratio, and pneumatic artificial muscle contraction ratios shows that changes in modulus of over 1000% are possible when the pneumatic artificial muscles are pressurized to 1992 kPa. This concept provides a way to create a structural unit cell whose in-plane modulus can be tuned based on the orientation of pneumatic artificial muscles within the cell and the pressure supplied to the individual muscles.

Keywords

pneumatic artificial muscle variable modulus hexagonal cell

Get full access to this article

View all access options for this article.

References

Barbarino

Pontecorvo

Gandhi

(2012) Cellular honeycomb-like structures with internal buckling and viscous elements for simultaneous load-bearing and dissipative capability. In: Proceedings of the ASME 2012 conference on smart materials adaptive structures and intelligent systems, Stone Mountain, GA, 19–21 September.

Bland

Snyder

Kudva

. (2014) A novel structural element combining load carrying and energy dissipation capability. In: Proceedings of the AIAA SciTech 2014 conference, National Harbor, MD, 13–17 January.

Chen

Yin

Liu

. (2011) Structural design and analysis of morphing skin embedded with pneumatic muscle fibers. Smart Materials and Structures 20(8): 085033.

Gaylord

(1958) Fluid actuated motor system and stroking device. US Patent No. 2,844,126.

Kim

G-W

Wang

(2010) Variable stiffness actuator based on fluidic flexible matrix composites and piezoelectric-hydraulic pump. In: Proceedings of the SPIE active and passive smart structures and integrated systems conference (ed Ghasemi-Nejhad

), San Diego, CA, 7 March.

Kothera

Jangid

Sirohi

. (2009) Experimental characterization and static modeling of McKibben actuators. Journal of Mechanical Design 131(9). DOI: 10.1115/1.3158982

Philen

(2008) Sliding mode control of variable modulus structures based upon fluidic flexible matrix composites. In: Proceedings of the 49th AIAA/ASME/ASCE/AHS/ASC structures structural dynamics and materials conference, Schaumburg, IL, 7–10 April.

Philen

(2009) On the applicability of fluidic flexible matrix composite variable impedance materials for prosthetic and orthotic devices. Smart Materials and Structures 18(10): 104023.

Philen

(2010) Tunable modulus structures utilizing fluidic flexible matrix composites: analytical and experimental investigations. In: Proceedings of the 51st AIAA/ASME/ASCE/AHS/ASC structures, structural dynamics, and materials conference, Orlando, FL, 12–15 April.

10.

Philen

(2011) Force tracking control of fluidic flexible matrix composite variable stiffness structures. Journal of Intelligent Material Systems and Structures 22(1): 31–43.

11.

Philen

(2012) Fluidic flexible matrix composite semi-active vibration isolation mounts. Journal of Intelligent Material Systems and Structures 23(3): 353–363.

12.

Pontecorvo

Barbarino

Gandhi

(2012) Cellular honeycomb-like structures with internal inclusions in the unit-cell. In: Proceedings of the ASME 2012 conference on smart materials adaptive structures and intelligent systems, Stone Mountain, GA, 19–21 September.

13.

Schulte

(1961) The Characteristics of the McKibben Artificial Muscle: The Application of External Power in Prosthetics and Orthotics. Washington, DC: National Academy of Sciences—National Research Council (Appendix H, Publication 874), pp. 94–115.