Sage Journals: Discover world-class research

Abstract

We investigate the effects of shape variations of a cantilever beam on its performance as an energy harvester. The beam is composed of piezoelectric and metallic layers (unimorph design) with a rigid mass attached to its free end. A reduced-order model based on a one-mode Galerkin approach is derived. Solutions for the tip displacement, generated voltage, and harvested power are then obtained. Linear and quadratic shape variations are considered in order to design piezoelectric energy harvesters that can generate energy at low frequencies and maximize the harvested energy. The results show that the fundamental natural frequency and mode shape are strongly affected when the shape of the beam is varied. The influence of the electrical load resistance and the shape parameters at resonance on the system’s performance is discussed. It is determined that for specific resistance values, the quadratic shape can yield up to two times the energy harvested by a rectangular shape.

Keywords

Energy harvesting piezoelectric material variable-shaped beams differential quadrature method distributed model

Get full access to this article

View all access options for this article.

References

Abdelkefi

(2012) Global nonlinear analysis of piezoelectric energy harvesting from ambient and aeroelastic vibrations. PhD Dissertation, Virginia Polytechnic Institute and State University, Blacksburg, VA.

Abdelkefi

Hajj

Nayfeh

(2013) Piezoelectric energy harvesting from transverse galloping of bluff bodies. Smart Materials and Structures 22: 015014.

Abdelkefi

Najar

Nayfeh

. (2011) An energy harvester using piezoelectric cantilever beams undergoing coupled bending-torsion vibrations. Smart Materials and Structures 20: 115007.

Abdelkefi

Nayfeh

Hajj

(2012) Effects of nonlinear piezoelectric coupling on energy harvesters under direct excitation. Nonlinear Dynamics 67: 1221–1232.

Anton

Sodano

(2007) A review of power harvesting using piezoelectric materials (2003–2006). Smart Materials and Structures 16: 1–21.

Benasciutti

Moro

Zelenika

. (2010) Vibration energy scavenging via piezoelectric bimorphs of optimized shapes. Microsystem Technologies 16: 657–668.

Ching

NNH

Wong

. (2002) A laser-micromachined multi-modal resonating power transducer for wireless sensing systems sensors and actuators. Sensors and Actuators A: Physical 97–98: 685–690.

Cook-Chennault

Thambi

Sastry

(2008) Powering MEMS portable devices—a review of non-regenerative and regenerative power supply systems with emphasis on piezoelectric energy harvesting systems. Smart Materials and Structures 17: 043001.

El-hami

Glynne-Jones

White

. (2001) Design and fabrication of a new vibration-based electromechanical power generator. Sensors and Actuators A: Physical 92: 335–342.

10.

Erturk

Inman

(2009) An experimentally validated bimorph cantilever model for piezoelectric energy harvesting from base excitations. Smart Materials and Structures 18: 025009.

11.

Goldschmidtboeing

Woias

(2008) Characterization of different beam shapes for piezoelectric energy harvesting. Journal of Micromechanics and Microengineering 18: 104013.

12.

Masana

Daqaq

(2011) Electromechanical modeling and nonlinear analysis of an axially-loaded energy harvesters. Journal of Vibration and Acoustics: Transactions of the ASME 330: 6036–6052.

13.

Mateu

Moll

(2005) Optimum piezoelectric bending beam structures for energy harvesting using shoe inserts. Journal of Intelligent Material Systems and Structures 16: 835–845.

14.

Meninger

Mur-Miranda

Amirtharajah

. (2001) Vibration-to-electric energy conversion. IEEE Transactions on Very Large Scale Integration VLSI Systems 9: 64–76.

15.

Mittal

Jiwari

(2011) Numerical study of two-dimensional reaction-diffusion brusselator system by differential quadrature method. International Journal for Computational Methods in Engineering Science and Mechanics 12: 14–25.

16.

Nayfeh

Pai

(2004) Linear and Nonlinear Structural Mechanics. New York: Wiley.

17.

Priya

(2007) Advances in energy harvesting using low profile piezoelectric transducers. Journal of Electroceramics 19: 165–182.

18.

Roundy

Leland

Baker

. (2005) Improving power output for vibration-based energy scavengers. IEEE Pervasive Computing 4: 28–36.

19.

Shahruz

(2006) Design of mechanical band-pass filters for energy scavenging. Journal of Sound and Vibration 292: 987–998.

20.

Sodano

Park

Inman

(2004) A review of power harvesting from vibration using piezoelectric materials. The Shock and Vibration Digest 36: 197–205.

21.

Sterken

Fiorini

Baert

. (2003) An electret-based electrostatic µ-generator. In: 12th international conference on TRANSDUCERS, solid-state sensors, actuators and microsystems, Boston, MA, 8–12 June 2003, vol. 2, pp. 1291–1294. IEEE

22.

Tomasiello

(1998) Differential quadrature method: application to initial-boundary-value problems. Journal of Sound and Vibration 218: 573–585.

Design and performance of variable-shaped piezoelectric energy harvesters

Abstract

Keywords

Get full access to this article

References