Modeling and Comparison of Bimorph Power Harvesters with Piezoelectric Elements Connected in Parallel and Series

Abstract

Power harvesting devices are designed to convert the ambient energy surrounding a system to usable electric energy. The strong desire to create self-powered systems, which do not rely on traditional energy sources such as electrochemical batteries has led to the rapid growth of this field. One type of energy harvesting is the use of piezoelectric materials to directly transform ambient vibration to electrical energy. In the majority of applications the piezoelectric is configured as a bimorph bender, where the two patches of piezoceramic material can be electrically connected in either series or parallel. A reduced model will be used here to develop a set of closed form solutions to the power harvesting performance of the system based on the electrical connection of the piezoelectrics. It will be theoretically and experimentally shown that the maximum power output and efficiency is independent of the electrical connection. However, the voltage (and current) outputs between a series and parallel conditions are related by a factor of two with a symmetric system. Additionally, a critical impedance will be derived to serve as a criterion on selecting the appropriate electrical connection between the piezoelectrics to tune the systems performance based on the impedance of external circuitry. Key

Keywords

Words: energy harvesting piezoelectric vibration.

Get full access to this article

View all access options for this article.

References

Anton, S.R. and Sodano, H.A. 2007. ‘‘A Review of Power Harvesting Using Piezoelectric Materials (2003-2006),’’ Smart Materials and Structures , 16:R1-R21.

Erturk, A. and Inman, D.J. 2008. ‘‘Analytical Modeling of Cantilevered Piezoelectric Energy Harvesters for Transverse and Longitudinal Base Motions,’’ In: Proceeding of the 49th AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference, April 7-10, Schaumburg, IL.

Feenstra, J. , Granstrom, J. and Sodano, H.A. 2008. ‘‘Mechanically Amplified Piezoelectric Stack Actuators for Harvesting Electrical Energy from a Backpack, ’’ Mechanical Systems and Signal Processing, 22:721-734.

Granstrom, J. , Feenstra, J. and Sodano, H.A. 2007. ‘‘Energy Harvesting from a Backpack Instrumented with Piezoelectric Shoulder Straps,’’ Smart Materials and Structures, 16:1810-1820.

Hagood, N.W. , Chuang, W.H. and von Flotow, A. 1990. ‘‘Modeling of Piezoelectric Actuator Dynamics for Active Structural Control,’’ Journal of Intelligent Material Systems and Structures, 1:327-354.

Jeon, Y.B. , Sood, R. , Jeong, J.H. and Kim, S.G. 2005. ‘‘MEMS Power Generator with Transverse Mode Thin Film PZT,’’ Sensors and Actuators A , 122:16-22.

Lesieutre, G.A. 1998. ‘‘Vibration Damping and Control Using Shunted Piezoelectric Materials,’’ The Shock and Vibration Digest, 30:187-195.

Lesieutre, G.A. , Ottman, G.K. and Hofmann, H.F. 2004. ‘‘Damping as a Result of Piezoelectric Energy Harvesting,’’ Journal of Sound and Vibration , 269:991-1001.

Liao, Y. and Sodano, A.H. 2008. ‘‘Model of a Single Mode Energy Harvester and Properties for Optimal Power Generation,’’ Smart Materials and Structures, 17:065026.

10.

Liao, Y. and Sodano, A.H. 2009a. ‘‘Optimal Parameters and Power Characteristics of Piezoelectric Energy Harvesters with an RC Circuit,’’ Smart Materials and Structures, 18:045011.

11.

Liao, Y. and Sodano, A.H. 2009b. ‘‘Structural Effects and Energy Conversion Efficiency of Power Harvesting,’’ Journal of Intelligent Material Systems and Structures, 20:505-514.

12.

Platt, S.R. , Farritor, S. and Haider, H. 2005. ‘‘The Use of Piezoelectric Ceramics for Electric Power Generation within Orthopedic Implants’’ ,IEEE/ASME Transactions on Mechatronics, 10:455-461.

13.

Priya, S. 2005. ‘‘Modeling of Electric Energy Harvesting Using Piezoelectric Windmill,’’ Applied Physics Letters , 87:184101.

14.

Renno, J.M. , Daqaq, M.F. and Inman, D.J. 2009. ‘‘On the Optimal Energy Harvesting from a Vibration Source,’’ Journal of Sound and Vibration , 320:386-405.

15.

Roundy, S. , Wright, P.K. and Rabaey, J. 2003. ‘‘A Study of Low Level Vibrations as a Power Source for Wireless Sensor Nodes,’’ Computational Communications, 26:1131-44.

16.

Roundy, S. , Leland, E.S. , Baker, J. , Carleton, E. , Reilly, E. , Lai, E. , Otis, B. , Rabaey, J.M. , Wright, P.K. and Sundararajan, V. 2005. ‘‘Improving Power Output for Vibration-based Energy Scavengers,’’ IEEE Pervasive Computing , 4:28-36.

17.

Sodano, H.A. , Park, G. and Inman, D.J. 2004. ‘‘Estimation of Electric Charge Output for Piezoelectric Energy Harvesting,’’ Journal of Strain, 40:49-58.

18.

Taylor, G.W. , Burns, J.R. , Kammann, S.M. , Powers, W.B. and Welsh, T.R. 2001. ‘‘The Energy Harvesting Eel: A Small Subsurface Ocean/River Power Generator,’’ IEEE Journal of Oceanic Engineering, 26:539-547.

19.

Twiefel, J. , Richter, B. , Sattel, T. and Wallaschek, J. 2008. ‘‘Power Output Estimation and Experimental Validation for Piezoelectric Energy Harvesting Systems,’’ Journal of Electroceramics, 20:203-208.

20.

Williams, C.B. and Yates, R.B. 1996. ‘‘Analysis of a Micro-electric Generator for Microsystems,’’ Sensors and Actuators A, 52:8-11.