Sage Journals: Discover world-class research

Abstract

Ionic polymers are electromechanically coupled smart materials that can be used as both actuators and sensors. As flexible actuators, these materials have been known to exhibit nonlinear behavior, but the present work shows that linear control techniques can greatly improve the open-loop response. However, because material dehydration results in changing system parameters, the linear control designs only offer a stable system for a limited amount of time (approximately 30 s). This study shows that the application of integral control to ionic polymer actuators can provide precise tracking performance to a reference step input. The actuator’s response to frequencies is also studied, in both the time and frequency domain. The frequency response analysis offers insight into the bandwidth of the actuators, where it was shown that the closed-loop bandwidth of the cantilever actuator is approximately 10% of its first resonance frequency. Simulations are performed with a linear empirical model of a cantilevered actuator, while both clamped-free and clamped-clamped configurations are tested in control experiments.

Keywords

ionic polymer electroactive polymer micromanipulation bandwidth flexible actuator

Get full access to this article

View all access options for this article.

References

Akle, B. , Hickner, M. , Leo, D. and McGrath, J. 2003. “Electroactive Polymers Based on Novel Ionomers,” In: ASME International Mechanical Engineering Congress, Washington, D.C., Paper No. IMECE2003-43561.

Arena, P. , Bonomo, C. , Fortuna, L. and Frasca, M. , 2002. “Electro-Active Polymers as CNN Actuators for Locomotion Control,” In: IEEE International Symposium on Circuits and Systems, Vol. 4, pp. 281-284 .

Asaka, K. and Oguro, K. 2000. “Bending of Polyelectrolyte Membrane Platinum Composites by Electric Stimuli, Part II. Response Kinetics,” Journal of Electroanalytical Chemistry, 480: 186-198 .

Bar-Cohen, Y. , Bao, X. , Sherrit, S. and Lih, S.-S. 2002. “Characterization of the Electromechanical Properties of Ionomeric Polymer-Metal Composite (IPMC),” In: SPIE Smart Materials Conference, Vol. 4695, pp. 286-293 .

Bennett, M. and Leo, D. 2003. “Manufacture and Characterization of Ionic Polymer Transducers Employing Non-precious Metal Electrodes,” Smart Materials and Structures, 12(3): 424-436 .

Bennett, M. and Leo, D. 2004. “Ionic Liquids as Novel Solvents for Ionic Polymer Transducers,” In: SPIE Smart Materials Conference, Vol. 5383.

Bhat, N. and Kim, W.-J. 2003. “Precision Control of Force Produced by Ionic Polymer Metal Composite,” In: ASME/IMECE International Mechanical Engineering Congress, Washington D.C., Paper No. IMECE2003-42709.

de Gennes, P. , Okumura, K. , Shahinpoor, M. and Kim, K. (2000). “Mechanoelectric Effects in Ionic Gels,” Europhysics Letters, 50(4): 513-518 .

Farinholt, K. and Leo, D. 2004. “Effects of Counter-ion, Solvent Type and Loading Condition on the Material Response of Ionic Polymer Transducers,” In: SPIE Smart Materials Conference, Vol. 5387.

10.

Kanno, R. , Kurata, A. , Hattori, M. , Tadokoro, S. and Takamori, T. (1994). “Characteristics and Modeling of ICPF Actuator,” In: Japan-USA Symposium on Flexible Automation, Vol. 2, pp. 691-698 .

11.

Kothera, C. , Leo, D. and Robertson, L. 2003. “Hydration and Control Assessment of Ionic Polymer Actuators,” In: AIAA Structures, Structural Dynamics, and Materials Conference, Norfolk, VA, Paper No. AIAA2003-1441.

12.

Leo, D. , Newbury, K. , Mallavarapu, K. , Griffn, S. and Shahinpoor, M. 2001. “Ionic Polymer Devices for Optical Positioning Systems,” In: AIAA Space Conference, Vol. 15, pp. 328-338 , Albuquerque, NM.

13.

Mallavarapu, K. and Leo, D. 2001. “Feedback Control of the Bending Response of Ionic Polymer Actuators,” Journal of Intelligent Material Systems and Structures, 12: 143-155 .

14.

Nemat-Nasser, S. 2002. “Micromechanics of Actuation of Ionic Polymer-metal Composites,” Journal of Applied Physics, 92(2): 2899-2915 .

15.

Newbury, K. 2002. Characterization, Modeling, and Control of Ionic Polymer Transducers, Ph.D. Thesis, Virginia Polytechnic Institute and State University.

16.

Newbury, K. and Leo, D. 2002. “Electromechanical Modeling and Characterization of Ionic Polymer Benders,” Journal of Intelligent Material Systems and Structures, 13: 51-60 .

17.

Oguro, K. , Kawami, Y. and Takenaka, H. 1992. “Bending of an Ion-Conducting Polymer Film-Electrode Composite by an Electric Stimulus at Low Voltage,” Trans. Journal of Micromachine Society, 5: 27-30 .

18.

Richardson, R. , Levesley, M. , Brown, M. , Hawkes, J. , Watterson, K. and Walker, P. 2003. “Control of Ionic Polymer Metal Composites,” IEEE/ASME Transactions on Mechatronics, 8(2): 245-253 .

19.

Sadeghipour, K. , Salomon, R. and Neogi, S. 1992. “Development of a Novel Electrochemically Active Membrane and ’Smart’ Material Based Vibration Sensor/Damper,” Smart Materials and Structures, 1: 172-179 .

20.

Shahinpoor, M. 1992. “Conceptual Design, Kinematics and Dynamics of Swimming Robotics Structures using Ionic Polymeric Gel Muscles,” Smart Materials and Structures, 1(1): 91-94 .

21.

Tadokoro, S. , Yamagami, S. , Takamori, T. and Oguro, K. 2000. “Modeling of Nafion-Pt Composite Actuators (ICPF) by Ionic Motion,” In SPIE Smart Materials and Structures, Vol. 3987, pp. 92-102 .

22.

Witherspoon, S. and Tung, S. 2002. “Design and Fabrication of an EAP Actuator System for Space Inflatable Structures,” In: AIAA Structures, Structural Dynamics, and Materials Conference, Denver, CO, Paper No. AIAA2002-1449.

23.

Xiao, Y. and Bhattacharya, K. 2001. “Modeling Electromechanical Properties of Ionic Polymers,” In SPIE Smart Materials Conference, Vol. 4329, pp. 292-300 .

Bandwidth Characterization in the Micropositioning of Ionic Polymer Actuators

Abstract

Keywords

Get full access to this article

References