The aim of this study is to investigate the optimum technique to disperse vapour grown carbon nanofibres (VGCNFs) in SC-1 epoxy uniformly and to evaluate their effect on the performance of SC-1 epoxy. In this study, ultrasonication and Thinky mixing methods were used either in isolation or in combination with 3-roll shear mixing. To achieve better dispersion, VGCNF was tested either by mixing with SC-1 resin directly or premixed with a solvent and then mixed with SC-1 resin after evaporating the solvent. Flexural tests were performed to evaluate mechanical performances, and the results exhibited 25.60% and 8.88% improvement of flexural strength and modulus, respectively over neat epoxy with only 0.2 wt.% loading. Dynamic Mechanical Analysis (DMA), Differential Scanning Calorimetry (DSC), Thermogravimetric Analysis (TGA) indicated improvement in storage modulus, Tg, inflection temperature and residue content respectively over neat SC-1 epoxy. The high viscosity found by rheological analysis prevents their ubiquitous use in fibre reinforced composites. Thermal and mechanical properties at higher loading conditions were seen either to reduce or not significantly improve. These results indicate that the methods used for dispersion are suitable for low weight percent loading only.
ZhengY., and NingR., “Effect of Nanoparticles SiO2 on the Performance of Nanocomposites,”Mater. Lett., 57 (2003), 2940–2944.
2.
ZhouY., PervinF., JeelaniS., and MallickP.K., “Improvement in Mechanical Properties of carbon Fabric-Epoxy Composite Using Carbon Nanofibres,”J. Mater. Process. Technol., 198 (2008), 445–53.
3.
SandlerJ., ShafferM.S.P., PrasseT., BauhoferW., SchulteK., and WindleA.H., “Development of a Dispersion Process for Carbon nanotubes in an Epoxy Matrix and the Resulting Electrical properties,”Polymer, 40 (1999), 5967–5971.
4.
BryningM.B., IslamM.F., KikkawaJ.M., and YodhA.G., “Very Low Conductivity Threshold in Bulk Isotropic Single-Walled Carbon Nanotube-Epoxy Composites,”Adv. Mater.17 (2005), 1186–1191.
5.
MiyagawaH., and DrzalL.T., “Thermo-Physical and Impact Properties of Epoxy Nanocomposites Reinforced by Single-Wall Carbon Nanotubes,”Polymer, 45 (2004), 5163–5170.
6.
LauK.T., LuM., LamC.K., CheungH.Y., ShengF.L., and LiH.L., “Thermal and Mechanical Properties of Single-Walled Carbon Nanotube Bundle-Reinforced Epoxy nanocomposites: The ole of Solvent for nanotube Dispersion,”Compos. Sci. Technol., 65 (2005), 719–725.
7.
MoniruzzamanM., DuF.M., and RomeroN., “Increased Flexural Modulus and Strength in SWNT/Epoxy Composites by a New Fabrication Method,”Polymer, 47 (2006), 293–298.
8.
GojnyF.H., WichmannM.H.G., FiedlerB., and SchulteK., “Influence of Different Carbon Nanotubes on the Mechanical Properties of Epoxy Matrix Composites – A Comparative Study,”Compos. Sci. Technol., 65 (2005), 2300–2313.
9.
SchulteK., GojnyF.H., FeddlerB., BrozaG., and SandlerJ., Carbon nano tube reinforced polymers- A state of the art review in Polymer composites-from nano to micro scale.FrederichK, FakirovS., ZhangZ., eds. Dordrecht Kluwer Publisher, (2005), pp 3–23.
10.
ThostensonE.T., and ChouT., “Processing-Structure-Multi-Functionality Property Relationship in Carbon Nanotube/Epoxy Composites,”Carbon, 44 (2006), 3022–3029.
11.
GojnyF.H., and SchulteK., “Functionalization effect on the thermo-mechanical behaviour of multi-wall carbon nanotube/epoxy-composites,”Compos. Sci. Tech., 64 (2004), 2303–2308.
12.
JunXu, DonoheeJohn P, and CharlesU. PittmanJr., Preparation, electrical and mechanical properties of vapour grown carbon fibre/vinyl ester composites. Composites: Part A, 35 (2004), 693–701.
13.
BalS., “Experimental study of mechanical and electrical properties of carbon nanofibre/epoxy composites,”Materials and Design, 31 (2010), 2406–2413.
14.
TibbettsG.G., LakeM.L., StrongK.L., and PriceB.P., “A review of the fabrication and properties of vapour-grown carbon nano fibre/polymer composite,”Composites Science and Technology, 67 (2007), 1709–1718.
15.
PattonR.D., PittmanC.U.Jr., WangL., and HillJ.R., “Vapor grown carbon fibre composites with epoxy and poly (phenylene sulphide) matrices,”Composites Part A: Appl Sci Mfg., 30 (1999), 1081–1091.
16.
RiceB.P., GibsonT., and LafadiK., “Development of multifunctional advanced composites using a VGNF enhanced matrix,” In: 49th International SAMPE symposium proceedings, Long Beach, USA, May; 2005.
17.
WangC.-S., and AlexanderM.D., US 6,680,016, January 29, 2004.
18.
GojnyF.H., WichmannM.H.G., KöpkeU., FiedlerB., and SchulteK., “Carbon nanotube-reinforced epoxy-composites: enhanced stiffness and fracture toughness at low nanotube content,”. Compos. Sci. Technol., 64 (2004), 2363–2371.
19.
WeiC.L., ZhangM.Q., RongM.Z., and FriedrichK., “Tensile performance improvement of low nanoparticles filled-polypropylene composites,”Comp Sci Tech., 62 (2002), 1327–1340.
20.
YasminA., AbotJ.L., and DanielI.M.“Processing of clay/epoxy nanocomposites by shear mixing,”Scripta Materialia, 49 (2003), 81–86.
21.
LiuX., and WuQ., “PP/clay nanocomposites prepared by grafting-melt intercalation,”Polymer, 42 (2001), 10013–10019.
22.
SeyhanA.T., GojnyF.H., TanogluM., and SchulteK., “Rheological and dynamic-mechanical behaviour of carbon nanotube/vinyl ester-polyester suspensions and their nanocomposites,”European Polymer Journal, 43 (2007), 2836–47.
23.
ZhouY., PervinF., RangariV.K., and JeelaniS., “Fabrication and evaluation of carbon nano fibre filled carbon/epoxy composite,”Materials Science and Engineering A, 426 (2006), 221–228.
24.
ChoiY.-K., SugimotoK., SongS.-M., GotohY., OhkpshiY., and EndoM., “Mechanical and physical properties of epoxy composites reinforced by vapour grown carbon nanofibres,”Carbon, 43 (2005), 2199–2208.
25.
LeeJ., AshokkumarM., KentishS., and GrieserF., “Effect of alcohols on the initial growth of multibubble sonoluminescence,”J. Phys. Chem. B, 110 (2006), 17282–17285.
26.
IsobeT., KameshimaY., NakajimaA., and OkadaK., Preparation and properties of porous alumina ceramics with uni-directionally oriented pores by extrusion method using a plastic substance as a pore former. J. Eur. Ceram. Soc., 27 (2007), 61–66.
27.
AllaouiA., HoaS.V., and PughM.D., “The electronic transport properties and microstructure of carbon nanofibre/epoxy composites,”Compos. Sci. Technol., 68 (2008), 410–416.
28.
RaoP., IwasaM., TanakaT., and KondohI., “Centrifugal casting of Al2O3-15 wt.% ZrO2 ceramic composites,”Ceramics International, 29 (2003), 209–212.
29.
ZhouY., PervinF., LewisL., and JeelaniS., “Experimental study on the thermal and mechanical properties of multi-walled carbon nanotube-reinforced epoxy,”Mater. Sci. Eng., A, 452 (2007), 657–664.
30.
LoeraA.G., CaraF., DumonM., and PascaultJ.P., “Porous epoxy thermosets obtained by a polymerization-induced phase separation process of a degradable thermoplastic polymer”, Macromolecules, 35 (2002), 6291–6297.
31.
RangariV.K., KoltypinY., CohenY.S., AurbachD., PalchikO., FelnerI., and GedankenA., “Preparation of amorphous magnetic nanoparticles embedded in polyvinyl alcohol using ultrasound radiation,”J. Mater. Chem., 10 (2000), 1125–1129.
32.
CookW.D., MehrabiM., and EdwardG.H., “Ageing and yielding in model epoxy thermosets,”Polymer, 40 (1999), 1209–1218.
33.
MerlinTheodore, “Studies on the kinetics and characterization of epoxy resin reinforced with a variety of functional multiwall carbon nanotubes,” PhD Thesis, Tuskegee University, 2008.
34.
WichmannM.H.G., SumflethJ., GojnyF.H., QuaresiminM., FiedlerB., and SchulteK.“Glass-fibre reinforced composites with enhanced mechanical and electrical properties-Benefits and limitations of a nanoparticle modified matrix,”Engineering Fracture Mechanics, 73 (2006), 2346–2359.
35.
ZhouY., PervinF., LewisL., and JeelaniS., “Fabrication and characterization of carbon/epoxy composites mixed with multi-walled carbon nanotubes,”Mater. Sci. Eng., A, 475 (2008), 157–165.
36.
LauK. T., LuM., and LiaoK., “Improved mechanical properties of coiled carbon nanotubes reinforced epoxy nanocomposites,”Composites Part A, 37 (2006), 1837–1840.
