Investigations on the coupling flow between full-scale last-stage steam turbine and low-pressure exhaust hood

Abstract

In a condensing steam turbine, the last-stage turbine and the condenser are connected by the low-pressure axial–radial exhaust hood. The exhaust hood has a complex geometry to make the flow change direction by 90°, while guiding the flow from the turbine to the condenser. During the operation, strong flow interactions between the turbine and the exhaust hood cause the flow pattern to become extremely complicated. The purpose of this paper is to investigate the coupling flow between the full-scale last-stage turbine and the low-pressure exhaust hood of a 600 MW steam turbine under actual operation conditions. The simulational calculations of the flow through the last stage turbine and the exhaust hood were realized by coupling calculations of turbine stage and exhaust hood in an external iterative manner. Equilibrium wet steam was selected as the flow medium. The coupling flow fields under different operation conditions were simulated and analyzed. It is found that the distributions of the turbine exit flow fields at different circumferential locations vary remarkably. The profiles of swirl angle and total pressure distributions at the turbine outlet change with the decrease of the mass flowrate, which further influence the flow behavior in the hood and lead to the reduction of the performance.

Keywords

Steam turbine exhaust hood full scale coupling flow

Get full access to this article

View all access options for this article.

References

Liu

Hynes

. The investigation of turbine and exhaust interactions in asymmetric flows—blade-row models applied. J Turbomach 2003; 125: 121–127.

Liu JJ and Hynes TP. The investigation of turbine and exhaust interactions in asymmetric flows part 2—turbine-diffuser-collector interaction. In: Proceeding of ASME Turbo Expo, Amsterdam, Netherlands, 3–6 June 2002, paper no. GT2002-30343, pp.1–10. New York: ASME.

Benim

Geiger

Doehler

. Modeling the flow in the exhaust hood of steam turbines under consideration of turbine-exhaust hood interaction. VDI Berichte NR 1995; 1185: 343–357.

Beevers A, Conju F, Pengue F, et al. An analysis of the merits of CFD for the performance prediction of a low pressure steam turbine radial diffuser. In: Proceeding of ASME Turbo Expo, Glasgow, Scotland UK, 14–18 June 2010, paper no. GT2010-22107, New York: ASME.

Yoon S, Stanislaus FJ, Mokulys T, et al. A three-dimensional diffuser design for the retrofit of a low pressure turbine using in-house exhaust design system. In: Proceeding of ASME Turbo Expo, Vancouver, British Columbia, Canada, 6–10 June 2011, paper no. GT2011-45466, pp.1–11. New York: ASME.

Gradzilewicz

Swirydczuk

Badur

. Methodology of CFD computations applied for analysis flow through steam turbine exhaust hood. Trans Inst Fluid-Flow Mach 2003; 113: 157–168.

Li ZG, Li J, Yan X, et al. Investigations on the flow pattern and aerodynamic performance of last stage and exhaust hood for large power steam turbines. In: Proceeding of ASME Turbo Expo, Copenhagen, Denmark, 11–15 June 2012, paper no. GT2012-69291, pp.1–9. New York: ASME.

Verstraete T, Prinsier J, Sante AD, et al. Design optimization of a low pressure steam turbine radial diffuser using an evolutionary algorithm and 3D CFD. In: Proceeding of ASME Turbo Expo, Copenhagen, Denmark, 11–15 June 2012, paper no. GT2012-69515, pp.1–9. New York: ASME.

Burton Z, Ingram G and Hogg S. A novel method of coupling the steam turbine exhaust hood and the last stage blades using the non-linear harmonic method. In: Proceeding of ASME Turbo Expo, San Antonio, Texas, USA, 3–7 June 2013, paper no. GT2013-94184, pp.1–10. New York: ASME.

10.

Štanstný

Škoda

Kolár

. 3D flow in the axial-radial exhaust hood of a steam turbine. J Therm Sci 1997; 6: 237–240.

11.

Štanstný

Tajc

Kolár

. Effects of inlet swirl on the flow in a steam turbine exhaust hood. J Therm Sci 2000; 9: 327–333. 326.

12.

Liu JJ, Cui YQ and Jiang HD. Investigation of flow in a steam turbin exhaust hood with/without turbine exit conditions simulated. In: Proceeding of ASME Turbo Expo, New Orleans, Louisiana, USA, 4–7 June 2001, paper no. GT2001-0488, pp.1–9. New York: ASME.

13.

Finzel C, Schatz M, Casey MV, et al. Experimental investigation of geometrical parameters on the pressure recovery of low pressure steam turbine exhaust hoods. In Proceeding of ASME Turbo Expo Vancouver, British Columbia, Canada, 6–10 June 2011, paper no. GT2011-45302, pp.1–9. New York: ASME.

14.

Tanuma T, Sasao Y, Yamamoto S, et al. Numerical investigation of three-dimensional wet steam flows in an exhaust diffuser with non-uniform inlet flows from the turbine stages in a steam Turbine. In: Proceeding of ASME Turbo Expo, Copenhagen, Denmark, 11–15 June 2012, paper no. GT2012-69496, pp.1–14. New York: ASME.

15.

Fu JL, Liu JJ and Zhou SJ. Experimental and numerical investigation of interactions between axial turbine and non-axisymmetric exhaust hood. In Proceeding of ASME Turbo Expo, Berlin, Germany, 9–13 June 2008, paper no. GT2008-69496, pp.1–15. New York: ASME.

16.

Liu

Zhou

. Unsteady interactions between axial turbine and nonaxisymmetric exhaust hood under different operational conditions. J Turbomach 2012; 134: 041002-1–041002-11.

17.

Liu

. Influences of inflow condition on non-axisymmetric flows in turbine exhaust hood. J Therm Sci 2008; 17: 289–382.