Effect of tip clearance on impeller discharge flow and vaneless diffuser performance of a centrifugal compressor

Abstract

To see the tip clearance effect on a centrifugal compressor, time-resolved flow measurements are carried out at the discharge of a centrifugal compressor impeller with a diameter of 280 mm. The impeller is 30° back swept and is operated at a blade tip speed of 260 m/s, which is a rather high speed for measuring time-resolved flow. Six levels of tip clearance ratio ranging from 0.06 to 0.21 were tested. A fast response aerodynamic probe equipped with a single pressure sensor is used for the flow measurements. The correlation between the impeller efficiency and the tip clearance is presented. The mean flow variation from hub to shroud is obtained and its dependence on the tip clearance is discussed. The measured time-resolved flow at impeller exit differs from the classical jet-wake flow model. Four kinds of flow patterns (blade wake, jet, channel wake, and tip clearance flow) are observed at the impeller discharge plane. By increasing the tip clearance, the total pressure loss in the vaneless diffuser decreases, while the impeller loss increases. One-dimensional flow calculations of the vaneless diffuser show that the matching constant of a skin friction coefficient is decreased by increasing the tip clearance.

Keywords

Tip clearance jet wake time-resolved flow vaneless diffuser centrifugal compressor

Get full access to this article

View all access options for this article.

References

Pampreen

. Small turbomachinery compressor and fan aerodynamics. ASME J Eng Power 1973; 95: 251–256.

Senoo

Ishida

. Deterioration of compressor performance due to tip clearance of centrifugal impellers. ASME J Turbomachinery 1987; 109(1): 55–61.

Chriss

Hathaway

Wood

. Experimental and computational results from the NASA Lewis low-speed centrifugal impeller at design and part-flow conditions. ASME J Turbomachinery 1996; 118(1): 55–65.

Hathaway

Wood

. Application of a multi-Block CFD code to investigate the impact of geometry modeling on centrifugal compressor flow field predictions. ASME J Turbomachinery 1997; 119(4): 820–830.

Eisenlohr

Chladek

. Thermal tip clearance control for centrifugal compressor of an APU engine. ASME J Turbomachinery 1994; 116(4): 629–634.

Jansen W. A method for calculating the flow in a centrifugal impeller when entropy gradients are present. In: Proceedings of royal society conference on internal aerodynamics (turbomachinery), Cambridge, England, 1967.

Musgrave DS. The prediction of design and off-design efficiency for centrifugal compressor impellers. In: Proceedings of 25th ASME gas turbine conference and 22nd annul fluids engineering conference, New Orleans, Performance Prediction of Centrifugal Pumps and Compressors, 1980, pp.185–189.

Goto

. Study of internal flows in a mixed-flow pump impeller at various tip clearances using three-dimensional viscous flow computations. ASME J Turbomachinery 1992; 114(2): 373–382.

Ishida

Senoo

Ueki

. Secondary flow due to the tip clearance at the exit of centrifugal impellers. ASME J Turbomachinery 1990; 112(1): 19–24.

10.

Schleer

Abhari

. Clearance effects on the evolution of the flow in the vaneless diffuser of a centrifugal compressor at part load condition. ASME J Turbomachinery 2008; 130(3): 031009–031009.

11.

Schleer

Song

Abhari

. Clearance effects on the onset of instability in a centrifugal compressor. ASME J Turbomachinery 2008; 130(3): 031002–031002.

12.

Dean

Jr Senoo

. Rotating wakes in vaneless diffuser. ASME J Basic Eng 1960; 82: 563–574.

13.

Eckardt D. Flow field analysis of radial and backswept centrifugal compressor impellers, Part 1: Flow measurement using a laser velocimeter. In: Proceedings of 25th ASME gas turbine conference and 22nd annul fluids engineering conference, New Orleans, Performance Prediction of Centrifugal Pumps and Compressors, 1980, pp.77–86.

14.

Brown WB. Friction coefficients in a vaneless diffuser. NACA TN 1311, 1947.

15.

Brown WB and Bradshaw GR. Method of designing vaneless diffusers and experimental investigation of certain undetermined parameters. NACA TN 1426, 1947.

16.

Stanitz JD. One-dimensional compressible flow in vaneless diffusers of radial and mixed-flow centrifugal compressors. NACA TN 2610, 1952.

17.

Johnston

Dean

Jr . Losses in vaneless diffusers of centrifugal compressors and pumps. ASME J Eng Power 1966; 88: 49–62.

18.

Japikse

. Advanced diffusion levels in turbocharger compressors and component matching. IMechE 1982; C45/82: 143–155.

19.

Japikse

. Centrifugal compressor design and performance , Vermont: Concepts ETI, 1996.

20.

Schleer

Hong

Zangeneh

. Investigation of an inversely designed centrifugal compressor stage – Part 2: Experimental investigations. ASME J Turbomachinery 2004; 126(1): 82–90.

21.

DIN 1952. Durchflussmessung mit Blenden, Düsen und Venturirohren in voll durchströmten Rohren mit Kresisquerschnitt , Berlin, Germany: Beuth Verlag GmbH, 1982.

22.

Kupferschmied

Koeppel

Roduner

. On the development and application of the fast-response aerodynamic probe system in turbomachines – Part 1: The measurement system. ASME J Turbomachinery 2000; 122(3): 505–516.

23.

Roduner

Kupferschmied

Koeppel

. On the development and application of the fast-response aerodynamic probe system in turbomachines – Part 2: Flow, surge, and stall in a centrifugal compressor. ASME J Turbomachinery 2000; 122(3): 517–526.

24.

Koeppel

Roduner

Kupferschmied

. On the development and application of the fast-response aerodynamic probe system in turbomachines – Part 3: Comparison of averaging methods applied to centrifugal compressor measurements. ASME J Turbomachinery 2000; 122(3): 527–536.

25.

Eckardt

. Instantaneous measurements in the jet-wake discharge flow of a centrifugal compressor impeller. ASME J Eng Power 1975; 97: 337–346.

26.

Johnson

Moore

. The development of wake flow in a centrifugal impeller. ASME J Eng Power 1980; 102: 382–390.

27.

Murakami

Kikuyama

Asakura

. Velocity and pressure distributions in the impeller passages of centrifugal pumps. ASME J Fluids Eng 1980; 102: 420–426.

28.

Cumpsty

. Compressor aerodynamics , Essex, England: Longman Science & Technical, 1989.