Intake grille design for an embedded ventilation-and-cooling system in an aircraft

Abstract

An inlet grille typically needs to be installed at the inlet of the air intake of the ventilation-and-cooling system embedded in airborne electronic equipment to improve pneumatic stealth performance. Here, a typical flying wing model is used as a case study, and a computational fluid dynamics (CFD) simulation is performed. The flow resistance characteristics of the air intake of the opening of the ventilation-and-cooling system on a flat fuselage surface with and without an inlet grille are analyzed at different flow rates and Mach 0.25. The effects of the grille opening shape, diversion angle, thickness, aperture size, and hole shape on the flow resistance characteristics are investigated in detail. The grille is found to effectively guide airflow entry: although the flow resistance at the inlet is increased, the flow resistance at the inlet and outlet of the air intake is significantly reduced. The optimal developments of the outflow and flow resistance characteristics are obtained for a quadrilateral opening. The smaller the diversion angle is, the smoother the airflow entry, and the higher the quality of the internal airflow. The rectification, viscous resistance, and weight exhibit opposing trends with increasing thickness and must be comprehensively considered in designing an optimal scheme. A large-aperture grille ensures good flow patency at low flow rates, whereas a small-aperture grille can reduce flow perturbations and separation at high flow rates by smoothly guiding air into the intake. A grille with round holes has a better spanwise and chordwise balancing effect on the airflow and better flow resistance characteristics than a grille with diamond-shaped holes.

Keywords

ventilation-and-cooling system air intake grille flow resistance computational fluid dynamics (CFD)

Get full access to this article

View all access options for this article.

References

Wang

Zhou

Yang

, et al. Experimental investigation of aircraft spray cooling system with different heating surfaces and different additives. Appl Therm Eng 2016; 103: 510–521.

Wang

. Exergy analysis of integrated TEG and regenerative cooling system for power generation from the scramjet cooling heat. Aerospace Science Technology 2017; 66: 12–19.

Shokri

Ebrahimi

. Heat transfer aspects of regenerative-cooling in methane-based propulsion systems. Aerospace Sci Tech 2018; 82–83: 412–424.

Akin

Kahveci

. An optimization study for rotorcraft avionics bay cooling. Aerospace Sci Tech 2019; 90: 1–11.

Chen

LiX

, et al. Pressure drop analysis and aerodynamic design of compressor L-inlet duct[J]. Aerospace Science Technology 2020; 107: 1–14.

Zheng

Tian

Qin

, et al. Effect of film cooling injection on aerodynamic performances of scramjet isolator [J]. Aerospace Science Technology 2019; 94: 1–12.

Liang

Guo

Zhao

. Effect of honeycomb on aerodynamic performance and radar cross section of inlet [J]. Acta Aeronauticaet Astronautica Sinica 1998; 9(5): 567–569.

Rumpf

Shippen

. Comparison of aerogrids and punched plates for smoothing flow from short annular diffusers[R]. NASA CR-120960, 1972.

Chiccine

Abdalla

. Experimental investigation of expanded duct sections and screens for reducing flow distortions at subsonic flows[R]. NASA MEMO 1-9-59E, 1959.

10.

Piercy

Klann

. Diffuser-exit total-pressure profiles for side-inlet model at mach3.05[R]. NASA RME55F24, 1955.

11.

Liang

Zhang

. An experimental investigation of the inlet exit flow field improved by aerodynamic grid[J]. J Propulsion Tech 1992; 2(1): 8–13.

12.

Chen

Zhou

, et al. Application of the perforated distribution plate in the LOX/kerosene staged combustion roctet engine[J]. J Rocket Propulsion 2007; 33(2): 1–6.

13.

Zhang

Zhou

. Electromagnetic scattering characteristics and experimental verification of inlet grille [J]. J Naning Univ Aeronautics Astronautics 2017; 49(3): 361–369.

14.

Rourke

. Air Force F-22 Fighter Program: Background and Issues for congress[R]. Congressional Research Service Reports, 2009.

15.

Shaughnessy

. F-35 Fighter Jet Program Moves forward[M]. Fort Worth Business Press, 2012.

16.

Nangia

Ghoreyshi

Van Rooij

MPC

, et al. Aerodynamic design assessment and comparisons of the MULDICON UCAV concept[J]. Aerospace Science Technology 2019; 93: 105321.

17.

Sousa

Wellons

. Results of Shipboard Relative GPS (SRGPS) Testing for the Pegasus X-47A Unmanned Combat Air Vehicle (UCAV)[J]. Proceedings of Annual Meeting of the Institute of Navigation & Cigtf Guidance Test Symposium, 2003, pp. 291–300.

18.

Menter

. Two-equation eddy-viscosity turbulence models for engineering applications. AIAA J 1994; 32(8): 1598–1605.

19.

Jagan

Terjesen

Summerfelt

. Influence of inlet and outlet placement on the hydrodynamics of culture tanks for Atlantic salmon[J]. Int J Mech Sci 2020; 188: 1–22.

20.

Tian

Wang

, et al. Drag reduction performance and mechanism of a thermally conductive elastic wall in internal flow[J]. Appl Therm Eng 2017; 123.

21.

Zhan

. Numerical simulation on rigid foreign object exclusion in the turboprop engine intake system with a bypass duct. IEEE ACCESS 2019; 7: 61920–61933.

22.

Tinddell

Hill

. CFD analysis of the X-29 inlet at high angle of attack[J]. J Aircraft 2015; 30(4): 480–487.

23.

Zhan

Wang

Zhang

, et al. Experimental research on improving ECM accuracy and stability for diamond-hole grilles[J]. Proced CIRP 2018; 68: 684–689.

24.

Kim

, et al. Grille design for passenger car to improve aerodynamic and cooling performance using CFD technique. Int.J Automot Technol 2016; 17(6): 967–976.

25.

Zhao

J S

Wang

Liu

, et al. Flow field design and process stability in electrochemical machining of diamond holes [J]. Chin J Aeronautics 2016; 29(6): 1830–1839.

26.

Zhang

Zhou

. Aerodynamic and stealthy integrated performance of conformal inlet coupling entrance grille of flying wing unmanned aerial vehicle [J]. J Aerospace Power 2018; 33(7): 1612–1621, (in Chinese).