Blade tip clearance is a critical engine health parameter measured on gas turbines. Increase in tip clearance results in decreased efficiency, whereas with decrease in clearance due to thermal and centrifugal loads, rotor blades might rub the engine case. Various sensing techniques are being used, among them, capacitance-based systems are widely used by many engine houses. Among the capacitance conditioning circuits, resistor-capacitor series network-based circuits are simple to implement but pose many challenges during practical development. During the current work, the authors have designed a novel capacitance conditioning circuit combining resistor-capacitor series network, instrumentation amplifiers, and direct current–direct current converters. Performance of the developed capacitance conditioning electronics was evaluated through lab testing and tip clearance measurement on fan stage of an aero gas turbine engine. The prototype conditioner circuit has efficiently conditioned and resolved small capacitances varying from 1.25 pF to 0.00413 pF for running clearances between 0.4 mm and 3 mm, respectively. The developed electronics produced high output with signal-to-noise ratio of 58.1 dB, resolution of 2.5 µm, bandwidth of about 700 kHz, and an accuracy of about 98%. This development has culminated towards miniaturization of the total electronics and has the potential to get developed as smart capacitance sensor. This paper explains the practical aspects and challenges involved while designing and developing such practical conditioning circuits.
Amsbury CR and Chivers JWH. Systems for the measurement of rotor tip clearance and displacement in a gas turbine. In: AGARD-237, Propulsion and Energetics Panels 51st (B) Specialists Meeting, seal technology in gas turbine engines, London, England, 6–7 April 1978.
PfisterTBüttnerLCzarskeJ, et al.Turbo machine tip clearance and vibration measurements using a fibre optic laser Doppler position sensor. Meas Sci Technol2006; 17: 1693–1705.
4.
Maslovskiy A, Bakulin M and Snitko M. Microwave blade tip clearance measurements: Principles, current practices and future opportunities. In: ASME Proceedings of ASME turbo expo 2012, Copenhagen, Denmark, 11–15 June 2012, Paper GT2012-69201.
5.
Tagashira T, Sugiyama N, Matsuda N, et al. Measurement of blade tip clearance using an ultrasonic sensor. In: Proceedings of the 35th AIAA aerospace sciences meeting and exhibit, Reno, NV, 6–9 January 1997, AIAA Paper 97-0165.
6.
HallLCJonesBE. An investigation into the use of a cone-jet sensor for clearance and eccentricity measurement in turbomachinery. Proc Inst Mech Eng1976; 190: 23–30.
7.
Hastings MM and Jensen HB. A novel proximity probe unaffected by shaft electromagnetic properties. In: International Gas Turbines and Aeroengine Congress & Exhibition, Birmingham, UK, 10–13 June 1996, ASME Paper 96-GT-004.
8.
Tomassini R, Rossi G and Brouckaert J-F. Blade tip clearance and blade vibration measurements using a magnetoresistive sensor. In: Proceedings of 11th European conference on turbomachinery fluid dynamics & thermodynamics, Madrid, Spain, 23–27 March 2015.
9.
Kwapisz D, Hafner M and Queloz S. Calibrations and characterization of a CW radar for blade tip clearance measurement. In: Proceedings of 7th European radar conference, Paris, France, 30 September–1 October, 2010, pp.320–323. Piscataway, NJ: IEEE.
10.
Dooley KA. Capacitive bridge type probe for measuring blade tip clearance. US Patent 4,818,948, USA, 1989.
11.
Barranger JP. An in-place calibration technique to extend the temperature capability of capacitance sensor system. In: Proceedings of Society of Automotive Engineers Aerospace Meeting, San Diego, CA, 27–30 November 1978, SAE Paper 781 003.
12.
Demers RN. Compressor blade clearance measurement using capacitance and phase lock techniques. In: AGARD advanced instrumentation aero engine components, Philadelphia, PA, 19–23 May 1986.
13.
Chivers J. A technique for the measurement of blade tip clearance in a gas turbine. In: Proceedings of 25th joint propulsion conference, Monterey, CA, 10–12 July 1989, AIAA 89-2916.
14.
Barranger JP. Low-cost FM oscillator for capacitance type of blade tip clearance measurement system. NASA Technical Paper 2746, July 1987. Cleveland, OH: NASA Lewis Research Center.
15.
SarmaGRBarrangerJP. Capacitance-type blade-tip clearance measurement system using a dual amplifier with ramp/DC inputs and integration. IEEE Trans Instrum Meas1992; 41: 674–678.
16.
HuangSGreenRGPlaskowskiA, et al.A high frequency stray-immune capacitance transducer based on the charge transfer principle. IEEE Trans Instrum Meas1988, pp. 368–373.
17.
Marioli D, Sardini E and Taroni A. Measurement of small capacitance variations. In: Conference on precision electromagnetic measurements, Ottawa, Canada, 11–14 June 1990. Piscataway, NJ: IEEE.
18.
HuangSMXieCGThornR, et al.Design of sensor electronics for electrical capacitance tomography. IEEE Proc G1992; 139: 83–88.
19.
YangWQScottALBeckMS. High frequency and high resolution capacitance measuring circuit for process tomography. IEEE Proc Circuits Devices Syst1994; 141: 215–219.
20.
Heep JJ and Curtis DR. Battery operated capacitance measurement circuit. US Patent 5294889, USA, 1994.
21.
WangWQ. A self-balancing circuit to measure capacitance and loss conductance for industrial transducer applications. IEEE Trans Instrum Meas1996; 45: 955–958.
22.
AshrafiAGolnabiH. A high precision method for measuring very small capacitance changes. Rev Sci Instrum1999; 70: 3483–3487.
23.
Rerkratn A, Lertpakdee T, Chitsakul K, et al. Small capacitance measuring circuit for capacitive sensors. In: International Conference on Control Robotics Society, Gyeongyu, Korea, 22–25 October 2003, ICCAS2003, pp.483–486.
24.
Baglio S, Castorina S, Ganci G, et al. A high sensitivity conditioning circuit for capacitive sensors including stray effects compensation and dummy sensors approach. In: Proceedings of the 21st IEEE instrumentation and measurement technology conference, Como, Italy, 18–20 May 2004, pp.1542–1545. Piscataway, NJ: IEEE.
25.
IgnjatovicZBockoMF. An interface circuit for measuring capacitance changes based upon capacitance-to-duty cycle (CDC) converter. IEEE Sens J2005; 5: 403–410.
26.
Kim JM. Capacitance measurement method employing floating gate of semiconductor device. US Patent 7751995 B2, USA, 2010.
27.
Hasse WC and Roberge JK. Clearance measurement system. US Patent 5723980, USA, 1998.
28.
Holmberg P. Automatic balancing of linear AC bridge circuits for capacitive sensor elements. IEEE Trans Instrum Meas 1995; 44: 803–-805.
29.
MohanNMKumarVJ. Novel signal conditioning circuit for push-pull type capacitive transducers. IEEE Trans Instrum Meas2007; 56: 153–157.
30.
Drumm M and Haase WC. High performance rotor health monitoring. In: 19th digital avionics systems conference 2000, pp.6.E.4-1–6.E.4–7. Piscataway, NJ: IEEE.
31.
SteinerA. Techniques for blade tip clearance measurements with capacitive probes. Meas Sci Tech2000; 11: 865–869.
32.
SatishTNMurthyRSinghAK. Analysis of uncertainties in measurements of rotor blade tip clearance in gas turbine engine under dynamic condition. Proc IMechE, Part G: J Aerospace Engineering2014; 228: 652–670.
33.
Muller D, Sheard AG, Mozumdar S, et al. Capacitive measurement of compressor and turbine blade tip to casing running clearance. In: International Gas Turbine and Aeroengine Congress & Exhibition, Birmingham, UK, 10–13 June 1996, ASME 96-GT-349.
34.
SatishTNRaoANVNambiarAS, et al.Investigation into the development and testing of a simplex capacitance sensor for rotor tip clearance measurement in turbo machinery. Exp Tech2018; 42: 575–592. .
35.
Bailleul GD and Albijat S. Review of progress in the development of capacitive sensors for blade tip clearance measurement. In: Proceedings of ASME turbo Asia conference, Jakarta, Indonesia, 5–7 November 1996, ASME Paper 96-TA-1.
36.
Pritchard E, Md Mahfouz, Evans III B, et al. Flexible capacitive sensors for high resolution pressure measurement. In: IEEE sensors 2008 conference, Lecce, Italy, 26–29 October, 2008, pp.1484–1487. Piscataway, NJ: IEEE.
37.
Wang D. Capacitive proximity sensing using the FDC1004. Application Report, Texas Instruments Incorporated, USA, April 2015.
38.
Lion Precision. Understanding sensor resolution specifications and performance. TechNote LT05-0010, September 2014. St. Paul, MN: Lion Precision.
39.
Lion Precision. Capacitive sensor operation and optimization. TechNote LT03-0020, November 2015. St. Paul, MN: Lion Precision.
40.
Precision Instrumentation Amplifier AD624, Analog Devices, 1999.
41.
Razavi B. Design of analog CMOS integrated circuits. New York, NY: McGraw-Hill, 2001.
42.
Hunt S. Noise analysis in precision analog designs. Wilmington, MA: Analog Devices, 2016.
