Experimental study on axially non-uniform clearances in a linear turbine cascade with a cavity squealer tip

Abstract

The effects of axially non-uniform clearances on the tip leakage flow and aerodynamic performance in a linear turbine cascade with a cavity squealer tip were investigated in this study with the objective of improving the flow loss and tip flow field structure. A calibrated five-hole probe was used for the measurement of three-dimensional flows downstream of the cascade. The method of oil-flow visualization was used to show the endwall flow field structure. The distribution of endwall static pressure was measured particularly by using the special moveable endwall. The axially non-uniform clearance, as a novel strategy that has a non-negligible influence on tip clearance flow and clearance leakage loss, may become a potential technology for improving aerodynamic performance in turbine cascades. By using the expanding clearance, the flow loss at the outlet is reduced effectively and an apparent improvement of aerodynamic performance in the turbine cascade is gained. Under the tip clearances of 0.75% H and 2% H, the maximum reduction of overall total pressure loss coefficient at the outlet is separately about 2.3% and 3.5% compared with the uniform clearance. The shrinkage of the buffer zone is considered to be able to weaken the interaction of the tip leakage vortex and passage vortex and thus reduce the loss of passage vortex. For the shrinking clearance, a noticeable decline in the aerodynamic performance of turbine cascade with cavity squealer tip is exhibited at both on and off design conditions in contrast to the uniform clearance. In addition, the effects of axially non-uniform clearances on the aerodynamic performance at off-design conditions have been investigated.

Keywords

Axially non-uniform clearance cavity squealer tip tip leakage flow aerodynamic performance linear turbine cascade

Get full access to this article

View all access options for this article.

References

Hourmouziadis J and Albrecht G. An integrated aero/mechanical performance approach to high technology turbine design. Motoren-und Turbinen-Union GMBH Munich Germany FR, ADP006200, 1987.

Bindon JP. Pressure distributions in the tip clearance region of an unshrouded axial turbine as affecting the problem of tip burnout. ASME Paper 87-GT-230, 1987.

Bindon

Morphis

. The development of axial turbine leakage loss for two profiled tip geometries using linear cascade data. ASME J Turbomach 1992; 114: 198–203.

Willinger R and Haselbacher H. On the modeling of tip leakage flow in axial turbine blade rows. ASME Paper 2000-GT-0633, 2000.

Bindon

. The measurement and formation of tip clearance loss. ASME J Turbomach 1989; 111: 257–263.

Morphis G and Bindon JP. The effects of relative motion, blade edge radius and gap size on the blade tip pressure distribution in an annular turbine cascade with clearance. ASME Paper 88-GT-256, 1988.

Dey D and Camci C. Aerodynamic tip desensitization of an axial turbine rotor using tip platform extensions. ASME Paper 2001-GT-0484, 2001.

Heyes

FJG

Hodson

. Measurement and prediction of tip clearance flow in linear turbine cascades. ASME J Turbomach 1993; 115: 376–382.

Yamamoto

. Interaction mechanisms between tip leakage flow and the passage vortex in a linear turbine rotor cascade. ASME J Turbomach 1988; 110: 329–338.

10.

Tallman J and Lakshminarayana B. Numerical simulation of tip leakage flows in axial flow turbines, with emphasis on flow physics: part I—effect of tip clearance height. ASME Paper 2000-GT-0514, 2000.

11.

Booth

Dodge

Hepworth

. Rotor-tip leakage part I-basic methodology. J Eng Gas Turbines Power 1982; 104: 154–161.

12.

Chan JKK, Yaras MI and Sjolander SA. Interaction between inlet boundary layer, tip-leakage and secondary flows in a low-speed turbine cascade. ASME Paper 94-GT-250, 1994.

13.

Mischo

Behr

Abhari

. Flow physics and profiling of recessed blade tips: impact on performance and heat load. ASME J Turbomach 2008; 130: 021008–021008-8.

14.

Maral H, Senel CB and Kavurmacioglu LA. Parametric and computational aerothermal investigation of squealer tip geometry in an axial turbine: a parametric approach suitable for future advanced tip carving optimizations. ASME Paper GT2016-58107, 2016.

15.

Volino

. Control of tip leakage in a high-pressure turbine cascade using tip blowing. ASME J Turbomach 2017; 139: 061008–061008-12.

16.

Heyes

FJG

Hodson

Dailey

. The effect of blade tip geometry on the tip leakage flow in axial turbine cascades. ASME J Turbomach 1992; 114: 643–651.

17.

Ameri

Steinthorsson

Rigby

. Effect of squealer tip on rotor heat transfer and efficiency. ASME J Turbomach 1998; 120: 753–759.

18.

Schabowski

Hodson

. The reduction of over tip leakage loss in unshrouded axial turbines using winglets and squealers. ASME J Turbomach 2013; 134: 041001–041001-11.

19.

Lee

Kim

. Tip gap height effects on the aerodynamic performance of a cavity squealer tip in a turbine cascade in comparison with plane tip results: part 1—tip gap flow structure. Exp Fluids 2010; 49: 1039–1051.

20.

Lee

Choi

. Tip gap height effects on the aerodynamic performance of a cavity squealer tip in a turbine cascade in comparison with plane tip results: part 2—aerodynamic losses. Exp Fluids 2010; 49: 713–723.

21.

Mohan K and Guruprasad SA. Effect of axially non-uniform rotor tip clearance on the performance of a high speed axial flow compressor stage. ASME Paper 94-GT-479, 1994.

22.

Wang

Jia

Cai

. Influence of blade tip clearance shapes on aerodynamic performance of an axial flow compressor stator. Proc IMechE, Part A: J Power and Energy 2002; 216: 395–401.

23.

. Effects of axial non-uniform tip clearances on aerodynamic performance of a transonic axial compressor. J Therm Sci 2008; 17: 331–336.

24.

Batabyal P, Alone DB and Maharana SK. Numerical studies on effect of stepped tip clearance height on the performance of single stage transonic axial flow compressor. ASME Paper GTINDIA2013-3722, 2013.

25.

. Cantilevered stator hub leakage flow control and loss reduction using non-uniform clearances. Aerosp Sci Technol 2016; 51: 1–10.

26.

Gao

Zheng

et al.

Effect of axially non-uniform rotor tip clearance on aerodynamic performance of an unshrouded axial turbine. Proc IMechE, Part A: J Power and Energy 2011; 226: 231–244.

27.

Zhou

Chen

Wang

. Unsteady study of winglet cavity tip on leakage flow in a high pressure turbine stage of low-aspect ratio. Proc IMechE, Part C: J Mechanical Engineering Science 2018; 232: 3708–3721. DOI: 10.1177/0954406217741517.

28.

Zhou

Chen

Wang

. Aerodynamic optimisation of a winglet-cavity tip in a high-pressure axial turbine cascade. Proc IMechE, Part G: J Aerospace Engineering 2018; 232: 649–663. DOI: 10.1177/0954410016683735.