Experimental investigation on the performance of compressor cascade using blended-blade-end-wall contouring technology

Abstract

Three-dimensional flow separations commonly occur in the corner region formed by the blade suction surface and end wall in compressors. How to control or reduce these separations is a vital problem for aerodynamic designers all the time. Blended blade and end wall contouring technology has been proposed to control flow separation for several years and validated in many cases using the numerical method, but experimental data was not obtained so far. So in this paper, the baseline cascade scaling from the NACA65 airfoil with 42° turning angle is designed, tested, and analyzed firstly. Then, based on the experimental results of the baseline cascade, blended blade and end wall contouring is applied to the suction surface and hub corner region of the baseline cascade and the detailed experiment is carried out. The results show that the blended blade and end wall contouring technology can decrease the total pressure loss by 8% and 7% at 0° and +10° incidence angles separately. The improved span range mainly focuses on the 10–25% span height. The rolling change of the passage vortex influenced by the accumulation of low energy fluid driven by cross flow in the hub corner should be the main reason for the performance improvement.

Keywords

Flow separation control corner region compressor cascade experiment blended blade and end wall

Get full access to this article

View all access options for this article.

References

Denton

. Loss mechanisms in turbomachines. J Turbomach 1993; 115: 621–621.

Lei

Spakovszky

Greitzer

. A criterion for axial compressor hub-corner stall. J Turbomach 2008; 130: 31006–31006.

Haller

Lovblad

Giannakopoulos

et al.

Multivariate pattern recognition for diagnosis and prognosis in clinical neuroimaging: State of the Art, current challenges and future trends. Brain Topogr 2014; 27: 329–337.

Horlock

Louis

Percival

PME

et al.

Wall stall in compressor cascades. J Fluids Eng 1966; 88: 637–648.

Dong

Gallimore

Hodson

. Three-dimensional flows and loss reduction in axial compressors. J Turbomach 1987; 109: 354–361.

Gbadebo

Cumpsty

Hynes

. Three-dimensional separations in axial compressors. J Turbomach 2005; 127: 331–331.

Weingold

Neubert

Behlke

et al.

Bowed stators: An example of CFD applied to improve multistage compressor efficiency. J Turbomach 1997; 119: 161–168.

Fischer

Riess

Seume

. Performance of strongly bowed stators in a four-stage high-speed compressor. J Turbomach 2004; 126: 333–338.

Tweedt DL and Okiishi TH. Stator blade row geometry modification influence on two-stage compressor aerodynamic performance. Technical Report, Iowa State University, USA, 1983.

10.

Wadia AR. Some advances in fan and compressor aero at GE aircraft engines. 2005.

11.

Guümmer

Wenger

Kau

. Using sweep and dihedral to control three-dimensional flow in transonic stators of axial compressors. Trans ASME, J Turbomach 2001; 123: 40–48.

12.

Barankiewicz W and Hathaway M. Impact of variable-geometry stator hub leakage in a low speed axial compressor. New York: ASME, 1998, p. 194.

13.

Dorfner C, Nicke E and Christian V. Axis-asymmetric profiled endwall design by using multiobjective optimisation linked with 3D RANS-flow-simulations. In: ASME conference proceedings, vol. 2007, 2007, pp.107–114.

14.

Harvey NW. Some effects of non-axisymmetric end wall profiling on axial flow compressor aerodynamics: Part I—Linear cascade investigation. In: ASME turbo expo 2008: Power for land, sea, and air, Vol 6: Turbomachinery, Parts A, B, C, 2008, pp.543–555.

15.

Shi

Liu

et al.

Experimental investigation of a counter-rotating compressor with boundary layer suction. Chinese J Aeronaut 2015. (May): 1–11.

16.

Semiu Gbadebo

Nicholas Cumpsty

Tom Hynes

. Control of three-dimensional separations in axial compressors by tailored boundary layer suction. J Turbomach 2008; 130: 11004–11004.

17.

Zhou

et al.

Control of the corner separation in a compressor cascade by steady and unsteady plasma aerodynamic actuation. Exp Fluids 2010; 48: 1015–1023.

18.

Zhao

et al.

Numerical investigation of flow separation control on a highly loaded compressor cascade by plasma aerodynamic actuation. Chinese J Aeronaut 2012; 25: 349–360.

19.

Debruge

. The aerodynamic significance of fillet geometry in turbocompressor blade rows. J Eng Power 1980; 102: 984–993.

20.

Ralf M, Konrad V, Helmut S, et al. Endwall boundary layer control in compressor cascades. In: ASME conference proceedings, 2004, pp.427–435.

21.

Ji LC, Shao WW, Yi WL, et al. A model for describing the influences of SUC-EW dihedral angle on corner separation. In: ASME conference proceedings, 2007, pp.219–228.

22.

JI LC, Yi WL and Tian Y. A method of designing blended blade and endwall for turbomachinery. ZL201010623606.2, 2012.

23.

Ji L, Tian Y, Li W, et al. Numerical studies on improving performance of rotor-67 by blended blade and endwall technique. In: ASME turbo expo 2012: Turbine technical conference expo GT 2012, 2012, pp.135–145.

24.

Chen

. Study on blended blade and endwall technique applied to centrifugal compressor. J Eng Thermophys 2014; 35: 256–261.

25.

W-L

Chen

Z-M

et al.

Investigation on application of blended blade and endwall technique on radial diffuser. J Eng Thermophys 2015; 36: 1–5.

26.

Han

Zhong

. Experimental investigation on interaction between tip clearance flow and three-dimensional separation in compressor cascade. J Propul Technol 2013; 2: 187–193.