Multi-objective optimization of lean and sweep angles for stator and rotor blades of an axial turbine

Abstract

The axial turbine is one of the most challenging components of gas turbines for industrial and aerospace applications. With the ever-increasing requirement for high-aerodynamic performance blades, three-dimensional aerodynamic shape optimization is of great importance. In this research, the rear part of a gas turbine consisting of a one-stage axial turbine is optimized numerically. A useful optimization algorithm is presented to improve the efficiency and/or pressure ratio of the axial turbine with two different objective functions. The three-dimensional blade-shape optimization is employed to study the effects of the turbine stator and rotor lean and sweep angles on the turbine performance. The investigation is carried out at the turbine design speed. By coupling a verified computational fluid dynamics simulation code with the genetic algorithm, an automated design procedure is prepared. Geometry candidates for the optimization algorithm are generated by re-stacking of the two-dimensional airfoil sections. Three-dimensional, turbulent, and compressible flow field is numerically investigated via a Navier–Stokes solver to calculate various objective functions. Experimental results of the gas turbine are used for specifying the boundary conditions and validation of the simulation results. The proposed method results in 1.3% and 1.5% improvements in the turbine stage efficiency in design speed and reduced mass parameter at choke condition, respectively.

Keywords

Axial turbine lean optimization rotor stator sweep

Get full access to this article

View all access options for this article.

References

Rezasoltani M, Schobeiri MT and Han JC. Experimental investigation of the effect of purge flow on film cooling effectiveness on a rotating turbine with non-axisymmetric endwall contouring. In: ASME turbo expo, San Antonio, Texas, USA, June 3–7, 2013, GT2013-94807.

Pierret S. Multi-objective and multi-disciplinary optimization of three-dimensional turbo-machinery blades. In: Proceedings of the 6th world congresses of structural and multidisciplinary optimization, 2005.

Arabnia M and Ghaly W. A strategy for multi-point shape optimization of turbine stages in three-dimensional flow. In: Proceeding of ASME turbo expo, Orlando, Florida, USA, 2009, GT2009-59708.

Arabnia M and Ghaly W. On the use of blades stagger and stacking in turbine stage optimization. In: Proceeding of ASME turbo expo, Glasgow, UK, 2010, GT2010-23399.

Arabnia M, Sivashanmugam VK and Ghaly W. Optimization of an axial turbine rotor for high aerodynamic inlet blockage. ASME paper GT2011-46757, 2011.

Sivashanmugam VK, Arabnia M and Ghaly W. Aero-structural optimization of an axial turbine stage in three-dimensional flow. ASME paper GT2010-23406, 2010.

Oyama A, Liou MS and Obayashi S. Transonic axial-flow blade shape optimization using evolutionary algorithm and three-dimensional Navier-Stokes solver. vol. 4. Citeseer, 2002.

Luo C, Song L, Li J, et al. Multi-objective optimization approach to multidisciplinary design of a three-dimensional transonic compressor blade. ASME paper GT2009-59982, 2009.

Okui H, Verstraete T, van den Braembussche RA, et al. Three dimensional design and optimization of a transonic rotor in axial flow compressors. ASME paper GT2011-45425, 2011.

10.

Benini

. Three-dimensional multi-objective design optimization of a transonic compressor rotor. J Propul Power 2004; 20: 559–565.

11.

Taghavi-Zenouz

Afzali

. Preliminary design optimization of profile losses in multi-stage axial compressors based on complex method. Proc IMechE, Part G: J Aerospace Engineering 2008; 222: 951–961.

12.

Nili-Ahmadabadi M, Durali M and Hajilouy-Benisi A. A novel quasi 3-d design method for centrifugal compressor meridional plane. ASME paper GT2010-23341, 2010.

13.

Kim JH, Choi JH and Kim KY. Design optimization of a centrifugal compressor impeller using radial basis neural network method. ASME paper GT2009-59666, 2009.

14.

Lotfi O, Teixeira J, Ivey P, et al. Shape optimization of axial fan blades using genetic algorithms and a 3D Navier-Stokes solver. ASME paper GT2006-90659, 2006.

15.

Jin H. Design of a highly loaded transonic two-stage fan using swept and bowed blading. ASME paper GT2011-45988, 2011.

16.

Yershov

Rusanov

Shapochka

. Shape optimization of two turbine stages using the deformed polyhedron method and a three-dimensional RANS solver. Proc IMechE, Part A: J Power and Energy 2002; 216: 203–213.

17.

Wang D and Li Y. 3D direct and inverse design using NS equations and the adjoint method for turbine blades. ASME paper GT2010-22049, 2010.

18.

Lampart

. Numerical optimization of a high pressure steam turbine stage. J Comput Appl Mech 2004; 5: 311–321.

19.

Yuan X, Tanuma T, Zhu X, et al. A CFD approach to fluid dynamic optimum design of steam turbine stages with stator and rotor blades. ASME paper GT2010-22477, 2010.

20.

Arabnia M. Aerodynamic shape optimization of axial turbines in three dimensional flow. PhD Thesis, Concordia University, Montreal, Quebec, 2012.

21.

Moustapha H, Zelesky MF, Baines NC, et al. Axial and radial turbines. Concepts NREC, 2003.

22.

Van den Braembussche

. Numerical optimization for advanced turbomachinery design: optimization and computational fluid dynamics 2008, pp. 147–189.

23.

Büche D, Guidati G and Stoll P. Automated design optimization of compressor blades for stationary, large-scale turbomachinery. ASME paper GT2003-38421, 2003.

24.

Wilcox

. Turbulence modeling for CFD 1998; vol. 2, pp. La Canada, CA: DCW Industries.

25.

Menter

. Two-equation Eddy-viscosity turbulence models for engineering applications. AIAA J 1994; 32: 1598–1605.

26.

Karrabi H, Pourfarzaneh H and Hajilouy-Benisi A. Zero D and 3D analysis of the centrifugal compressor of a gas turbine and its evaluation using experimental results. In: Proceedings of international mechanical engineering congress and exposition, ASME, 2011.