Wire Arc Additive Manufacturing (WAAM) is an emerging three-dimensional fabrication technology that enables higher deposition rate, material savings, and near net-shape. In this study, various shielding gas concentration (SGC) of argon (Ar) and carbon-di-oxide (CO2) was employed to fabricate 316L using Cold Metal Transfer (CMT) WAAM process. Microstructure characteristics and mechanical properties of thick-walled parts were studied. Microstructure studies show a combination of columnar and equiaxed grains in various regions. Microhardness results exhibit the uneven distribution of hardness value from bottom to top region along the building direction and the values are ranging between185 and 240 HV. Tensile studies indicates the both horizontal and vertical direction samples secures the higher ultimate tensile strength (UTS), yield strength (YS) and elongation (EL) values and confirmed the isotropic properties. Fractography studies prove ductile fracture with the evidence of dimples and enough plastic deformation. From the experimental results, the SGC-2 possesses finer solidification structure and higher mechanical properties than the other samples. The as-fabricated WAAM parts possess higher mechanical properties than the 316L parts fabricated via casting and wrought parts.
WongKVHernandezA. A review of additive manufacturing. ISRN Mech Eng2012; 1: 1–10.
2.
MehrpouyaMDehghanghadikolaeiAFotovvatiB. The potential of additive manufacturing in the smart. Appl Sci2019; 9: 3865.
3.
JavaidMHaleemASinghRP, et al.Role of additive manufacturing applications towards environmental sustainability. Adv Ind Eng Polym Res2021; 4: 312–322.
4.
CostelloSCACunninghamCRXuF, et al.The state-of-the-art of wire arc directed energy deposition (WA-DED) as an additive manufacturing process for large metallic component manufacture. Int J Comput Integr Manuf2023; 36: 469–510.
5.
SinghSRKhannaP. Wire arc additive manufacturing (WAAM): a new process to shape engineering materials. Mater Today Proc2021; 44: 118–128.
6.
OzelTShokriH. A review on wire-fed directed energy deposition based metal additive manufacturing. J Manuf Mater Proc2023; 7: 45.
7.
GowthamanPSJeyakumarSSarathchandraDT. Influence of heat input on microstructure and mechanical behaviour of austenitic stainless steel 316L processed in wire and arc additive manufacturing. Proc Inst Mech Eng Part E J Process Mech Eng2023; 237: 149–161.
8.
JafariDVanekerTHJGibsonI. Wire and arc additive manufacturing: opportunities and challenges to control the quality and accuracy of manufactured parts. Mater Des2021; 202: 109471.
9.
JinWZhangCJinS, et al.Wire arc additive manufacturing of stainless steels: a review. Appl Sci2020; 10: 1563.
10.
GradlPTinkerDCParkA, et al.Robust metal additive manufacturing process selection and development for aerospace components. J Mater Eng Perform2022; 31: 6013–6044.
11.
DinovitzerMChenXLaliberteJ, et al.Effect of wire and arc additive manufacturing (WAAM) process parameters on bead geometry and microstructure. Addit Manuf2019; 26: 138–146.
12.
KoliYYuvarajNSivanandamA, et al.Control of humping phenomenon and analyzing mechanical properties of Al–Si wire-arc additive manufacturing fabricated samples using cold metal transfer process. Proc Inst Mech Eng Part C J Mech Eng Sci2022; 236: 984–996.
13.
OrtegaAGGalvanLCMezragB. Effect of process parameters on the quality of aluminium alloy Al5Si deposits in wire and arc additive manufacturing using a cold metal transfer process. Sci Technol Weld Join2017; 23: 1–17.
14.
SelviSVishvaksenanARajasekarE. Cold metal transfer (CMT) technology—an overview. Def Technol2018; 14: 28–44.
15.
KumarNPSreedharGKumarSM, et al.Microstructure and electrochemical evaluation of ER-308L weld overlays on AISI 321 stainless steel for repair applications. Proc Inst Mech Eng Part E J Process Mech Eng2022; 238: 441–450.
16.
SinghR. Welding, corrosion-resistant alloys-stainless steel. In: Applied welding engineering third edition processes, codes and standards. UK: Elsevier, 2020.
17.
HaghdadiNLalehMMoyleM, et al.Additive manufacturing of steels: a review of achievements and challenges. J Mater Sci2021; 56: 64–107.
18.
JenaGAnandkumarBSofiaS, et al.Fabrication of silanized GO hybrid coating on 316L SS with enhanced corrosion resistance and antibacterial properties for marine applications. Surf Coatings Technol2020; 402: 126295.
19.
MurphyABTanakaMTashiroS, et al.A computational investigation of the effectiveness of different shielding gas. J Phys D Appl Phys2009; 42: 115205.
20.
MoinuddinSQSharmaA. Arc stability and its impact on weld properties and microstructure in anti-phase synchronised synergic-pulsed twin-wire gas metal arc welding. J Mater2015; 67: 293–302.
21.
CunatP. The welding of stainless steels. In: Materials and application series. 3. Luxembourg: Euro Inox, 2007.
22.
ElmerJWVajaJCartlonHD, et al.The effect of Ar and N2 shielding gas on laser weld porosity in steel, stainless steels, and nickel. Weld J2015; 94: 313–325.
23.
SilwalBNyczAMasuoCJ, et al.An experimental investigation of the effectiveness of Ar-CO2 shielding gas mixture for the wire arc additive process. Int J Adv Manuf Technol2020; 108: 1285–1296.
24.
MingGXiaoyanZQianwuH. Effects of gas shielding parameters on weld penetration of CO2 laser-TIG hybrid welding. J Mater Process Technol2007; 184: 177–183.
25.
YamaguchiMKomataRFurumotoT, et al.Influence of metal transfer behavior under Ar and CO2 shielding gases on geometry and surface roughness of single and multilayer structures in GMAW-based wire arc additive manufacturing of mild steel. Int J Adv Manuf Technol2022; 119: 911–926.
26.
AsgharMHPlacidoFNaseemS, et al.Characterization of reactively evaporated TiO2 thin films as high. Eur Phys J Appl Phys2006; 184: 177–184.
27.
RheeSKannatey-AsibuE. Observation of metal transfer during gas metal arc welding A high-speed analyzer and arc shadow-graphing system are used to better understand modes of metal transfer. Weld J1992; 71: 381–387.
28.
OkagawaRKDixonRDOlsonDL. The influence of nitrogen from welding on stainless steel weld metal microstructures. Am Weld Soc1983.
29.
SilwalBPudasainiNRoyS, et al.Altering the supply of shielding gases to fabricate distinct geometry in GMA additive manufacturing. Appl Sci2022; 12: 3679.
30.
SimõesGJoséTEsmerioA. GMA welding metal transfer mode study by high—speed imaging and electrical signal acquisition. J Brazilian Soc Mech Sci Eng2019; 8: 1–12.
31.
MarefatFKapilAArefS, et al.Evaluating shielding gas-filler wire interaction in bi-metallic wire arc additive manufacturing (WAAM) of creep resistant steel-stainless steel for improved process stability and build quality. J Manuf Process2023; 88: 110–124.
32.
AkbarzadehEYurtışıkKGürCH, et al.Influence of shielding gas on the microstructure and mechanical properties of duplex stainless steel in wire arc additive manufacturing. Met Mater Int2024; 30: 1977–1996.
33.
YangGDengFZhouS, et al.Influence of shielding gas nitrogen content on the microstructure and mechanical properties of Cu-reinforced maraging steel fabricated by wire arc additive manufacturing. Mater Sci Eng A2022; 832: 142463.
34.
PavanARChandrasekarNArivazhaganB, et al.Study of arc characteristics using varying shielding gas and optimization of activated-tig welding technique for thick AISI 316L (N) plates. CIRP J Manuf Sci Technol2021; 35: 675–690.
35.
GunnRN. 9-Welding processes, in duplex stainless steels. Cambridge: Woodhead Publishing, 1997, pp. 133–145.
DingJColegrovePMehnenJ, et al.Thermo-mechanical analysis of wire and arc additive layer manufacturing process on large multi-layer parts. Comput Mater Sci2011; 50: 3315–3322.
40.
YangfanWXizhangCChuanchuS, et al.Microstructure and mechanical properties of Inconel 625 fabricated by wire-arc additive manufacturing. Surf Coatings Technol2019; 374: 116–123.
41.
ChenXLiJChengX, et al.Microstructure and mechanical properties of the austenitic stainless steel 316L fabricated by gas metal arc additive manufacturing. Mater Sci Eng A2017; 703: 567–577.
42.
DeLongWT. Ferrite in austenitic stainless steel. Weld metal-2. Indian Weld J1975; 7: 75–83.
43.
InoueH. Clarification of solidification behaviors in austenitic stainless steels based on welding process. Nippon Steel Tech Rep2007; 95: 62–70.
44.
BelsvikMATuchoWMHansenV, et al.Microstructural studies of direct-laser-deposited stainless steel 316L-Si on 316L base material. SN Appl Sci2020; 2: 1967.
45.
BolzoniLXiaMBabuNH, et al.Formation of equiaxed crystal structures in directionally solidified Al-Si alloys using Nb-based heterogeneous nuclei. Nat Publ Gr2016; 6: 1–10.
46.
HackenhaarWMazzaferroJAEMazzaferroCCP, et al.Effects of different WAAM current deposition modes on the mechanical properties of AISI H13 tool steel. Weld World2022; 66: 2259–2269.
47.
LeVTSiD. Microstructural and mechanical characteristics of 308L stainless steel manufactured by gas metal arc welding-based additive manufacturing. Mater Lett2020; 271: 127791.
48.
ChiaHYWangLYanW. Influence of oxygen content on melt pool dynamics in metal additive manufacturing: high-fidelity modeling with experimental validation. Acta Mater2023; 249: 118824.
49.
ZhuCCheonJTangX, et al.Molten pool behaviors and their influences on welding defects in narrow gap GMAW of 5083 Al-alloy. Int J Heat Mass Transf2018; 126: 1206–1221.
50.
Ol'ShanskiiANMorozovBP. Evaluation of the effect of increased pressure of shielding gas on the decrease in porosity of welded joints in aluminium alloys. Weld Int2004; 18: 304–306.
51.
BelottiLPVan NulandTFWGeersMGD, et al.On the anisotropy of thick-walled wire arc additively manufactured stainless steel parts. Mater Sci Eng A2023; 863: 144538.
52.
KumaranMSenthilkumarV. Experimental characterization of stainless steel 316L alloy fabricated with combined powder bed fusion and directed energy deposition. Weld World2021; 65: 1373–1388.
53.
MailléLSantCLe Paven-ThivetC, et al.Structure and morphological study of nanometer W and W3O thin films. Thin Solid Films2003; 428: 237–241.
54.
PardalJMTavaresSSMFonsecaC, et al.Study of the austenite quantification by X-ray diffraction in the 18Ni-Co-Mo-Ti maraging 300 steel. J Mater Sci2006; 41: 2301–2307.
55.
KarimiPSadeghiEÅlgårdhJ, et al.Columnar-to-equiaxed grain transition in powder bed fusion via mimicking casting solidification and promoting in situ recrystallization. Addit Manuf2021; 46: 102086.
56.
WuWXueJWangL, et al.Forming process, microstructure, and mechanical properties of thin-walled 316L stainless steel using speed-cold-welding additive manufacturing. Metals (Basel)2019; 9: 09.
57.
KurzWBezencCGaM. Advanced Columnar to equiaxed transition in solidification processing. Sci Technol Adv Mater2001; 2: 185–191.
58.
BhattacharyaSDindaGPDasguptaAK, et al.Microstructural evolution of AISI 4340 steel during direct metal deposition process. Mater Sci Eng A2011; 528: 2309–2318.
59.
DakGGugulothKSirohiS, et al.Creep and high-temperature tensile deformation behavior of the TIG welded P92 / 304L dissimilar steel weld joints. J Mater Eng Perf2024; 1: 1–26.
WangLXueJWangQ. Correlation between arc mode, microstructure, and mechanical properties during wire arc additive manufacturing of 316L stainless steel. Mater Sci Eng A2019; 751: 183–190.
SamaeeVSandfeldSIdrissiH, et al.Dislocation structures and the role of grain boundaries in cyclically deformed Ni micropillars. Mater Sci Eng A2020; 769: 138295.
64.
LiMLuTDaiJ, et al.Microstructure and mechanical properties of 308L stainless steel fabricated by laminar plasma additive manufacturing. Mater Sci Eng A2020; 770: 7.
65.
LiJFAgyakwaPAJohnsonCM, et al.Interfacial reaction in Cu/Sn/Cu system during the transient liquid phase soldering process. Acta Mater2011; 59: 1198–1211.
66.
ProtopappasESmalCALangeFGD. Mechanical properties of a 316L forging material modified for resistance 10 sensitization. Proc 1st Int Cr Steel Alloy Congr1992; 2: 97–103.
67.
Table: Mechanical Properties of Wrought Stainless Steel (All Properties Minimum Specified, Usually Flat Products). 580.
68.
Yu ZhangXQin ZhaXQing GaoL, et al.Influence of shielding gas on microstructure and properties of GMAW SS2205 welded joints. Materials (Basel)2021; 14: 2671.
69.
FigueiredoRBKawasakiMLangdonTG, et al.The role of grain size in achieving excellent properties in structural materials. J Mater Res Technol2024; 30: 3448–3462.
70.
NikamPPArunDRamkumarKD, et al.Microstructure characterization and tensile properties of CMT-based wire plus arc additive manufactured ER2594. Mater Charact2020; 169: 110671.
71.
ShahSGopalAThronsenE, et al.Precipitation, mechanical properties and early slant ductile fracture in cyclic and naturally aged Al-Zn-Mg(-Cu) alloys. Mater Des2022; 222: 111026.
72.
DuraisamyRMohan KumarSRajesh KannanA, et al.Reliability and sustainability of wire arc additive manufactured plates using ER 347 wire-mechanical and metallurgical perspectives. Proc Inst Mech Eng Part C J Mech Eng Sci2021; 235: 1860–1871.
73.
RafieazadMGhaffariMVahedi NemaniA, et al.Microstructural evolution and mechanical properties of a low-carbon low-alloy steel produced by wire arc additive manufacturing. Int J Adv Manuf Technol2019; 105: 2121–2134.
74.
MurrLE. Handbook of materials structures, properties, processing and performance. Cham: Springer International Publishing Switzerland, 2015.
75.
LiHFuM. Damage evolution and ductile fracture. In: Deformation based processing of materials behavior, performance, modelling and control. USA: Elsevier, 2019, pp. 85–136. doi: https://doi.org/10.1016/b978-0-12-814381-0.00003-0
76.
KimSLeeSImY, et al.Effects of alloying elements on fracture toughness in the transition temperature region of base metals and simulated heat-affected zones of Mn-Mo-Ni low-alloy steels. Metall Mater Trans A2004; 35: 2027–2037.
Supplementary Material
Please find the following supplemental material available below.
For Open Access articles published under a Creative Commons License, all supplemental material carries the same license as the article it is associated with.
For non-Open Access articles published, all supplemental material carries a non-exclusive license, and permission requests for re-use of supplemental material or any part of supplemental material shall be sent directly to the copyright owner as specified in the copyright notice associated with the article.
