Sage Journals: Discover world-class research

Abstract

The current experimental work discusses the electric discharge machining (EDM) of super duplex stainless steel with conventional die-sinking and minimum quantity lubrication (MQL) approach. The dielectric used in the conventional die-sinking EDM process is kerosene, and sunflower oil with air mixture is used in MQL-type machining conditions. The solid-type alpha brass electrodes of diameter 10 mm were used for machining. The most prominent input variables like pulse time (OFF and ON) and discharge current (varied at 3 levels) were selected, and Taguchi's L9 orthogonal array design was selected for experimentation. The responses like electrode wear rate (EWR), hole circularity (HC), material removal rate (MRR), and surface roughness (SR) were analyzed. The output results obtained from the experimental trials were analyzed using S/N ratios and analysis of variance (ANOVA). The most contributing input parameter affecting the responses like SR, HC, MRR, and EWR outputs were analyzed. The results showed that the optimum machining conditions were obtained at L3 and L9 levels for conventional die-sinking and MQL-type machining conditions, respectively. Out of three varying input parameters, pulse time (OFF) is the most contributing factor in deciding various responses. The same has been confirmed by ANOVA analysis. The theoretical prediction of experimental data was made using the Fuzzy logic approach, and the best optimal level is found out individually for all four responses.

Keywords

Machining Taguchi fuzzy logic ANOVA roughness circularity

Get full access to this article

View all access options for this article.

References

Vignesh

Ramanujam

. Machining investigation on Ti-6Al-4V alloy using a wire electrical discharge hybrid turning (WEDHT) process. Mater Res Express 2019; 6: 86563.

Vignesh

Ramanujam

. Machining of Ti–6Al–4V using diffusion annealed zinc-coated brass wire in WEDHT. J Brazilian Soc Mech Sci Eng 2019; 41: 01-10.

Vignesh

Ramanujam

Kuppan

. A comprehensive review on wire electrical discharge based hybrid turning (WEDHT). Mater Today Proc 2018; 5: 12273–12284.

Vignesh

Ramanujam

. Response optimisation in wire electrical discharge machining of AISI H11 tool steel using Taguchi - GRA approach. Int J Mach Mach Mater 2018; 20: 474–495.

Huang

Zhang

Ming

, et al. A novel numerical predicting method of electric discharge machining process based on specific discharge energy. Int J Adv Manuf Technol 2017; 88: 409–424.

Vignesh

Ramanujam

. Numerical modelling and experimental validation of crater formation in WEDM hybrid turning of Ti-6Al-4V alloy. Proc Inst Mech Eng Part E J Process Mech Eng 2021; 235: 392–404.

Muthuramalingam

Mohan

. A review on influence of electrical process parameters in EDM process. Arch Civ Mech Eng 2015; 15: 87–94.

Puertas

Luis

. A study on the machining parameters optimisation of electrical discharge machining. J Mater Process Technol 2003; 143–144: 521–526.

Chattopadhyay

Verma

Satsangi

, et al. Development of empirical model for different process parameters during rotary electrical discharge machining of copper-steel (EN-8) system. J Mater Process Technol 2009; 209: 1454–1465.

10.

Kunieda

Yoshida

. Electrical discharge machining in gas. CIRP Ann Manuf Technol 1997; 46: 143–146.

11.

Hasçalik

Çaydaş

. Electrical discharge machining of titanium alloy (Ti-6Al-4V). Appl Surf Sci 2007; 253: 9007–9016.

12.

Hsieh

Lin

Chen

, et al. Surface modification and machining of TiNi/TiNb-based alloys by electrical discharge machining. Int J Adv Manuf Technol 2016; 86: 1475–1485.

13.

Dwivedi

Choudhury

. Improvement in the surface integrity of AISI D3 tool steel using rotary tool electric discharge machining process. Procedia Technol 2016; 23: 280–287.

14.

Shen

Liu

Sun

, et al. High-speed near dry electrical discharge machining. J Mater Process Technol 2016; 233: 9–18.

15.

Buschaiah

Jagadeeswararao

Krishnaiah

. Investigation on the influence of EDM parameters on machining characteristics for Aisi 304. Mater Today Proc 2018; 5: 3648–3656.

16.

Mohd Abbas

Solomon

Fuad Bahari

. A review on current research trends in electrical discharge machining (EDM). Int J Mach Tools Manuf 2007; 47: 1214–1228.

17.

Newman

. State of the art electrical discharge machining (EDM). Int J Mach Tools Manuf 2003; 43: 1287–1300.

18.

Jeykrishnan

Vijaya Ramnath

Chenbhaga Ram

, et al. Investigation on the influence of performance characteristics on machining Inconel 625 alloy in electro-discharge machining (EDM). Mater Today Proc 2018; 5: 20449–20454.

19.

Alshemary

Pramanik

Basak

, et al. Accuracy of duplex stainless steel feature generated by electrical discharge machining (EDM). Meas J Int Meas Confed 2018; 130: 137–144.

20.

Hamid

FEA

Lajis

. High performance in EDM machining of AISI D2 hardened steel. Adv Mater Res 2012; 500: 259–265.

21.

Kansal

Singh

Kumar

. Parametric optimization of powder mixed electrical discharge machining by response surface methodology. J Mater Process Technol 2005; 169: 427–436.

22.

Tsai

Wang

. Predictions on surface finish in electrical discharge machining based upon neural network models. Int J Mach Tools Manuf 2001; 41: 1385–1403.

23.

Leão

Pashby

. A review on the use of environmentally-friendly dielectric fluids in electrical discharge machining. J Mater Process Technol 2004; 149: 341–346.

24.

Yang

S-H

Srinivas

Mohan

, et al. Optimization of electric discharge machining using simulated annealing. J Mater Process Technol 2009; 209: 4471–4475.

25.

Tzeng

Chen

. Multi-objective optimisation of high-speed electrical discharge machining process using a Taguchi fuzzy-based approach. Mater Des 2007; 28: 1159–1168.

26.

Lin

Wang

Yan

, et al. Optimization of the electrical discharge machining process based on the Taguchi method with fuzzy logics. J Mater Process Technol 2000; 102: 48–55.

27.

Lin

. Optimisation of the EDM process based on the orthogonal array with fuzzy logic and grey relational analysis method. Int J Adv Manuf Technol 2002; 19: 271–277.

28.

Lin

Chung

Huang

. Improvement of machining accuracy by fuzzy logic at corner parts for wire-EDM. Fuzzy Sets Syst 2001; 122: 499–511.

29.

Yilmaz

Eyercioglu

Gindy

NNZ

. A user-friendly fuzzy-based system for the selection of electro discharge machining process parameters. J Mater Process Technol 2006; 172: 363–371.

30.

Viswanthvaleti

Radhakrishnan

. Green electrical discharge machining on Aisi 2507 super duplex stainless steel using grey. 2018; 8: 901–910.

Supplementary Material

Please find the following supplemental material available below.

For Open Access articles published under a Creative Commons License, all supplemental material carries the same license as the article it is associated with.

For non-Open Access articles published, all supplemental material carries a non-exclusive license, and permission requests for re-use of supplemental material or any part of supplemental material shall be sent directly to the copyright owner as specified in the copyright notice associated with the article.

0.00 MB

3.81 MB

0.04 MB

Experimental investigation to optimize machining parameters for super duplex stainless steel in spark EDM using die-sinking and MQL system

Abstract

Keywords

Get full access to this article

References

Supplementary Material