RETRACTED: Experimental investigation on the effect of laser powder bed fusion process variables on dimensional accuracy,surface roughness and cylindricity of the AlSi10Mg alloy component
Restricted accessRetractionFirst published online October, 2023
RETRACTED: Experimental investigation on the effect of laser powder bed fusion process variables on dimensional accuracy,surface roughness and cylindricity of the AlSi10Mg alloy component
WeiLShuaiLJieL,et al.Effect of heat treatment on AlSi10Mg alloy fabricated by selective laser melting: microstructure evolution, mechanical properties and fracture mechanism. Mater Sci Eng A2016; 663: 116–125.
2.
AmmarHSamuelASamuelF. Porosity and the fatigue behavior of hypoeutectic and hypereutectic aluminum–silicon casting alloys. Int J Fatigue2008; 30: 1024–1035.
3.
GuDShenY. Effects of processing parameters on consolidation and microstructure of W–Cu components by DMLS. J Alloys Compd2009; 473: 107–115.
4.
KarolewskaKLigajBWirwickiM,et al.Strength analysis of Ti6Al4 V titanium alloy produced by the use of additive manufacturing method under static load conditions. J Mater Res Technol2020; 9: 1365–1379.
5.
NayakPKSahuAKMahapatraSS. Effect of process parameters on the mechanical behavior of FDM and DMLS build parts. Mater Today Proc2020; 22: 1443–1451.
6.
FotovvatiBAlirezaEtesamiSAsadiE. Process-property-geometry correlations for additively-manufactur. Mater Sci Eng A2019; 760: 431–447.
7.
Anush RajBWinowlin JappesJTAdam KhanM,et al.Direct Metal Laser Sintered (DMLS) process to develop Inconel 718 alloy for turbine engine components. Optik2020; 202: 163735.
8.
AvanziniABattniDGelfiM,et al.Investigation of fatigue strength of sand - blasted DMLS AlSi10Mg alloy. Procedia Structural Integrity2019; 18: 119–128.
9.
TezelTTopalESKovanV. Characterizing the wear behaviour of DMLS-manufactured gears under certain operating conditions. Wear2019; 440–441: 203106.
10.
ZakrzewskiTKozakJWittM,et al.Dimensional analysis of the effect of SLM parameters on surface roughness and material density. Procedia CIRP2020; 95: 115–120.
11.
Fielden-StewartZCoopeTBachevaD,et al.Effect of the surface morphology of SLM printed aluminium on the interfacial fracture toughness of metal-composite hybrid joints”. Int J Adhes Adhes2021; 105: 102779.
12.
SenthilkumaranKPandeyPMRaoPVM. Statistical modeling and minimization of form error in SLS prototyping. Rapid Prototyp J2012; 18: 38–48.
13.
MohamedOAMasoodSHBhowmikJL. Experimental investigation for dynamic stiffness and dimensional accuracy of FDM manufactured part using IV-optimal response surface design. Rapid Prototyp J2017; 23: 736–749.
14.
RoyR. A primer on the Taguchi method. Society of Manufacturing Engineers, Dearborn, 1990.
15.
SinghJSinghRSinghH. Repeatability of linear and radial dimension of ABS replicas fabricated by fused deposition modelling and chemical vapor smoothing process: A case study. Measurement2016; 94: 5–11.
16.
MauryaNKRastogiVSinghP. Investigation of dimensional accuracy and international tolerance grades of 3D printed polycarbonate parts. Mater Today Proc2020; 25(Part 4): 537–543.
17.
MauryaNKRastogiVSinghP. Fabrication of prototype connecting rod of PLA plastic material using FDM prototype technology. Indian J Eng Mater Sci2020; 27: 333–343.
18.
Maurya1NKRastogiVSinghP. Comparative study and measurement of form errors for the component printed by FDM and PolyJet process. Instrumentation MesureMétrologie2019; 18: 353–359.
19.
ZhangZLiuM-YBretonF,et al.Microstructure and mechanical properties of AlSi10Mg permanent mould and high pressure vacuum die castings. In: Published in the Proceedings of the 16th International Aluminum Alloys Conference (ICAA16)2018. ISBN: 978-1-926872-41-4.
