Investigation of pulp flow helicity in rotating and non-rotating grooves

Abstract

Numerical simulation of pulp flow in rotating and non-rotating grooves is carried out to investigate the effect of pulp rheological properties and groove geometry on the rotational motion of the pulp flow. The eucalyptus pulp suspension is considered as a working fluid in the present study whose apparent viscosity correlation is available from the experimental measurements reported in the literature. The simulations are carried out with OpenFoam for different values of pulp material, fiber concentrations, and groove cross-section. Helicity is introduced to measure the turnover rate of pulp flow in the groove due to the importance of such motion on the final properties of the pulp flow. A measurement of helicity magnitude and its distribution along the groove revealed that a change in the pulp material would significantly affect the flow structures within the groove. Further investigation on the effects of fiber concentration, c, showed that this parameter does not have a significant effect on the averaged helicity magnitude for c = 2.0 and 2.5, whereas the helicity distribution over the groove cross-section changes clearly for c = 1.5. The results showed that the helicity level is negligible for almost half of the cavity cross-section in the non-rotating groove simulations, which can be considered as a shortcoming of the original geometry of the groove. Therefore, a smaller cross-section for the groove is considered through which an enhancement in the helicity magnitude is observed.

Keywords

Non-Newtonian flow eucalyptus pulp helicity rotating groove

Get full access to this article

View all access options for this article.

References

Cotas

Garcia

Rasteiro

, et al. Modelling of concentrated fibre suspension pipe flow with low-Reynolds-number k–ε turbulence models: new damping function. Nord Pulp Pap Res J 2017; 32: 132–147.

Berg

J-E

Sandberg

Engberg

, et al. Low-consistency refining of mechanical pulp in the light of forces on fibres. Nord Pulp Pap Res J 2015; 30: 225–229.

Heymer

Olson

Kerekes

. The role of multiple loading cycles on pulp in refiners. Nord Pulp Pap Res J 2011; 26: 284.

Hietanen

Ebeling

. Fundamental aspects of the refining process. Pap Puu 1990; 72: 158–170.

Muhic

Huhtanen

J-P

Sundström

, et al. Energy efficiency in double disc refining. Influence of intensity by segment design. Nord Pulp Pap Res J 2011; 26: 224–231.

Sandberg

Berg

J-E

. Effect of flow recirculation on pulp quality and energy efficiency in low consistency refining of mechanical pulp. Nord Pulp Pap Res J 2015; 30: 230–233.

Fox

Brodkey

Nissan

. Inside a disc refiner. Tappi J 1982; 65: 80–83.

Lumiainen

. Plate pattern and fiber dimensions have an effect on the performance of the refiner. In: TAPPI engineering conference 1994, 265–265. TAPPI PRESS.

Mithrush

. An experimental study of fluid flow in a low consistency refiner. Master Thesis, University of British Columbia, Canada, 2013.

10.

Kohkar

. Numerical simulation of the flow in a disc refiner. 2011.

11.

Wittberg

Björkman

Khokhar

, et al. Flow conditions in the grooves of a low-consistency refiner. Nord Pulp Pap Res J 2012; 27: 173–183.

12.

Kondora

Asendrych

. Flow modelling in a low consistency disc refiner. Nord Pulp Pap Res J 2013; 28: 119–130.

13.

Ventura

Blanco

Negro

, et al. Modeling pulp fiber suspension rheology. Tappi J 2007; 6: 17–23.

14.

Nasab

Mithrush

Olson

, et al. Turbulent Couette flow between corrugated walls: the case with motion of one wall perpendicular to the corrugation cavities. Can J Chem Eng 2014; 92: 1766–1775.

15.

Levy

Degani

Seginer

. Graphical visualization of vortical flows by means of helicity. AIAA J 1990; 28: 1347–1352.

16.

Moffatt

. The degree of knottedness of tangled vortex lines. J Fluid Mech 1969; 35: 117–129.

17.

Moffatt

Tsinober

. Helicity in laminar and turbulent flow. Annu Rev Fluid Mech 1992; 24: 281–312.

18.

Povitsky

. Three-dimensional flow with elevated helicity in driven cavity by parallel walls moving in perpendicular directions. Phys Fluids 2017; 29: 083601.

19.

Tsynober

. The essence of turbulence as a physical phenomenonx. Springer, Netherlands, Dordrecht, 2014.

20.

Shankar

Deshpande

. Fluid mechanics in the driven cavity. Annu Rev Fluid Mech 2000; 32: 93–136.

21.

Ohta

Miyashita

. DNS And LES with an extended Smagorinsky model for wall turbulence in non-Newtonian viscous fluids. J Non-Newtonian Fluid Mech 2014; 206: 29–39.

22.

Hong

Shi

, et al. Simulation of power-law fluid flows in two-dimensional square cavity using multi-relaxation-time lattice Boltzmann method. Commun Comput Phys 2014; 15: 265–284.

23.

Abe

Kawamura

Matsuo

. Direct numerical simulation of a fully developed turbulent channel flow with respect to the Reynolds number dependence. J Fluids Eng 2001; 123: 382–393.

24.

Huhtanen

Karavian

. Characterization of non-Newtonian fluid models for wood fiber suspensions in laminar and turbulent flows. Ann Trans Nord Rheology Soc 2006; 14: 51–60.

25.

Duanmu

Gamstedt

Rosling

. Synthesis and preparation of crosslinked allylglycidyl ether-modified starch-wood fibre composites. Starch-Stärke 2007; 59: 523–532.

26.

Morais

Bértolo

Curto

, et al. Comparative characterization of eucalyptus fibers and softwood fibers for tissue papers applications. Mater Lett X 2019; 4: 100028.

27.

Jouybari

Engberg

Persson

. Large eddy simulation of turbulent pulp flow in a channel. J Non-Newtonian Fluid Mech 2020; 285: 104409.