The effect of an auxiliary spring on the decrease of contact resistance and contact temperature for power automotive connector

Abstract

Power automotive connectors used to connect two electrical systems in an electric vehicle should resist the rising of electric power or electric current. The latter can cause a rise in contact temperature by the Joule effect and can damage a connector improperly designed. The purpose of this work is to study experimentally and numerically the influence of the addition of a second spring on the ability of a power connector to transmit a high current. For this reason, an experimental test has been held on a connector without a second spring to measure contact resistance and contact temperature; then, a finite element model FEM of this connector was developed to compare and validate the numerical results with the experimental results. In addition, another FE model with a second spring was used to minimize contact resistance and contact temperature. Moreover, a theoretical model has shown its effectiveness in contact temperature and contact area calculations; it provides good agreement with experimental and numerical results. Numerical results show that the effect of the addition of a 2nd spring on the decrease of the contact temperature and contact resistance is significant. In addition, the thermo-electrical analysis by finite element shows that the current limit supported by a power connector with an auxiliary spring will equal twice the current supported by a power connector with one spring. FE mechanical analysis shows that the maximum mechanical stress in the connector with an auxiliary spring remains lower than the 2nd spring material yield stress. Finally, experimental and numerical results are in good agreement.

Keywords

Contact resistance contact temperature contact heating law high copper alloys second spring experimental test finite element mechanical stress power automotive connector

Get full access to this article

View all access options for this article.

References

Slade

PG.

Electrical contacts: principles and applications. 2nd ed. New York, NY: CRC Press, 2014.

Holm

Electric contacts: theory and applications. 4th ed. Berlin: Springer-Verlag, 1981.

Persson

BNJ

. On the electric contact resistance. Trib Lett 2022; 70: 1–9.

Shinomura

Sekikawa

. Dependence of contact resistance and surface deformation on surface roughness in silver contacts. In: Proceedings of the 31st international conference on electric contacts, Sapporo, Japan, 2022. ICEC.

Saha

Wynne

Jackson

RL.

Electro-thermo-mechanical contact analysis considering temperature dependent material properties and electrical contact resistance determination. In: Proceedings of the 66th Part2 Holm conference on electrical contacts, San Antonio, TX, USA, 24–27 October 2021, pp. 8–15. New York: IEEE.

Greenwood

JA.

Constriction resistance and the real area of contact. Br J Appl Phys 1966; 17: 1621–1632.

Timsit

. On the melting of ohmic-heated nanowires and electrical contacts. In: Proceedings of the 64th Holm conference on electrical contacts, Albuquerque, NM, USA, 14–18 October 2018, pp. 373–380. New York: IEEE.

Malucci

. The effects of bridge structures on current density and temperature distributions. In: Proceedings of the 64th Holm conference on electrical contacts, Albuquerque, NM, USA, 14–18 October 2018, pp. 43–47. New York: IEEE.

Gatzsche

Zanetti

Blumenroth

. Qualification of power contacts in high-voltage products for IEC 115°C limit temperature. In: Proceedings of the 30th international conference on electric contacts, On-line COVID19, 2020. ICEC.

10.

El Abdi

Beloufa

Benjemaa

. Contact resistance study of high copper alloys used in power automotive connectors. Proc IMechE, Part D: J Automobile Engineering 2008; 222: 1375–1383.

11.

Beloufa

Benjemaa

El Abdi

, et al. Numerical and experimental study of the contact resistance for high copper alloys used in force domain 1–100 N. In: Proceedings of the 24th international conference on electric contacts, Saint Malo, France, 2008, pp. 199–205. France: ICEC.

12.

Hadda

Beloufa

Amirat

, et al. Investigation on contact surfaces damage of copper contacts by an electric arc. Arch Mech Eng 2024; 71: 1–22.

13.

Saitoh

Iida

Sawada

, et al. Dependency of contact resistance on load. In: Proceedings of the 53rd Holm conference on electrical contacts, Pittsburgh, PA, USA, 2007, pp. 70–75. New York: IEEE.

14.

Beloufa

Mastorakis

Martin

. Influence of shapes, contact forces and high copper alloys on the contact resistance and temperature. In: Proceedings of the 2nd international conference on engineering mechanics, structures, engineering geology, Rodos, 22–25 July 2009, pp. 139–144. WSEAS.

15.

Duan

Zhu

, et al. Contact resistance investigation of electrical connector with different shrink range. In: Proceedings of the IEEE 15th international conference on electronic packaging technology, Chengdu, China, 12–15 August 2014, pp. 1146–1149. ICEPT.

16.

Monnier

Froidurot

Jarrige

, et al. A coupled-field simulation of an electrical contact during resistance welding. In: Proceedings of the 52nd Holm conference on electrical contacts, Montreal, QC, Canada, 25–27 September 2006, pp. 95–102. New York: IEEE.

17.

Beloufa

Design optimization of electrical power contact using finite element method. J Heat Transfer 2012; 134: 1–15.

18.

Schlegel

Grossmann

Lakner

, et al. Investigations on material structural changes on electrical joints at high contact temperature. In: Proceedings of the 26th international conference on electric contacts jointly held with the 4th international conference on reliability of electric production & elecric contacts, Beijing, China, 14–17 May 2012, pp. 7–11. ICEC-ICREPEC.

19.

Wilson

McIntosh

Timsit

. Contact spot temperature and the temperature of external surfaces in an electrical connection. In: Proceedings of the 26th international conference on electric contacts jointly held with the 4th international conference on reliability of electric production & elecric contacts, Beijing, China, 14–17 May 2012, pp. 12–17. ICEC-ICREPEC.

20.

Schreiber

Behrens

Honig

, et al. Contact resistance and overtemperature behavior of new and pre-Arced power engineering contacts as a function of ambient temperature and contact force. In: Proceedings of the 27th international conference on electric contacts, Dresden, Germany, 22–26 June 2014, pp. 344–350. VDE.

21.

Gatzsche

Lücke

Großmann

, et al. Electric-thermal performance of contact elements in high power plug-in connections. In: Proceedings of the 60th Holm conference on electrical contacts, New Orleans, LA, USA, USA, 12–15 October 2014, pp. 51–58. New York: IEEE.

22.

Wang

, et al. Simulation and experimental study on temperature rise characteristic of a piercing connector. IEEE Trans Compon Packag Manuf Technol 2022; 12: 512–521.

23.

Angadi

Jackson

Pujar

, et al. A comprehensive review of the finite element modelling of electrical connectors including their contacts. IEEE Trans Comp Pack Manuf Tech 2020; 10: 836–844.

24.

Lee

Yoo

, et al. Analysis of small-sized power connectors for mobile device batteries. J Inst Korean Electr Electron Eng 2015; 19: 101–109.

25.

Beloufa

The effect of cable section on the variation of power automotive connector temperature. IEEE Trans Comp Pack Manuf Tech 2019; 9: 1020–1028.

26.

Fjeld

Rondeel

Sønsteby

, et al. Contact resistance and temperature rise of cable connections in cable distribution cabinets. In: Proceedings of the 66th Part1 Holm conference on electrical contacts (On line-Covid19), 2020, pp. 110–114. New York: IEEE.

27.

LuxShare Tech Company, manufacturer of the power busbar connectors, China, https://www.luxshare-tech.com/2123PowerBusbar_en.aspx(2024).

28.

Zauter

Kudashov

. Precipitation hardened high copper alloys for connector pins made of wire. In: Proceedings of the 23rd international conference on electric contacts, Sendai, Japan, 6–9 June 2006, pp. 257–261. ICEC.

29.

Wieland-Werke AG Group, manufacturer of high copper alloys, Germany, https://www.wieland.com/en (2024).

30.

Swiss Steel Group, manufacturer of chromium-nickel austenitic stainless steel 1.4310, Germany, https://swisssteel-group.com/en (2024).

31.

Haynes

. Handbook of chemistry and physics. 95th ed. New York, NY: CRC Press, 2014–2015.

32.

Ansys. Release. Canonsburg Southpointe, PA: Ansys Inc., 2020.

33.

Cao

Heat transfer in process engineering. New York, NY: McGraw-Hill, 2010.

34.

Beloufa

Amirat

Design and study of new power connector with parallel contact points. Proc IMechE, Part D: J Automobile Engineering 2018; 232: 2014–2021.

35.

El Abdi

Benjemaa

Beloufa

. Numerical and experimental studies of automotive connector behavior. In: Proceedings of the18th International conference on modeling and simulation, Montreal, Canada, 2007, pp. 209–214. IASTED.

36.

El Abdi

Benjemaa

Beloufa

. Behaviour evolution of automotive connectors. Proc IMechE, Part D: J Automobile Engineering 2008; 222: 151–159.

37.

Beloufa

A comprehensive study on optimizing mechanical stress, contact temperature, and electrical contact resistance. In: Qassim

(ed.) Theory and applications of engineering research, vol. 9. India and UK: Book Publishers International (BPI), 2024, pp. 114–139.

38.

Hertz

Über die berührung fester elastischer körper. J. für die reine und angewandte mathematik 1882; 92: 156–171.

39.

Sridhar

Yovanovich

MM.

Elastoplastic constriction resistance of sphere/flat contacts: theory and experiment. J Heat Transfer 1996; 118: 202–205.

Supplementary Material

Please find the following supplemental material available below.

For Open Access articles published under a Creative Commons License, all supplemental material carries the same license as the article it is associated with.

For non-Open Access articles published, all supplemental material carries a non-exclusive license, and permission requests for re-use of supplemental material or any part of supplemental material shall be sent directly to the copyright owner as specified in the copyright notice associated with the article.

0.00 MB