The composite material properties were largely dependent on the processing methods and the parameters employed during their manufacturing. In this study, Al-Si/Coconut Shell Ash (CSA) metal matrix composites were produced using the stir cast method. The potentiodynamic polarization method was utilized to assess the electrochemical behavior of the composites in a 3.5% NaCl solution. The corrosion current density (Icorr) and corrosion potential (Ecorr) were measured, indicating a trend of heightened corrosion susceptibility with increased CSA concentration. The rise in corrosion rate is ascribed to microstructural alterations and galvanic interactions between the matrix and CSA particles. Tribological tests were conducted on a pin-on-disc tester with a load ranging from 30 and 50 N, and moving speed up to 3 m/s utilizing two distinct lubricants, SAE20W-40 and Rice brain Oil. This research looks at the effects of three distinct CSA weight percentages that is, 5%, 10%, and 15%. As the weight % of CSA increased, composite density fell and mechanical characteristics improved. It has been observed that the 10% CSA composite surface has a small amount of plowing and cracks from light abrasion wear, and the asperities have a small amount of plastic deformation. SEM pictures are acquired to reinforce the wear and friction characteristics that are identified through a comparison of dry and lubricated situations. When compared to dry circumstances, lubricated ones result in a significant reduction in the amount of wear and friction.
GnanavelbabuAVinothkumarERossNS, et al. Tribo-corrosive wear and mechanical properties of nanoparticles reinforced Mg-AZ91D composites. Tribol Int2023; 178: 108054.
2.
MallieswaranKRajendranCAravindhanN, et al. Correction to: Effect of heat treatment on the structure and properties of laser welded joints of aluminum alloy AA2024. Met Sci Heat Treat2023; 64: 609.
3.
RajeshAKarthickSMallieswaranK, et al. Tensile strength analysis of electron beam welded AA2024 aluminum alloy joints. SAE technical paper, 2024, pp.1–6. 10.4271/2024-01-5220.
4.
VuddagiriHKVadapalliSSagariJ, et al. Fabrication and modelling of tribological performance of Al-Si/12Al2O3/2MoS2 composite using Taguchi technique. Int J Autom Mech Eng2021; 18: 8959–8977.
5.
ThimothyPSankara RajuSRatnamC.Development and accretion of tribological performance on Al-CSA composites using orthogonal array. Mater Today Proc2019; 18: 5332–5339.
6.
RaoRNDasSMondalDP, et al. Dry sliding wear maps for AA7010 (Al–Zn–Mg–Cu) aluminium matrix composite. Tribiol Int2013; 60: 77–82.
7.
VuddagiriHKRallabandiSRVadapalliS, et al. Assessment of mechanical and tribological performance of hybrid Al/MoS2/Al2O3 composite by GFRA. Metall Mater Eng2022; 28: 79–102.
8.
RaoCJSiva Sankara RajuR, et al. Fabrication and evaluation of optimized parametric condition during EDM machining of Al-CSA composite using Taguchi orthogonal array. In: LionelGKarthikeyanRMuralidharanV, et al. (eds) Advances in design and thermal systems: select proceedings of ETDMMT 2020. Singapore: Springer, 2021, pp.411–420.
9.
BabuRRajendranCSaiyathibrahimA, et al. Influence of B4C and ZrB2 reinforcements on microstructural, mechanical and wear behaviour of AA 2014 aluminium matrix hybrid composites. Def Technol2024; 40: 242–254.
10.
JayarajAMoorthyCVKNSNVenkataramanaVSN, et al. Corrosion, mechanical and thermal properties of aluminium alloy metal matrix nano composites (AA-MMNCs) with multi-walled carbon nanotubes. SN Appl Sci2020; 2: 1259–1267.
11.
ZhaoJZhaoTZhangY, et al. Corrosion behavior of the 2024 aluminum alloy in the atmospheric environment of the South China Sea Islands. Coatings2024; 14: 331–342.
12.
AlbahlolOAACugHAkgulY, et al. Effect of laser hardening on the mechanical, tribological and corrosion properties of low alloy steels. J Min Metall Sect B Metall2023; 59: 255–267.
13.
LiZ.Microstructure evolution and corrosion behavior of Al-Si/Al-Mn composites in salt spray. Mater Tehnol2022; 56: 139–147.
14.
Suresh KumarRSenthil KumarSRajendranC, et al. Investigation on corrosion behaviour of LM25-SiCp composite using Taguchi method. Adv Mater Sci Eng2022; 2022: 1–9.
15.
GudlurPMulianaARadovicM.Effective thermo-mechanical properties of aluminum–alumina composites using numerical approach. Compos B Eng2014; 58: 534–543.
16.
Siva Sankara RajuRVenkata SivaBSrinivasa RaoG. Quantitative analysis of tribological performance on Al–CSA composite using orthogonal array. In: VorugantiHKKumarKKrishnaP, et al. (eds) Advances in applied mechanical engineering (lecture notes in mechanical engineering (LNME)). Singapore: Springer Nature Singapore Pte Ltd, 2020, pp.381–388.
17.
MoheimaniSKKeshtgarAKhademzadehS, et al. Tribological behaviour of AZ31 magnesium alloy reinforced by bimodal size B4C after precipitation hardening. J Magnes Alloys2022; 10: 3267–3280.
18.
BaradeswaranAElaya PerumalA.Study on mechanical and wear properties of Al 7075/Al2O3/graphite hybrid composites. Compos Part B2014; 56: 464–471.
19.
ChenCBosseHDetersL.Effects of various base oils and additives on the tribological behaviour of lubricated aluminium- on-aluminium and steel-on-aluminium contacts. Proc IMechE, Part J: J Engineering Tribology2009; 223: 571–580.
20.
VenkatesanPSAhmedNGoldmanIB.Frictional studies of tool steel against aluminum under high pressure using liquid lubricants. Wear1971; 17: 245–258.
21.
GradtTSchneiderT.Tribological performance of MoS2 coatings in various environments. Lubricants2016; 4: 32–45.
22.
PoriaSSutradharGSahooP.Wear and friction behavior of stir cast Al-TiB2 metal matrix composites with various lubricants. Tribol Ind2016; 38: 508–521.
23.
BiswasMASRahmanMMOrtegaJA, et al. Lubrication performance of sunflower oil reinforced with halloysite clay nanotubes (HNT) as lubricant additives. Lubricants2022; 10: 139.
24.
FoxNJTyrerBStachowiakGW. Boundary lubrication performance of free fatty acids in sunflower oil. Tribol Lett2004; 16: 275–281.
SinhaSAgarwalAKGargS.Biodiesel development from rice bran oil: transesterification process optimization and fuel characterization. Energy Convers Manag2008; 49: 1248–1257.
27.
RajuSSPanigrahiMKGangulyRI, et al. Investigation of tribological behavior of a novel hybrid composite prepared with Al-coconut shell ash mixed with graphite. Metallurgical Mater Trans A2017; 48: 3892–3903.
28.
Sankara RajuRSPanigrahiMKGangulyRI, et al. Tribological behaviour of al-1100-coconut shell ash (CSA) composite at elevated temperature. Tribol Int2019; 129: 55–66.
29.
DasSBiswasSK.Boundary lubricated tribology of an aluminium–silicon alloy sliding against steel. Tribol Lett2004; 17: 623–628.
30.
MallieswaranKAgaramudhalvanSGeorge OliverD.Microstructural stability and strength correlation in AGG-affected friction stir welded AA2024-T4 joints. Adv Mater Process Technol2025; 1–10. DOI: 10.1080/2374068x.2025.2501044
31.
RajuSSSrinivasa RaoGSamantraC.Wear behavioral assessment of Al-CSAp-MMCs using grey-fuzzy approach. Measurement2019; 140: 254–268.
32.
RaoRNDasS.Effect of SiC content and sliding speed on the wear behaviour of aluminium matrix composites. Mater Des2011; 32: 1066–1071.
33.
RajuRSSSivaBV. Fabrication and tribological studies of Al-CSA composite using RSM. Int J Mater Eng Innov2021; 12: 83–102.
34.
RadhikaN.Fabrication of LM25/SiO2 metal matrix composite and optimization of wear process parameters using design of experiment. Tribol Ind2017; 39(1): 1–8.
35.
MuraliTPSurappaMKRohatgiPK.Preparation and properties of Al-alloy coconut shell char particulate composites. Metallurgical Trans B1982; 13: 485–494.
36.
RallabandiSRSrinivasLPalliS, et al. A contrastive characterization of pure Mg and AZ91D alloy based on the testing of mechanical, corrosion, wear, and erosion properties. Eng Res Express2024; 6: 015017.
37.
Venkata SivaSBSahooKLGangulyRI, et al. Preparation of aluminum metal matrix composite with novel in situ ceramic composite particulates, developed from waste colliery shale material. Metallurgical Mater Trans B2013; 44: 800–808.
38.
GovindaraoRGangulyRIDashRR, et al. Development of a novel aluminium based metal matrix composite using insitu ternary mixture (Al2O3-sic-C) prepared by thermal treatment of fly-ash. Trans Indian Ins Metals2015; 68: 951–958.
39.
AlpasATZhangJ. Effect of microstructure (particulate size and volume fraction) and counterface material on the sliding wear resistance of particulate-reinforced aluminum matrix composites. Metallurgical Mater Trans A1994; 25: 969–983.
40.
RallabandiSRRajuSSrinivasa RaoG.Assessment of tribological performance of Al-coconut shell ash particulate—MMCs using grey-fuzzy approach. J Inst Eng Ser C2019; 100: 13–22.
41.
AtuanyaCUIbhadodeAOADagwaIM.Effects of breadfruit seed hull ash on the microstructures and properties of Al–Si–Fe alloy/breadfruit seed hull ash particulate composites. Results Phys2012; 2: 142–149.
42.
ArchardJF.Contact and rubbing of flat surfaces. J Appl Phys1953; 24: 981–988.
43.
KatoK.Wear in relation to friction — a review. Wear2000; 241: 151–157.
44.
JeyaprakashNYangCH.Friction, lubrication, and wear. In: PatnaikASinghTKukshalV (eds) Tribology in materials and manufacturing. London: IntechOpen, 2021, pp.326–342.
45.
RajuSSMuraliGBPatnaikPK.Ranking of Al-CSA composite by MCDM approach using AHP–TOPSIS and MOORA methods. J Reinforced Plast Compos2020; 39: 721–732.
46.
RaoRNDasS.Effect of applied pressure on the tribological behaviour of SiCp reinforced AA2024 alloy. Tribiol Int2011; 44: 454–462.
47.
ZhaoZWongTTLeungCW.Impinging premixed butane/air circular laminar flame jet––influence of impingement plate on heat transfer characteristics. Int J Heat Mass Transf2004; 47: 5021–5031.
48.
ChenBMZhangJXLiangZF, et al. Effects of MoS2 on tribological properties and mechanically mixed layer of al matrix composites. Mater Sci Forum2017; 896: 83–96.
49.
MurakamiTKajinoSNakanoS.High-temperature friction and wear properties of various sliding materials against aluminum alloy 5052. Tribol Int2013; 60: 45–52.
50.
JhaNBadkulAMondalDP, et al. Sliding wear behaviour of aluminum syntactic foam: a comparison with Al–10wt% SiC composites. Tribol Int2011; 44: 220–231.
