Light-weight design of an overhead crane’s girder with a non-symmetric box cross-section

Abstract

The proper choice of material and geometric properties of the girder of the bridge crane can significantly reduce its weight and production cost. This research presents the weight optimization of the main girder with a non-symmetric box-like cross-section. The strength analysis in characteristic points of the critical cross-section and the local stability of plates were conducted using Eurocodes. This study aimed to prove that a proper choice of geometry for the cross-section plates and their additional design elements can have a meaningful impact on the weight. The optimization procedure was done using Water Evaporation Optimization (WEO) algorithm, with the implementation of all necessary criteria and conditions which must be fulfilled. This study revealed that the application of the light-weight design philosophy to the structure of the main girder could significantly reduce its weight, which is verified in the existing examples of double-beam bridge cranes. Achieved savings in girder weight are between 24.43% and 34.73%, dependingly on the considered example. Also, the study showed the influence of the chosen material on the steel girder’s optimum weight and geometric parameters. Depending on the studied example of the bridge crane and selected material, the WEO algorithm gave the same solution through simulations. The value of the optimum weight had a slight deviation at the second decimal place, which is neglectable. The algorithm successfully avoided the trap of getting into the local minimum during the search. In the end, it can be stated that the application of the WEO algorithm was successful in the considered engineering problem since it was the optimization of a complex steel structure with 11 variables and more than 20 constraint functions.

Keywords

Overhead crane optimum design steel girder Eurocodes metaheuristic

Get full access to this article

View all access options for this article.

References

Yixiao

Haiming

. High Precision Analysis of stress concentration in girder structure of casting crane. Int J Sci Qual Anal 2016; 2(2): 14–18.

Husen

. Girder deflection for lifting load. M Sc theses, Faculty of Engineering, University of Malaya, Kuala Lumpur, Malaysia, 2017.

Wen

. Static analysis of Bridge Crane carriage based on ANSYS. Int J Soc Sci Educ Res 2018; 1(1): 90–93.

Chang

Sharma

. Analysis and design of general bridge crane structure using CAD technology. Comput Aided Des Appl 2022; 19(S2): 15–25.

Molnár

Blatnický

Dižo

. Comparison of analytical and numerical approach in bridge crane solution. Manuf Technol 2022; 22(2): 192–199.

Meng

Yifei

Xiangdong

. Finite element analysis of bridge crane metal structure based on ABAQUS. MATEC Web Conf 2018; 198: 01004.

Mohamed

Abdelwahab

. Double-girder overhead crane optimum design using weighted decision matrix and Finite Element Analysis. J Inst Eng (India) Ser C 2021; 102(2): 283–304.

Yang

Cheng

Xiao

, et al. Engineering design optimisation using reinforcement learning with episodic controllers. Cognit Comput Syst 2022; 4: 340–350.

Ahmid

Dao

. An adaptive discrete cuckoo search algorithm to solve structural optimization problems. JMEST 2020; 7(5): 283–304.

10.

Yeşilbel

Çimen

Kalyoncu

. Optimum design of overhead crane construction using the bees algorithm. TIJMET 2021; 0004: 157–167.

11.

, et al. Comprehensive research on energy-saving green design scheme of crane structure based on computational intelligence. AIP Adv 2021; 11: 075314.

12.

Wang

, et al. Characteristics analysis and optimization design of bridge crane based on improved particle swarm optimization algorithm. J Low Freq Noise Vib Active Control 2023; 42(1): 253–271.

13.

Qin

Yang

. Structural optimization of unsymmetrical eccentric load steel box girder based on new swarm intelligence optimization algorithm. Int J Steel Struct 2022; 22: 1518–1536.

14.

Pavlović

Savković

. Analysis and optimization of the main girder of the bridge crane with an asymmetric box cross-section. Sci Tech Rev 2022; 72(1): 3–11.

15.

Pavlović

Savković

Zdravković

, et al. Low-weight design of a monosymmetric box girder of a double girder bridge crane with two trolleys. In: XXIV international conference on “material handling, construction and logistics” MHCL’22, Faculty of Mechanical Engineering, University of Belgrade, Belgrade, Serbia, 21–23 September 2022, pp.137–142.

16.

Savković

Bulatović

Gašić

, et al. Optimization of the box section of the main girder of the single-girder bridge crane by applying biologically inspired algorithms. Eng Struct 2017; 148: 452–465.

17.

Pavlović

Jerman

Savković

, et al. Metaheuristic applications in mechanical and Structural Design. Engineering Today 2022; 1(1): 19–26.

18.

http://www.menagroup.bg/en/content/double-girder-bridge-crane

19.

Ostrić

Tošić

. Cranes. Institute for Mechanization of the Faculty of Mechanical Engineering of the University in Belgrade, Serbia, 2005.

20.

prEN 13001–3–1. Eurocode 3: Cranes – General design – Limit states and proof of competence of steel structures. Brussels: European Committee for Standardization, 2010.

21.

Jármai

Farkas

. Optimum cost design of welded box beams with longitudinal stiffeners using advanced backtrack method. Struct Multidiscipl Optim 2001; 21: 52–59.

22.

Kaveh

Bakhshpoori

. Water evaporation optimization: A novel physically inspired optimization algorithm. Comput Struct 2016; 167: 69–85.

23.

Kaveh

Bakhshpoori

. A new metaheuristic for continuous structural optimization: water evaporation optimization. Struct Multidiscipl Optim 2016; 54: 23–43.

24.

Wang

Y-J

Zhou

S-N

Che

X-Y

. Constrained multi-objective water evaporation optimization algorithm based on decomposition with ε-constraint handling technology. IEEE Access 2020; 8: 130986–131004.

25.

Kaveh

Bakhshpoori

. An accelerated water evaporation optimization formulation for discrete optimization of skeletal structures. Comput Struct 2016; 177: 218–228.

26.

Kaveh

. Metaheuristics-Outlines, MATLAB codes and example. Berlin: Springer Nature Switzerland AG, 2019.

27.

Pavlović

Savković

Zdravković

, et al. Design optimization of the rectangular box section of the double beam bridge crane using Matlab optimization toolbox. In: IX triennial international conference “heavy machinery-HM 2017”, Faculty of Mechanical and Civil Engineering in Kraljevo, University of Kragujevac, Kraljevo, Serbia, 28 June–1 July 2017, pp.37–44.