Optimization of process parameters in magnetic field assisted powder mixed EDM of aluminium 6061 alloy

Abstract

Magnetic field assisted powder mixed electrical discharge machining (MFAPM-EDM) is a variant of EDM process where magnetic field coupled with electric field is used with addition of fine powder in dielectric to improve the surface quality, machining rate and stability of the process. Aluminium 6061 alloy as workpiece was selected due to growing use in aviation, automotive, naval industries. In this present work, parametric study and optimization was carried out on MFAPM-EDM machined Aluminium 6061 alloy. In this study, process parameters such as discharge current (I_P), spark duration (P_ON), pause duration (P_OFF), concentration of powder (CP) and magnetic field (MF) were considered to analyze the effect on material erosion rate (MER) and electrode wear rate (EWR). Box Behnken design approach based on response surface methodology (RSM) was utilized for performing the experiments. Quadratic model to predict the MER and EWR were developed using response surface methodology. Discharge current has most significant effect of 50.176% and 36.36% on MER and EWR, respectively among all others process parameters. Teacher-learning-based optimization (TLBO) was employed for determining the optimal process parameters for maximum MER and minimal EWR. The results obtained with TLBO was compared with well-known optimization methods such as genetic algorithm (GA) and desirability function of RSM. Minimum EWR (0.1021 mm³/min) and maximum MER (30.4687 mm³/min) obtained using TLBO algorithm for optimized process parameters was found to better as compared to GA and desirability function.

Keywords

MFAPM-EDM material erosion rate electrode wear rate aluminium 6061 alloy teacher-learning-based optimization genetic algorithm desirability function

Get full access to this article

View all access options for this article.

References

Kuo

Hsu

Chen

, et al. Discharge current effect on machining characteristics and mechanical properties of aluminum alloy 6061 workpiece produced by electric discharging machining process. Adv Mech Eng 2017; 9: 1–8.

Akkurt

The effect of cutting process on surface microstructure and hardness of pure and Al 6061 aluminium alloy. Eng Sci Technol 2015; 18: 303–308.

Ishfaq

Ahmed

Rehman

, et al. WEDM of AA6061: an insight investigation of axial and lateral dimensional error. Mater Manuf Process 2020; 35: 762–774.

Sanchez

Rubio

Alvarez

, et al. Microstructural characterisation of material adhered over cutting tool in the dry machining of aerospace aluminium alloys. J Mater Process Technol 2005; 164–165: 911–918.

Thamban

Abraham

Kurian

Machining characteristics analysis of 6061-T6 aluminium alloy with diamond coated and uncoated tungsten carbide tool. Int J Lat Res Sci Technol 2013; 2: 553–557.

Bédard

Jahazi

Songmene

Die-sinking EDM of Al6061-T6: interactions between process parameters, process performance, and surface characteristics. Int J Adv Manuf Technol 2020; 107: 333–342.

Zain

Ndaliman

Khan

, et al. Improving micro-hardness of stainless steel through powder-mixed electrical discharge machining. Proc IMechE, Part C: J Mechanical Engineering Science 2014; 228: 3374–3380.

Arooj

Shah

Sadiq

, et al. Effect of current in the EDM machining of aluminum 6061 T6 and its effect on the surface morphology. Arab J Sci Eng 2014; 39: 4187–4199.

Bisaria

Shandilya

Experimental studies on electrical discharge wire cutting performance of Ni-rich NiTi shape memory alloy. Mater Manuf Process 2018; 33: 977–985.

10.

Banh

Nguyen

Ngo

, et al. Characteristics optimization of powder mixed electric discharge machining using titanium powder for die steel materials. Proc IMechE, Part E: J Process Mechanical Engineering 2018; 232: 281–298.

11.

Kumar

Singh

, et al. Comparison of material transfer in electrical discharge machining of AISI H13 die steel. Proc IMechE, Part C: J Mechanical Engineering Science 2009; 223: 1733–1740.

12.

Marashi

Sarhan

AAD

Hamdi

Employing tinano-powder dielectric to enhance surface characteristics in electrical discharge machining of AISI D2 steel. Appl Surf Sci 2015; 357: 892–907.

13.

Pramanik

Basak

Islam

, et al. Electrical discharge machining of 6061 aluminium alloy. Trans Nonferr Met Soc China 2015; 25: 2866–2874.

14.

Bisaria

Shandilya

Machining of metal matrix composites by EDM and its variants: a review. Vienna: DAAAM International Scientific Book. 2015, Chapter 23, pp. 267–282.

15.

Sahu

Datta

Experimental studies on graphite powder-mixed electro-discharge machining of Inconel 718 super alloys: comparison with conventional electro-discharge machining. Proc IMechE, Part E: J Process Mechanical Engineering 2018; 233: 384–402.

16.

Rouniyar

Shandilya

Multi-Objective optimization using Taguchi and grey relational analysis on machining of Ti-6Al-4V alloy by powder mixed EDM process. Mater Today Proc 2018; 5: 23779–23789.

17.

Bhatt

Batish

Bhattacharya

Experimental investigation of magnetic field assisted powder mixed electric discharge machining. Part Sci Technol 2015; 33: 1–28.

18.

Rouniyar

Shandilya

Fabrication and experimental investigation of magnetic field assisted powder mixed electrical discharge machining on machining of aluminum 6061 alloy. Proc IMechE, Part B: J Engineering Manufacture 2019; 233: 2283–2291.

19.

Bains

Sidhu

Payal

, et al. Magnetic field influence on surface modifications in powder mixed EDM. Silicon 2019; 11: 415–423.

20.

Rouniyar

Shandilya

Improvement in machined surface with the use of powder and magnetic field assisted on machining aluminium 6061 alloy with EDM. Iop Conf Ser Mater Sci Eng 2019; 647: 012002.

21.

Kant

Experimental investigation of magnetic field on EDM process by using Taguchi method on EN-19 tool steel. Glob J Res Eng 2015; 15: 27–35.

22.

Behera

Satapathy

Ghadai

SK.

Parameter optimisation of powder mixed EDM of aluminium-based metal matrix composite using Taguchi and grey analysis parameter optimization of powder mixed EDM of aluminium-based MMC. Int J Product Qual Manag 2015; 16: 148–168.

23.

Baseri

Sadeghian

Effects of nano powder TiO2-mixed dielectric and rotary tool on EDM. Int J Adv Manuf Technol 2016; 83: 519–528.

24.

Heinz

Kapoor

Devor

, et al. An investigation of magnetic- field-assisted material removal in micro-EDM for nonmagnetic materials. J Manuf Sci Eng 2011; 133: 021002–021001.

25.

Joshi

AY.

A systematic review on powder mixed electrical discharge machining. Heliyon 2019; 5: e02963.

26.

Assarzadeh

Ghoreishi

A dual response surface-desirability approach to process modeling and optimization of Al2O3 powder-mixed electrical discharge machining (PMEDM) parameters. Int J Adv Manuf Technol 2013; 64: 1459–1147.

27.

Kung

Horng

Chiang

KT.

Material removal rate and electrode wear ratio study on the powder mixed electrical discharge machining of cobalt-bonded tungsten carbide. Int J Adv Manuf Technol 2009; 40: 95–104.

28.

Rao

RV.

Review of applications of TLBO algorithm and a tutorial for beginners to solve the unconstrained and constrained optimization problems. Dec Sci Let 2016; 5: 1–30.

29.

Rao

RV.

Teaching learning based optimization algorithm and its engineering applications. Cham: Springer, 2016.

30.

Shandilya

Rouniyar

Saikiran

Multi-objective parametric optimization on machining of inconel-825 using wire electrical discharge machining. Proc IMechE, Part C: J Mechanical Engineering Science 2020; 234: 4056–4068.

31.

Biswal

Roy

Behera

RK.

Genetic algorithm- and finite element-based design and analysis of nonprismatic piezolaminated beam for optimal vibration energy harvesting. Proc IMechE, Part C: J Mechanical Engineering Science 2016; 230: 2532–2548.

32.

Cho

Park

SH.

Optimization in multiple response models with modified desirability function. Asian J Qual 2006; 7: 46–57.

33.

Candioti

Zan

MMD

Cámara

, et al. Experimental design and multiple response optimization using the desirability function in analytical methods development. Talanta 2014; 124: 123–138.