Hybrid Laser-Arc Welding (HLAW) is a relatively new joining technique that combines advantages from both laser beam welding and arc welding. The interaction between laser beam and arc welding provides advantageous synergic effects, especially for thick joints. On the other hand, this interaction brings extra complexity to HLAW, limiting its acceptance in industry. Therefore, it is still necessary to elucidate some features of HLAW, such as the influence of parameters and consumables on the characteristics of the resulting joints. In the present study, the effects of welding gases (Ar + CO2 in different proportions) and filler metals (solid and flux-cored wires) on thick S355 structural steel joints are assessed. The best welds in terms of geometric characteristics, microstructures, and mechanical behavior were fabricated with high CO2 content welding gases and flux-cored welding wires. The use of flux-cored wires promoted higher penetration, lower hardness, and formation of acicular ferrite, avoiding the formation of martensite encountered in joints welded with solid wires. Moreover, the application of flux-cored wires could lead to cost savings in future applications, by reducing the laser power required to produce sound joints.
SokolovMSalminenAKuznetsovM, et al.
Laser welding and weld hardness analysis of thick section S355 structural steel. Mater Des2011;
32: 5127–5131.
2.
PapaefthymiouSA.Root cause analysis of surface and internal defects of micro-alloyed S355 heavy plates. Int J Struct Integrity2013;
4: 91–107.
3.
AgrawalBPKumarR.Challenges in application of pulse current gas metal arc welding process for preparation of weld joint with superior quality. Int J Eng Res Technol2016;
5: 319–327.
4.
RaoZHLiaoSMTsaiHL.Modelling of hybrid laser–GMA welding: review and challenges. Sci Technol Weld Join2011;
16: 300–305.
5.
SathiyaPMishraMKShanmugarajanB.Effect of shielding gases on microstructure and mechanical properties of super austenitic stainless steel by hybrid welding. Mater Des2012;
33: 203–212.
6.
PetringD.Developments in hybridisation and combined laser beam welding technologies. In: KatayamaS (ed.) Handbook of laser welding technologies.
Woodhead Publishing Series in Electronic and Optical Materials, Cambridge:
Woodhead Publishing, 2013, pp. 478–504.
7.
UntAPoutiainenISalminenA.Influence of filler wire feed rate in laser-arc hybrid welding of T-butt joint in shipbuilding steel with different optical setups. Phys Proc2015;
78: 45–52.
8.
PalKPalSK.Effect of pulse parameters on weld quality in pulsed gas metal arc welding: a review. J Mater Eng Perform2011;
20: 918–931.
9.
NguyenTCWeckmanDCJohnsonDA.The discontinuous weld bead defect in high-speed gas metal arc welds. Weld J2007;
86: 360s–372s.
10.
BogueR.Fifty years of the laser: its role in material processing. Assem Autom2010;
30: 317–322.
11.
BogueR.Lasers in manufacturing: a review of technologies and applications. Assem Autom2015;
35: 161–165.
12.
SathiyaPAbdul JaleelMYKatherasanD, et al.
Optimization of laser butt welding parameters with multiple performance characteristics. Opt Laser Technol2011;
43: 660–673.
13.
MoorePLHowseDSWallachER.Microstructures and properties of laser/arc hybrid welds and autogenous laser welds in pipeline steels. Sci Technol Weld Join2004;
9: 314–322.
14.
Le GuenEFabbroRCarinM, et al.
Analysis of hybrid Nd:Yag laser-MAG arc welding processes. Opt Laser Technol2011;
43: 1155–1166.
15.
LiuSLiuFZhangH, et al.
Analysis of droplet transfer mode and forming process of weld bead in CO2 laser MAG hybrid welding process. Opt Laser Technol2012;
44: 1019–1025.
16.
RoepkeCLiuSKellyS, et al.
Hybrid laser arc welding process evaluation on DH36 and EH36 steel. Weld J2010;
89: 140s–150s.
17.
BaggerCOlsenFO.Review of laser hybrid welding. J Laser Appl2005;
17: 2–14.
18.
ErikssonIPowellJKaplanA.Guidelines in the choice of parameters for hybrid laser arc welding with fiber lasers. Phys Proc2013;
41: 119–127.
19.
KahP.Overview of the exploration status of laser-arc hybrid welding processes. Rev Adv Mater Sci2012;
30: 112–132.
20.
CasalinoGDal MasoUAngelastroA, et al. Hybrid laser welding: a review. In: KatalinicB (ed.) DAAAM international scientific book 2010.
Vienna:
DAAAM International, 2010, pp. 413–430.
21.
WahbaMMizutaniMKatayamaS.Hybrid welding with fiber laser and CO2 gas shielded arc. J Mater Process Technol2015;
221: 146–153.
22.
KahPSalminenAMartikainenJ.The analysis of shielding gases in laser-arc hybrid welding processes. Proc IMechE, Part B: J Engineering Manufacture2011;
225: 1073–1082.
23.
LorenzSKannengiesserTHeroldH, et al.
Suitability of high alloyed wire electrodes for the positional laser-GMA-hybrid welding. IJMMP2010;
5: 245–260.
24.
BabuSSDavidSA.Inclusion formation and microstructure evolution in low alloy steel welds. ISIJ Int2002;
42: 1344–1353.
25.
ChenYFengJLiL, et al.
Microstructure and mechanical properties of a thick-section high-strength steel welded joint by novel double-sided hybrid fibre laser-arc welding. Mater Sci Eng A2013;
582: 284–293.
26.
LiuSLiYLiuF, et al.
Effects of relative positioning of energy sources on weld integrity for hybrid laser arc welding. Opt Lasers Eng2016;
81: 87–96.
27.
GaoMZengXHuQ, et al.
Weld microstructure and shape of laser–arc hybrid welding. Sci Technol Weld Join2008;
13: 106–113.
28.
GaoMZengXYanJ, et al.
Microstructure characteristics of laser-MIG hybrid welded mild steel. Appl Surf Sci2008;
254: 5715–5721.
29.
ZhenSDuanZSunD, et al.
Study on microstructures and mechanical properties of laser-arc hybrid welded S355J2W+N steel. Opt Laser Technol2014;
59: 11–18.
30.
WahbaMMizutaniMKatayamaS.Single pass hybrid laser-arc welding of 25 mm thick square groove butt joints. Mater Des2016;
97: 1–6.
31.
ThewlisG.Classification and quantification of microstructures in steels. Mater Sci Technol2004;
20: 143–160.
32.
ISO 41362012. Destructive tests on welds in metallic materials – transverse tensile test.
33.
ASTM E3842016. Standard test method for microindentation hardness of materials.
34.
GaoWWangDChengF, et al.
Microstructural and mechanical performance of underwater wet welded S355 steel. J Mater Process Technol2016;
238: 333–340.
35.
ISO 12932:2013. Welding – laser-arc hybrid welding of steels, nickel and nickel alloys – quality levels for imperfections.
36.
ChungBRheeSLeeC.The effect of shielding gas types on CO2 laser tailored blank weldability of low carbon automotive galvanized steel. Mater Sci Eng A1999;
272: 357–362.
37.
GaoMChenCHuM, et al.
Characteristics of plasma plume in fiber laser welding of aluminum alloy. Appl Surf Sci2015;
326: 181–186.
38.
BoseS. Oxidation- and corrosion-resistant coatings. In: High temperature coatings. Amsterdam: Elsevier, 2018, pp.97–198.
39.
AbbottDHAlbrightCE.CO2 shielding gas effects in laser welding mild steel. J Laser Appl1994;
6: 69–80.
40.
KatayamaSKawahitoYMizutaniM.Elucidation of laser welding phenomena and factors affecting weld penetration and welding defects. Phys Procedia2010;
5: 9–17.
41.
JokarMMalekGhainiFTorkamanyMJ, et al.
Influence of shielding gas composition on weld profile in pulsed Nd:YAG laser welding of low carbon steel. Iran J Phys Res2014;
14: 41–46.
42.
MendezPFEagarTW.Penetration and defect formation in High-Current arc welding. Weld J2003;
82: 296s–306s.
43.
FrostevargJKaplanAFH.Undercuts in laser arc hybrid welding. Phys Proc2014;
56: 663–672.
44.
LyttleKA, et al. Shielding gases for welding. In: OlsonDLSiewertTALiuS (eds) Welding, brazing and soldering.
Cleveland:
ASM International, 1993, pp.64–69.
45.
MatsudaFNakagawaHUeyamaT.Solidification crack susceptibility in laser beam weld metal of 0.2C-low alloy steels-effect of bead configuration and S and P contents. Trans JWRI1987;
16: 103–114.
46.
GebhardtMOGumenyukARethmeierM.Solidification cracking in laser GMA hybrid welding of thick-walled parts. Sci Technol Weld Join2014;
19: 209–213.
47.
XuGXWuCSQinGL, et al.
Adaptive volumetric heat source models for laser beam and laser + pulsed GMAW hybrid welding processes. Int J Adv Manuf Technol2011;
57: 245–255.
48.
LiuATangXLuF.Weld pool profile characteristics of Al alloy in double-pulsed GMAW. Int J Adv Manuf Technol2013;
68: 2015–2023.
49.
El RayesMWalzCSepoldG.The influence of various hybrid welding parameters on bead geometry. Weld J2004; : 147–s-153. s.
50.
CampanaGFortunatoAAscariA, et al.
The influence of arc transfer mode in hybrid laser-mig welding. J Mater Process Technol2007;
191: 111–113.
51.
KatayamaSUchiumiSMizutaniM, et al.
Penetration and porosity prevention mechanism in YAG laser-MIG hybrid welding. Weld J2007;
21: 25–31.
52.
ZhaoLTsukamotoSArakaneG, et al.
Prevention of porosity by oxygen addition in fibre laser and fibre laser–GMA hybrid welding. Sci Technol Weld Join2014;
19: 91–97.
53.
Mazar AtabakiMMaJLiuW, et al.
Pore formation and its mitigation during hybrid laser/arc welding of advanced high strength steel. Mater Des2015;
67: 509–521.
54.
GhazvinlooHR.Effect of the electrode to work angle, filler diameter and shielding gas type on weld geometry of HQ130 steel joints produced by robotic GMAW. IJST2010;
3: 26–30.
55.
SchafranskiLLda CunhaTVBohórquezCEN.Benefits from H2 and CO2 additions in argon gas mixtures in GMAW. J Mater Process Technol2017;
249: 158–166.
56.
TusekJSubanM.Experimental research of the effect of hydrogen in argon as a shielding gas in arc welding of high-alloy stainless steel. Int J Hydrogen Energy2000;
25: 369–376.
57.
ShanpingLHidetoshiFKiyoshiN.Effects of CO2 shielding gas additions and welding speed on GTA weld shape. J Mater Sci2005;
40: 2481–2485.
58.
CaiXFanCLinS, et al.
Effects of shielding gas composition on arc behaviors and weld formation in narrow gap tandem GMAW. Int J Adv Manuf Technol2017;
91: 3449–3456.
59.
MvolaBKahP.Effects of shielding gas control: welded joint properties in GMAW process optimization. Int J Adv Manuf Technol2017;
88: 2369–2387.
60.
Kaplan AFH, Mizutani M, Katayama S, et al. Mechanism of pore formation during keyhole laser spot welding. In: Proceedings of SPIE 4831, First International Symposium on High-Power Laser Macroprocessing, 3 March 2003. https://doi.org/10.1117/12.497914.
61.
LiuWMaJYangG, et al.
Hybrid laser-arc welding of advanced high-strength steel. J Mater Process Technol2014;
214: 2823–2833.
62.
DavidSAVitekJM.Correlation between solidification parameters and weld microstructures. Int Mater Rev1989;
34: 213–245.
63.
GrongOMatlockDK.Microstructural development in mild and low-alloy steel weld metals. Int Met Rev1986;
31: 27–48.
64.
CuiLYangXWangD, et al.
Friction taper plug welding for S355 steel in underwater wet conditions: welding performance, microstructures and mechanical properties. Mater Sci Eng A2014;
611: 15–28.
65.
SantosTFTorresEALVilelaJMC, et al.
Microstructural characterization of low carbon steels by atomic force microscopy. Rev Lat Met Mat2015;
35: 118–133.
66.
GrünenwaldSSeefeldTVollertsenF, et al.
Solutions for joining pipe steels using laser-GMA-hybrid welding processes. Phys Procedia2010;
5: 77–87.
67.
RibicBRaiRDebRoyT.Numerical simulation of heat transfer and fluid flow in GTA/laser hybrid welding. Sci Technol Weld Join2008;
13: 683–693.
68.
WeiHLBlecherJJPalmerTA, et al.
Fusion zone microstructure and geometry in complete-joint – penetration laser-arc hybrid welding of low-alloy steel. Weld J2015;
94: 135-s–144s.
