Strain measurement and error analysis in thermo-mechanical tensile tests of sheet metals for hot stamping applications

Abstract

In order to conduct uniaxial tensile tests for hot stamping applications, tests are normally performed by using a Gleeble thermo-mechanical materials simulator so that rapid heating and cooling processes can be obtained. However, temperature gradients in a specimen tested on Gleeble are inevitable due to resistance heating principles and heat loss to grips and water-cooled jaws. In this research, a pair of purpose-built grips made of stainless steel with low thermal conductivity and significantly reduced contacting area for clamping, as well as a flat dog-bone specimen with maximised parallel length (80 mm) were designed, for the purpose of improving the temperature uniformity within the concerned gauge section area of the specimen. Uniaxial tensile tests on AA6082 were performed, after controlled heating and cooling processes, at constant deformation temperatures in the range of 400 ℃–500 ℃ and at constant strain rate in the range of 0.1–4/s, to simulate its hot stamping conditions. The digital image correlation system was adopted to enable strain distributions in specimens to be measured. The temperature distributions in specimens were investigated and an effective gauge length of 14 mm was specified accordingly to ensure temperature gradients less than 10 ℃ within it at all tested temperatures. True stress–true strain curves of AA6082 were obtained based on results of strain measurements along the defined effective gauge length and used to calibrate a set of advanced material model. Error analysis was carried out by using thermo-electrical and thermo-mechanical FE models on ABAQUS, in which the calibrated material constitutive equations were implemented via subroutines. The error of stress–strain curves of AA6082 measured based on the specified gauge length was investigated and quantified by analysing the distribution of axial strain and axial stress.

Keywords

Strain measurement hot stamping thermo-mechanical testing uniaxial tensile test sheet metal forming

Get full access to this article

View all access options for this article.

References

Metallic materials – tensile testing – part 1: method of test at ambient temperature. International Organization for Standardization. ISO 6892-1:2009.

Tensile testing of metallic materials – part 5: method of test at elevated temperatures. International Organization for Standardization. ISO 6892-2:2011.

Test methods for conducting creep, creep-rupture, and stress-rupture tests of metallic materials, West Conshohocken, United States: ASTM International, 2006.

Karbasian

Tekkaya

. A review on hot stamping. J Mater Process Technol 2010; 210: 2103–2118.

Foster A, Dean TA and Lin J. Process for forming aluminium alloy sheet component. UK Patent Office, UK, 2012.

Ghosh

. Tensile deformation behavior of aluminum alloys at warm forming temperatures. Mater Sci Eng A 2003; 352: 279–286.

Yang

Degischer

H-P

Presslinger

et al.

Influence of chemical composition on high temperature tensile properties of carbon steels. BHM Berg-und Hüttenmännische Monatshefte 2005; 150: 313–320.

Bok

Lee

M-G

Kim

H-D

et al.

Thermo-mechanical finite element analysis incorporating the temperature dependent stress-strain response of low alloy steel for practical application to the hot stamped part. Metals Mater Int 2010; 16: 185–195.

Gui

Liang

Liu

et al.

Thermo-mechanical behavior of the Al–Si alloy coated hot stamping boron steel. Mater Design 2014; 60: 26–33.

10.

Lee

Lin

Chien

. Experimental and theoretical studies on formability of 22MnB5 at elevated temperatures by Gleeble simulator. Procedia Eng 2014; 81: 1682–1688.

11.

Abspoel

Neelis

van Liempt

. Constitutive behaviour under hot stamping conditions. J Mater Process Technol 2015; 228: 34–42.

12.

Lindeman NA. Technique for applying direct resistance heating current to a specific location in a specimen under test while substantially reducing thermal gradient. US Patent, 2008.

13.

Shao

Bai

et al.

Experimental investigation of forming limit curves and deformation features in warm forming of an aluminium alloy. Proc IMechE, Part B: J Engineering Manufacture 2016, pp. 1–10.

14.

Sun

Guo

Momhamed

et al.

Damage investigation of boron steel at hot stamping conditions. Procedia Eng 2014; 81: 1744–1749.

15.

Dumoulin

Louche

Hopperstad

et al.

Heat sources, energy storage and dissipation in high-strength steels: experiments and modelling. Eur J Mech A/Solids 2010; 29: 461–474.

16.

Knorovsky

Robino

Dykhuizen

et al.

Dilatometry in the Gleeble: what did you really measure?, Albuquerque: Sandia National Labs, 1998.

17.

Vacher

Dumoulin

Morestin

et al.

Bidimensional strain measurement using digital images. Proc IMechE, Part C: J Mechanical Engineering Science 1999; 213: 811–817.

18.

Lecompte

Cooreman

Coppieters

et al.

Parameter identification for anisotropic plasticity model using digital image correlation. Eur J Comput Mech 2009; 18: 393–418.

19.

Pottier

Toussaint

Vacher

. Contribution of heterogeneous strain field measurements and boundary conditions modelling in inverse identification of material parameters. Eur J Mech A/Solids 2011; 30: 373–382.

20.

Merklein

Lechler

. Investigation of the thermo-mechanical properties of hot stamping steels. J Mater Process Technol 2006; 177: 452–455.

21.

Zhou

Hayden

Gao

. An investigation of the strain rate and temperature effects on the plastic flow stress and ductile failure strain of aluminum alloys 5083-H116, 6082-T6 and a 5183 weld metal. Proc IMechE, Part C: J Mechanical Engineering Science 2012; 227: 883–895.

22.

Garrett

Lin

Dean

. An investigation of the effects of solution heat treatment on mechanical properties for AA 6xxx alloys: experimentation and modelling. Int J Plasticity 2005; 21: 1640–1657.

23.

Mohamed

Foster

Lin

et al.

Investigation of deformation and failure features in hot stamping of AA6082: experimentation and modelling. Int J Mach Tools Manuf 2012; 53: 27–38.

24.

Khaleel

Zbib

Nyberg

. Constitutive modeling of deformation and damage in superplastic materials. Int J Plasticity 2001; 17: 277–296.

25.

El Fakir

Wang

Balint

et al.

Numerical study of the solution heat treatment, forming, and in-die quenching (HFQ) process on AA5754. Int J Mach Tools Manuf 2014; 87: 39–48.

26.

Lin

. Fundamentals of materials modelling for metals processing technologies: theories and applications, London, the United Kingdom: Imperial College Press, 2015.

27.

Kaufman

. Properties of aluminum alloys: tensile, creep, and fatigue data at high and low temperatures, Ohio, United States: ASM International, 1999.

28.

Shao

Lin

et al.

Development of a new biaxial testing system for generating forming limit diagrams for sheet metals under hot stamping conditions. Exp Mech 2016; 56: 1489–1500.