Dynamic analysis of gearbox behaviour in milling process: Non-stationary operations

Abstract

Dynamic behaviour of gearbox transmitting power to milling tool in a milling process application is considered in this paper. The gearbox is subjected to variable cutting torque induced by the milling operation. This variability will lead to fluctuating speed. The dynamic behaviour of the system should be investigated according to this non-stationary operating condition. To achieve this objective, a simple model of motor-gearbox-milling tool system is developed. The influence of variable cutting torque on driving motor speed is taken into account. The gearmesh function which describes the meshing phenomena is modified according to this specific operating condition. Simulations of the dynamic behaviour of the gearbox show a simultaneous frequency and amplitude modulation. These modulations are highlighted using time frequency representation which is necessary to implement so that it is possible to achieve a correct diagnosis of the transmission. Simulations in presence of tooth crack defect confirmed the necessity to implement time frequency techniques to characterize time varying systems.

Keywords

Milling non-stationary operation gearbox fluctuating load crack

Get full access to this article

View all access options for this article.

References

Bartelmus

Zimroz

. Vibration condition monitoring of planetary gearbox under random varying. Mech Syst Signal Process 2009; 23: 246–257.

Bartelmus

Zimroz

. A new feature for monitoring the condition of gearboxes in non-stationary operating conditions. Mech Syst Signal Process 2010; 29: 637–646.

Randall

. A new method of modelling gear faults. J Mech Des 1982; 104: 259–267.

Stander

Heyns

Schoombie

. Using vibration monitoring for local fault detection on gears operating under fluctuating load conditions. Mech Syst Signal Process 2002; 16: 1005–1024.

Baydar

Ball

. Detection of gear deterioration under varying load conditions by using the instantaneous power spectrum. Mech Syst Signal Process 2000; 14: 907–921.

Combet

Zimroz

. A new method for the estimation of the instantaneous speed relative fluctuation in a vibration signal based on the short time scale transform. Mech Syst Signal Process 2009; 23: 1382–1397.

Zhan

Makis

Jardine

AKS

. Adaptive state detection of gearboxes under varying load conditions based on parametric modelling mechanical. Mech Syst Signal Process 2006; 20: 188–221.

Khabou

Bouchaala

Chaari

. Study of a spur gear dynamic behavior in transient regime. Mech Syst Signal Process 2011; 25: 3089–3101.

Chaari

Leskow

Napolitano

. Gearbox vibration signal amplitude and frequency modulation. Shock Vibration 2012; 19: 635–652.

10.

Smith S and Tlusty J. An overview of the modelling and simulation of the milling process. ASME J Manuf Sci Eng 1991; 113: 169–175.

11.

Altintas

Lee

. A general mechanics and dynamics model for helical end mills. CIRP Ann Manuf Technol 1996; 45(1): 59–64.

12.

Nee

AYC

Wong

. Theoretical modelling and simulation of milling forces. J Mater Process Technol 1999; 266–272: 89–90.

13.

Zheng

Wong

. Theoretical modelling and simulation of cutting forces in face milling with cutter runout. Int J Machine Tools Manuf 1999; 39: 3–18.

14.

Engin

Altintas

. Mechanics and dynamics of general milling cutters: Part ii: inserted cutters. Int J Machine Tools Manuf 2001; 41: 2213–2231.

15.

Koenigsberger

Sabberwal

AJP

. An investigation into the cutting force pulsations during milling operations. Int J Machine Tool Des Res 1961; 1: 15–33.

16.

Budak

Altintas

. Peripheral milling conditions for improved dimensional accuracy. Int J Machine Tool Des Res 1994; 34: 907–918.

17.

Budak

Altintas

. Modeling and avoidance of static deformations in peripheral milling of plates. Int J Machine Tool Des Res 1995; 35: 459–476.

18.

Velex P. Contribution à L’analyse du Comportement Dynamique de Réducteurs à Engrenages à Axes Parallèles, PhD, INSA Lyon, France, 1988.

19.

Altintas Y. Machine tool dynamics and vibrations. In: OOI Nwokah and Y Hurmuzlu (eds) The Mechanical systems design handbook: modeling, measurement and control. CRC Press LLC, 2002, pp.76–88.

20.

Chaari

Baccar

Abbes

. Effect of spalling or tooth breakage on gearmesh stiffness and dynamic response of a one-stage spur gear transmission. Eur J Mech A/Solids 2008; 27: 691–705.

21.

Åkesson H, Smirnova T, Håkansson L, et al. Investigation of the dynamic properties of a milling tool holder. Blekinge Institute of Technology Research report No. 2009:07, 2009.

22.

Åkesson H, Smirnova T, Håkansson L, et al. Investigation of the dynamic properties of a milling structure; using a tool holder with moderate overhang. In: Proceedings of the IMAC-XXVII, Orlando, FL, 9–12 February 2009.

23.

Randall

. A new method of modelling gear faults. J Mech Des 1982; 104: 259–267.

24.

Sadettin

Nizami

Veli

. Vibration monitoring for defect diagnosis of rolling element bearings as a predictive maintenance tool: comprehensive case studies. NDT&E Int 2006; 39: 293–298.

25.

Fakhfakh

Chaari

Haddar

. Numerical and experimental analysis of gear system with teeth defects. Int J Adv Manuf Technol 2005; 25: 542–550.