Thermodynamic peculiarities of alpha-type Stirling engines for low-temperature difference power generation: Optimisation of operating parameters and heat exchangers using a third-order model

Abstract

Low-temperature heat sources such as waste heat and geothermal energy in the range from 100 ℃ to 200 ℃ are widely available and their potential is largely untapped. Stirling engines are one possibility to convert this heat to a usable power output. Much work has been done to optimise Stirling engines for high-temperature heat sources such as external combustion or concentrated solar energy but only little is known about suitable engine layouts at lower temperature differences. With the reduced temperature difference, changes become necessary not only in the heat exchangers and the regenerator but also in the operating parameters such as frequency and phase angle. This paper shows results obtained from a third-order simulation model that help to identify beneficial parameter combinations, and explains the differences of low and high-temperature engines.

Keywords

Low-temperature power generation Stirling engine piston type power optimisation third-order modelling waste-heat geothermal energy design

Get full access to this article

View all access options for this article.

References

Aneke

Agnew

Underwood

. Performance analysis of the Chena binary geothermal power plant. Appl Thermal Eng 2011; 31: 1825–1832.

DiPippo R. Geothermal power plants: principles, applications, case studies and environmental impact. Oxford: Elsevier, 2007.

Quoilin

Aumann

Grill

. Dynamic modeling and optimal control strategy of waste heat recovery Organic Rankine Cycles. Appl Energy 2011; 88: 2183–2190.

Senft JR. Mechanical efficiency of heat engines. Cambridge University Press, 2007.

Walker G. Stirling engines. Clarendon Press, 1980.

West CD. Principles and applications of Stirling engines. Van Nostrand Reinhold Company, 1986.

Hargreaves CM. The Philips Stirling engine. Elsevier, 1991.

Stirling DK homepage. http://www.stirling.dk (accessed 23 May 2013).

Infinia homepage. http://www.infiniacorp.com/en/home/ (accessed 21 May 2013).

10.

Efficient Home Energy (EHE) homepage. http://www.whispergen.com (accessed 7 December 2010).

11.

Microgen homepage. http://www.microgen-engine.com/ (accessed 23 January 2013).

12.

Cleanergy homepage. http://www.cleanergy.com/ (accessed 23 January 2013).

13.

Thomas

. Benchmark testing of micro-CHP units. Appl Thermal Eng 2008; 28: 2049–2054.

14.

De Paepe

D’ Herdt

. Micro-CHP systems for residential applications. Energy Convers Manage 2006; 47: 3435–3446.

15.

Onovwiona

Ugursal

. Residential cogeneration systems: review of the current technology. Renew Sustain Energy Rev 2006; 10: 389–431.

16.

Takeuchi M, Suzuki S, Abe Y, et al. Development of 1 kW class low temperature difference indirect heating Stirling engine using alpha+ type mechanism. In: Proceedings of the 13th international Stirling engine conference ISEC, Tokyo, 2007.

17.

Takeuchi M, Abe Y, et al. Development of 10 kW class low temperature difference indirect heating Stirling Engine using alpha+ type mechanism. In: Proceedings of the 13th international Stirling engine conference ISEC, 2007.

18.

Kongtragool

Wongwises

. Performance of low-temperature differential Stirling engines. Renew Energy 2007; 32: 547–566.

19.

Tveit TM, Hoeg A and Asphjell TA. A prototype alpha Stirling engine for low temperature heat recovery power generation. In: Proceedings of the 13th international Stirling engine conference ISEC, 2007.

20.

Tveit TM, Hoeg A and Asphjell TA. A simulation based interactive multi-criterion strategy for optimising Stirling-engine designs. In: ISEC2009 – The 14th international Stirling engine conference, Groningen, the Netherlands, 2009.

21.

Hoegel B, Pons D, Gschwendtner M, et al. Theoretical investigation of the performance of an Alpha Stirling engine for low temperature applications. In: Proceedings of the 15th international Stirling engine conference (ISEC), 2012.

22.

Finkelstein T and Organ AJ. Air engines. London: Professional Engineering Publishing Limited, 2001.

23.

Walker

. An optimization of the principal design parameters of Stirling cycle machines. Proc IMechE, Part C. Journal Mechanical Engineering Science 1962; 4: 226–240.

24.

Kirkley

. Determination of the optimum configuration for a Stirling engine. Proc IMechE, Part C. Journal Mechanical Engineering Science 1962; 4: 204–212.

25.

Cheng

Yang

. Optimization of geometrical parameters for Stirling engines based on theoretical analysis. Appl Energy 2012; 92: 395–405.

26.

Batmaz

Üstün

. Design and manufacturing of a V-type Stirling engine with double heaters. Appl Energy 2008; 85: 1041–1049.

27.

Senft

. Optimum Stirling engine geometry. Int J Energy Res 2002; 26: 1087–1101.

28.

Gedeon D. Sage – object-oriented software for Stirling machine design. AIAA Paper 94-4106: 1902–1907, 1994.

29.

Gedeon D. Sage user’s guide. Athens: Gedeon Associates. http://sageofathens.com/ (2010, last accessed 6 November 2013).

30.

Demko R and Barry Penswick L. Sage simulation model for technology demonstration convertor by a step-by-step approach. In: Proceedings of the international energy conversion engineering conference (IECEC 2005), vol. 1, San Francisco, CA, USA, 2005, pp.270–289.

31.

Landis

Mellott

. Venus surface power and cooling systems. Acta Astronaut 2007; 61: 995–1001.

32.

Gupta

. Fundamentals of heat exchanger and pressure vessel technology, New York, NY: Hemisphere, 1986.

33.

Iwabuchi M and Kanzaka M. Experimental investigation into heat transfer under the periodically reversing flow condition in heat tube. In: Stirling engines – progress towards reality. London: I Mech E. Mechanical Engineering Publications, 1982. pp.77–85.