Register control of roll-to-roll gravure-offset printing equipment considering time difference between measurement and actuation

Abstract

The manufacture of printed electronics by roll-to-roll printing machine requires more accurate register performance than conventional media printing technology. Moreover, high drying temperature and long drying time to sinter the inks can induce the substantial changes in the length of the substrate and consequently register errors. Among the roll-to-roll printing methods, the gravure one, despite its relatively fast productivity and fine-line printing capacity, has difficulty in achieving the required register specifications for printed electronics because of the dependence of the register control on web dynamics. This study proposes a roll-to-roll gravure-offset printing equipment, including the register measurement system designed to enhance register performance and the related register control method for the application of printed electronics. Each cylinder constituting the printing unit is driven independently by an individual servomotor. Moreover, the printing patterns of the plate cylinder can move in the axial direction by position control, as well as in the web transport direction by a phase shift of the plate cylinder, without affecting the dynamics of the web. The time difference between the measurement and the actual control action is considered and modeled. The register measurement system, including selections of sensors and marks is also proposed to consider the effect of the time difference. The simulation results and the experiments of the register control are shown to verify the effect of the time difference on the control performances. It is found that a proper estimation of time difference should be obtained in order to guarantee more accurate and stable control performances.

Keywords

Roll-to-roll register control gravure-offset printed electronics time difference

Get full access to this article

View all access options for this article.

References

Shelton

Reid

. Lateral dynamics of an idealized moving web. ASME J Dyn Syst Meas Control 1971; 93(3): 187–192.

Young

Reid

. Lateral and longitudinal dynamic behavior and control of moving webs. ASME J Dyn Syst Meas Control 1993; 115(2): 309–317.

Komatsu H, Yoshida T, Takagi S, et al. Improvement of printing accuracy via web handling control in multi-colors printing machines. In: Proceedings of the international conference on control, automation and systems, Seoul, Korea, 17–20 October 2007, pp.953–956. Piscataway, NJ: IEEE.

Kang H-K, Eom Y-S, Lee J-M, et al. Compensation of register errors due to tension disturbances in printing presses. In: Proceedings of the 1st international conference on R2R printed electronics, Seoul, Korea, 30 April–2 May 2008, pp.165–170.

Kipphan

(ed.). Handbook of print media: technologies and production methods. New York, Heidelberg, Berlin: Springer-Verlag, 2001, pp. 372–372.

Kang

H-K

Lee

C-W

Shin

K-H

. A novel cross directional register modeling and feedforward control in multi-layer roll-to-roll printing. J Process Control 2010; 20: 643–652.

Kang

H-K

Lee

C-W

Shin

K-H

. Novel modeling of correlation between two-dimensional registers in large-area multilayered roll-to-roll printed electronics. Jpn J Appl Phys 2011; 50: 016701-1–016701-7.

Pesavento

Puntambekar

Frisbiea

. Film and contact resistance in pentacene thin-film transistors: dependence on film thickness, electrode geometry, and correlation with hole mobility. J Appl Phys 2006; 99: 4504–4513.

Choi

B-O

Kim

. Manufacturing ultra-high-frequency radio frequency identification tag antennas by multilayer printings. Proc IMechE Part C: J Mech Eng Sci 2010; 224(1): 149–156.

10.

Rebros M, Hrehorova E, Bazuin BJ, et al. Rotogravure printed UHF RFID antennae directly on packaging materials. In: Proceedings of the TAGA, San Francisco, CA, 16–19 March 2008, pp. 292–304.

11.

Hrehorova E, Pekarovicova A and Fleming PD. Evaluation of gravure printing for printed electronics. In: Proceedings of the TAGA, San Francisco, CA, 16–19 March 2008, pp. 324–336.

12.

Hrehorova E, Rebros M, Pekarovicova A, et al. Suitability of gravure printing for high volume fabrication of electronics. In: Proceedings of the DF08, Pittsburgh, PA, 7–12 September 2008, pp.260–264.

13.

Kattumenu R, Rebros M, Hrehorova E, et al. Evaluation of Flexographically Printed Conductive Traces on Paper Substrates. In: Proceedings of the TAGA, San Francisco, CA, 16–19 March 2008, pp.432–454.

14.

Brandenburg

Geibenberger

Klemm

. Noninteracting control of web force and cut-off register errors in rotary printing presses with electronic line shafts. EPE J 2003; 16(2): 38–44.

15.

Brandenburg G. New mathematical models for web tension and register error. In: Proceedings of the 3rd international IFAC conference on instrumentation and automation in the paper, rubber and plastics industry, Brussels, Belgium, 24–26 May 1976, Rubber and Plastics Industry, 1977, vol. 1, pp.411–438.

16.

Lee

Noh

J-H

Kim

. Development of a gravure offset printing system for the printing electrodes of flat panel display. Thin Solid Films 2010; 518(12): 3355–3359.

17.

Kim

H-Y

. Effects of blanket roller deformation on printing qualities in gravure-offset printing method. Jpn J Appl Phys 2010; 49(5): 05EC04–05EC04.

18.

Edwards CO, Howarth J and James A. Inkjet printing of high conductivity circuits on various substrates using polymer capped nano-particle silver. In: Proceedings of the IMID ’05 DIGEST, Seoul, Korea, 19–23 July 2005, pp.814–816.

19.

Shin

D-Y

Lee

Kim

. Performance characterization of screen printed radio frequency identification antennas with silver nanopaste. Thin Solid Films 2009; 517(21): 6112–6118.