In this study, KMnO4 was applied as an etchant to partially decompose the silica microspheres into mesoporous structures. 1H,1H,2H,2H-perfluorodecyltriethoxysilane was grafted onto the surface of the hollow silica. A fluorinated silica/polyimide hybrid material was prepared. Meanwhile, the influence of fluorinated silica on the dielectric property and moisture absorption property of the hybrid material was discussed. It is found that the fluorinated silica can lower the dielectric constant and hygroscopicity of the hybrid film. The fluorinated silica is characterized by strong hydrophobicity, good dispersibility, and good thermal stability. Even at a very low filling level of only 2 wt%, the dielectric constant of the polyimide hybrid is significantly reduced to 2.61 without sacrificing thermal stability. The water absorption rate of the polyimide hybrid film is reduced from approximately 3.1% to 2.1 wt%. Moreover, this provides a new idea for reducing the dielectric and water absorption properties of materials.
KimKJKimKSLeeNE, et al.Chemical interaction and adhesion characteristics at the interface of metals (Cu, Ta) and low-kcyclohexane-based plasma polymer (CHexPP) films. J Vacuum Sci Tech A2001; 19: 1072–1077. DOI: 10.1116/1.1340658.
2.
YangCYChenJSHsuSLC. Investigation of the interfacial reaction between metal and fluorine-contained polyimides. J Vacuum Sci Tech A2005; 23: 862–868. DOI: 10.1116/1.1868632.
3.
HongZDongyangWYongF, et al.Dielectric properties of polyimide/SiO2 hollow spheres composite films with ultralow dielectric constant. Mater Sci Eng B2016; 203: 13–18. DOI: 10.1016/j.mseb.2015.10.003.
4.
ZhangYKeSHuangH, et al.Dielectric relaxation in polyimide nanofoamed films with low dielectric constant. Appl Phys Lett2008; 92: 052910. DOI: 10.1063/1.2840715.
5.
John Pellerin RFaH-MH. Low dielectric constant fluorinated polyimides for interlayer dielectric applications. Mater Res Soc1997; 476: 1997.
6.
ZhouYWangLZhangH, et al.Enhanced high thermal conductivity and low permittivity of polyimide based composites by core-shell Ag@SiO2 nanoparticle fillers. Appl Phys Lett2012; 101: 012903. DOI: 10.1063/1.4733324.
7.
ZhangYHDangZMFuSY, et al.Dielectric and dynamic mechanical properties of polyimide-clay nanocomposite films. Chem Phys Lett2005; 401: 553–557. DOI: 10.1016/j.cplett.2004.11.084.
8.
LvPDongZDaiX, et al.Low-dielectric polyimide nanofoams derived from 4,4′-(hexafluoroisopropylidene)diphthalic anhydride and 2,2′-bis(trifluoromethyl)benzidine. RSC Adv2017; 7: 4848–4854. DOI: 10.1039/c6ra25604j.
9.
RenYLamDCC. Properties and microstructures of low-temperature-processable ultralow-dielectric porous polyimide films. J Electron Mater2008; 37: 955–961. DOI: 10.1007/s11664-008-0446-z.
10.
Terng ChernYShiueHC. Low dielectric constants of soluble polyimides based on adamantane. Macromolecules1997; 30: 4646–4651.
11.
Terng ChernYYu TsaiJ. Low dielectric constant and high organosolubility of novel polyimide derived from unsymmetric 1,4-bis(4-aminophenoxy)-2,6-di-tert-butylbenzene. Macromolecules2008; 41: 9556–9564.
PopoviciDHulubeiCCozanV, et al.Polyimides containing cycloaliphatic segments for low dielectric material. High Perform Polym2012; 24: 194–199. DOI: 10.1177/0954008311435798.
14.
TaoLYangHLiuJ, et al.Synthesis and characterization of highly optical transparent and low dielectric constant fluorinated polyimides. Polymer2009; 50: 6009–6018. DOI: 10.1016/j.polymer.2009.10.022.
15.
LiQWangYZhangS, et al.Novel fluorinated random co-polyimide/amine-functionalized zeolite MEL50 hybrid films with enhanced thermal and low dielectric properties. J Mater Sci2017; 52: 5283–5296. DOI: 10.1007/s10853-017-0768-4.
16.
CaiLFHuangXBRongMZ, et al.Effect of grafted polymeric foaming agent on the structure and properties of nano-silica/polypropylene composites. Polymer2006; 47: 7043–7050. DOI: 10.1016/j.polymer.2006.08.016.
17.
ChenZZhuDTongF, et al.Low dielectric constant polyimide hybrid films prepared by in situ blow-balloon method. ACS Appl Polym Mater2019; 1: 2189–2196. DOI: 10.1021/acsapm.9b00448.
18.
ChoSYLeeCHOhSY, et al.Preparation and characterization of nanoporous polyimide films from triblock copolyimides. Ultramicroscopy2008; 108: 1220–1223. DOI: 10.1016/j.ultramic.2008.04.018.
19.
ZouYZhanYZhaoR, et al.Low dielectric permittivity and high thermal stability composites based on crosslinkable poly (arylene ether nitrile) and hollow glass microsphere. J Mater Sci Mater Electro2012; 24: 1238–1242. DOI: 10.1007/s10854-012-0913-4.
20.
ZhangYYuLSuQ, et al.Fluorinated polyimide-silica films with low permittivity and low dielectric loss. J Mater Sci2011; 47: 1958–1963. DOI: 10.1007/s10853-011-5990-x.
21.
ShiXSanedrinRZhouF, et al.Formation of uniform polyaniline thin shells and hollow capsules using polyelectrolyte-coated microspheres as templates. Macromolecules2003; 36: 4093–4098.
22.
YungKZhuBYueT, et al.Preparation and properties of hollow glass microsphere-filled epoxy-matrix composites. Composites Sci Tech2009; 69: 260–264. DOI: 10.1016/j.compscitech.2008.10.014.
23.
PatankarSNDasAKranovYA. Interface engineering via compatibilization in HDPE composite reinforced with sodium borosilicate hollow glass microspheres. Comp A Appl Sci Manuf2009; 40: 897–903. DOI: 10.1016/j.compositesa.2009.04.016.
24.
YamazakiOYamashitaTHorieKazuyuki. Preparation and properties of poly(amide acid) gels. Reactive Funct Polym2000; 43: 173–181.
25.
ZhouHLeiHWangJ, et al.Breaking the mutual restraint between low permittivity and low thermal expansion in polyimide films via a branched crosslink structure. Polymer2019; 162: 116–120. DOI: 10.1016/j.polymer.2018.12.033.
26.
GengZBaJZhangS, et al.Ultra low dielectric constant hybrid films via side chain grafting reaction of poly(ether ether ketone) and phosphotungstic acid. J Mater Chem2012; 22: 23534. DOI: 10.1039/c2jm35040h.
27.
WangLNiJLiuD, et al.Effects of branching structures on the properties of phosphoric acid-doped polybenzimidazole as a membrane material for high-temperature proton exchange membrane fuel cells. Int J Hydrogen Energ2018; 43: 16694–16703. DOI: 10.1016/j.ijhydene.2018.06.181.
28.
DinariMAsadiPKhajehS. In situ thermal synthesis of novel polyimide nanocomposite films containing organo-modified layered double hydroxide: morphological, thermal and mechanical properties. New J Chem2015; 39: 8195–8203. DOI: 10.1039/c5nj01640a.
29.
DinariMRajabiAR. Structural, thermal and mechanical properties of polymer nanocomposites based on organosoluble polyimide with naphthyl pendent group and layered double hydroxide. High Perform Polym2016; 29: 951–959. DOI: 10.1177/0954008316665678.
30.
MallakpourSDinariM. Fabrication of polyimide/titania nanocomposites containing benzimidazole side groups via sol-gel process. Prog Org Coat2012; 75: 373–378. DOI: 10.1016/j.porgcoat.2012.07.012.
31.
MallakpourSDinariM. Polymer/organosilica nanocomposites based on polyimide with benzimidazole linkages and reactive organoclay containing isoleucine amino acid: synthesis, characterization and morphology properties. Mater Res Bull2012; 47: 2336–2343. DOI: 10.1016/j.materresbull.2012.05.033.
32.
Mohammad DinariPA. Thermal, mechanical and optical transport properties of nanocomposite materials based on triethoxysilane-terminated polyimide and TiO2 nanoparticles. RSC Adv2015; 5: 60745–60753.
33.
YuQHuiJWangP, et al.Anion-exchange-driven disassembly of a SiO2/CTAB composite mesophase: the formation of hollow mesoporous silica spheres. Inorg Chem2012; 51: 9539–9543. DOI: 10.1021/ic301371q.
34.
LeiXQiaoMTianL, et al.Tunable permittivity in high-performance hyperbranched polyimide films by adjusting backbone rigidity. The J Phys Chem C2016; 120: 2548–2561. DOI: 10.1021/acs.jpcc.5b11667.
35.
LeiXChenYQiaoM, et al.Hyperbranched polysiloxane (HBPSi)-based polyimide films with ultralow dielectric permittivity, desirable mechanical and thermal properties. J Mater Chem C2016; 4: 2134–2146. DOI: 10.1039/c5tc03391h.
36.
LiaoWHYangSYHsiaoST, et al.Effect of octa(aminophenyl) polyhedral oligomeric silsesquioxane functionalized graphene oxide on the mechanical and dielectric properties of polyimide composites. ACS Appl Mater Inter2014; 6: 15802–15812. DOI: 10.1021/am504342j.
37.
SunFYuTHuC, et al.Influence of functionalized graphene by grafted phosphorus containing flame retardant on the flammability of carbon fiber/epoxy resin (CF/ER) composite. Composites Sci Tech2016; 136: 76–84. DOI: 10.1016/j.compscitech.2016.10.002.
38.
YangHYeLGongJ, et al.Simultaneously improving the mechanical properties and flame retardancy of polypropylene using functionalized carbon nanotubes by covalently wrapping flame retardants followed by linking polypropylene. Mater Chem Front2017; 1: 716–726. DOI: 10.1039/c6qm00172f.
39.
YuanGYangBChenY, et al.Synthesis of a novel multi-structure synergistic POSS-GO-DOPO ternary graft flame retardant and its application in polypropylene. Comp Part A Appl Sci Manuf2019; 117: 345–356. DOI: 10.1016/j.compositesa.2018.12.006.
40.
WangXDaiYWangW, et al.Fluorographene with high fluorine/carbon ratio: a nanofiller for preparing low-κ polyimide hybrid films. ACS Appl Mater Inter2014; 6: 16182–16188. DOI: 10.1021/am5042516.
41.
ChenMQiMYaoL, et al.Effect of surface charged SiO 2 nanoparticles on the microstructure and properties of polyimide/SiO 2 nanocomposite films. Surf Coat Tech2017; 320: 59–64. DOI: 10.1016/j.surfcoat.2017.01.120.
42.
DeviRRMajiTK. Interfacial effect of surface modified TiO2 and SiO2 nanoparticles reinforcement in the properties of wood polymer clay nanocomposites. J Taiwan Inst Chem Eng2013; 44: 505–514. DOI: 10.1016/j.jtice.2012.11.018.
43.
ChenZLiuSYanS, et al.Overall improvement in dielectric and mechanical properties of porous graphene fluoroxide/polyimide nanocomposite films via bubble-stretching approach. Mater Des2017; 117: 150–156. DOI: 10.1016/j.matdes.2016.12.082.
44.
AureliMPorfiriMGuptaN. Effect of polydispersivity and porosity on the elastic properties of hollow particle filled composites. Mech Mater2010; 42: 726–739. DOI: 10.1016/j.mechmat.2010.05.002.
45.
XieXYangCQiXd, et al.Constructing polymeric interlayer with dual effects toward high dielectric constant and low dielectric loss. Chem Eng J2019; 366: 378–389. DOI: 10.1016/j.cej.2019.02.106.
46.
WangWCVoraRHKangET, et al.Nanoporous ultra-low-κ films prepared from fluorinated polyimide with grafted poly(acrylic acid) side Chains. Adv Mater2004; 16: 54–57. DOI: 10.1002/adma.200305185.
47.
MaSWangYLiuC, et al.Preparation and characterization of nanoporous polyimide membrane by the template method as low-k dielectric material. Polym Adv Tech2016; 27: 414–418. DOI: 10.1002/pat.3686.
