Results of tensile and compression tests on a short-glass-fiber-reinforced thermotropic liquid crystalline polymer are presented. The effect of strain rate on the compression stress-strain characteristics has been investigated over a wide range of strain rates e between 10-4 and 350 s'l. The low-strain-rate tests were conducted using a screw-driven universal tensile tester, while the high-strain-rate tests were carried out using the split Hopkinson pressure bar technique. The compression modulus was shown to vary with log10 (ė) in a bilinear manner. The compression modulus is insensitive to strain rate in the low-strain-rate regime (ė = 10-4 - 10-2 s-'), but it increases more rapidly with ė at higher ė. The compression strength changes linearly with log10 (ė) over the entire strain- rate range. The fracture surfaces were examined by scanning electron microscopy.
References
1.
1. Donald, A. M. and A. H. Windle. 1992. Liquid Crystalline Polymers. Cambridge University Press.
2.
2. Chung, T. S.1988. "Production of Ultrahigh-Modulus Liquid-Crystal Polymer Rods,"J. Polym. Sci., Polym. Phys. Ed., 26:1549-1552.
3.
3. Choy, C. L., W. P. Leung and A. F. Lee. 1992. "Ultrasonic Measurements of the Elastic Moduli of Liquid Crystalline Polymers,"Polymer, 33:1788-1791.
4.
4. Ophir, Z. and Y. Ide. 1983. "Injection Molding of Thermotropic Liquid Crystal Polymers,"Polym. Eng. Sci., 23:792-796.
5.
5. Weng, T., A. Hiltner and E. Baer. 1986. "Hierarchical Structure in a Thermotropic Liquid-Crystalline Copolyester,"J. Mater. Sci., 21:744-750.
6.
6. Boldizar, A.1988"The Effects of Injection Rate and Mould Design on the Mechanical Properties of an Injection Molded Liquid Crystalline Copolyester,"Plastics Rubber Proc. Appl., 10:73-78.
7.
7. Thapar, H. and M. J. Bevis. 1989. "Processing, Property and Morphology of an Injection Moulded Liquid Crystal Thermoplastic Polymer,"Plastics Rubber Proc. Appl., 12:39-52.
8.
8. Sweeney, J., B. Brew, R. A. Duckett and I. M. Ward. 1992. "Mechanical Anisotropy and Inhomogeneity of an Aromatic Liquid Crystalline Polyester,"Polymer, 33:4901-4907.
9.
9. Zulle, B., A. Demarmels, C. Plimmer and H. H. Kausch. 1991. "Processing, Morphology and Properties of Filled and Unfilled LCP," in Proceedings of the 8th International Conference on Deformation Yield and Fracture of Polymers. London: Plastic and Rubbers Institute, pp. 87/1-87/4.
10.
10. Schledjewski, R. and K. Friedrich. 1992. "Tensile Properties of Filled Liquid-Crystal Polymer Systems,"J. Mater. Sci. Lett., 11:840-842.
11.
11. Li, R. K. Y., S. N. Lu, C. L. Choy and C. McCall. 1993. "Structure-Mechanical Property Relationship in Thermotropic Liquid Crystalline Polymer and Its Short Fiber Composite' in Proceedings of the International Conference on Advanced Composites Fabrication, Processing, Properties, Performance, Design and Applications. TMS, pp. 855-860.
12.
12. Chung, T. S. and P. E. McMahon. 1986. "Thermotropic Polyester Amide-Carbon Fiber Composites,"J. Appl. Polym. Sci., 31:965-977.
13.
13. Voss, H. and K. Friedrich. 1986. "Influence of Short-Fibre Reinforcement on the Fracture Behavior of a Bulk Liquid Crystal Polymer,"J. Mater. Sci., 21:2889-2900.
14.
14. Wu, J. S., K. Friedrich and M. Grosso. 1989. "Impact Behavior of Short Fibre/Liquid Crystal Polymer Composites,"Composites, 20:223-233.
15.
15. Chivers, R. A. and D. R. Moore. 1991. "The Influence of Flow Path Length on the Stiffness and Toughness of Some Engineering Thermoplastics,"Polymer, 32:2190-2198.
16.
16. Harding, J.1993. "Effect of Strain Rate and Specimen Geometry on the Compressive Strength of Woven Glass-Reinforced Epoxy Laminates;"Composites, 24:323-332.
17.
17. Kolsky, H.1949. "An Investigation of the Mechanical Properties of Materials at Very High Rates of Loading,"Proc. Phys. Soc., Section B, 62:676-700.
18.
18. Davies, E. D. H. and S. C. Hunter. 1963. "The Dynamic Compression Testing of Solids by the Method of the Split Hopkinson Pressure Bar,"J. Mech. Phys. Solids, 11:155-179.
19.
19. Griffiths, L. J. and D. J. Martin. 1974. "A Study of the Dynamic Behaviour of a Carbon-Fiber Composite Using the Split Hopkinson Pressure Bar,"J. Phys. D: Appl. Phys., 7:2329-2341.
20.
20. Bai, Y. and J. Harding. 1984. "Fracture Initiation in Glass-Reinforced Plastics under Impact Compression" in Proceedings of International Conference on Structural Impact and Crash-worthiness. London: Imperial College, 2:482-493.
21.
21. Walley, S. M., J. E. Field, P. H. Pope and N. A. Safford. 1989. "A Study of the Rapid Deformation Behaviour of a Range of Polymers,"Phil. Trans. R. Soc. Lond., A328:1-33.
22.
22. Harding, J. and L. M. Welsh. 1983. "A Tensile Testing Technique for Fiber-Reinforced Composites at Impact Rates of Strain,"J. Mater. Sci., 18:1810-1826.
23.
23. Harding, J., Y. Li, K. Saka and M. E. C. Taylor. 1989. "Characterisation of the Impact Strength of Woven Carbon/Epoxy Laminates," in Proceedings of the 4th Oxford Conference on Mechanical Properties of Materials at High Rates of Strain. Institute of Physics, pp. 403-410.
24.
24. Saka, K. and J. Harding. 1990. "A Simple Laminate Theory Approach to the Prediction of the Tensile Impact Strength of Woven Hybrid Composites;"Composites, 21:439-447.
25.
25. Li, R. K. Y., Y. M. Wong and J. Harding. 1992. "Strain Rate Effect on the Elastic Properties of PPS (Polyphenylene Sulfide) Composites;" in Proceedings of the 2nd International Symposium on Composite Materials and Structures. Peking University Press, pp. 25-30.
26.
26. Chiem, C. Y. and Z. G. Liu. 1988. "The Relationship between Tensile Strength and Shear Strength in Composite Materials Subjected to High Strain Rates;"J. of Engineering Materials and Technology, 110:191-194.
27.
27. Sawyer, L. C. and M. Jaffe. 1986. "The Structure of Thermotropic Copolyesters,"J. Mater. Sci., 21:1897-1913.
