The influence of styrene content and thickness of the samples on the UV curing of vinyl ester/styrene resins (VERs) is investigated by DSC and the combination of TGA and FTIR (TGA—FTIR). The glass transition temperatures (Tg) of the network polymers after curing are found to be lower for the VERs with higher styrene content. The released heat during UV curing further increases the Tg, with this increase being proportional to the volume of the resins. Within the range of thickness investigated (up to 30 mm) the relative amount of emissions of styrene, VE, and CO2 are found to be similar at the top and at the bottom of the samples. Similar results are obtained from the TGA analysis, indicating that the VERs are fully or almost fully cured all along the cross section. A good correlation is found between the analysis of the thermal properties by DSC and the results obtained by the TGA—FTIR system.
Kim, D.S. and Seo, W.H. (2004). Ultraviolet-curing Behavior and Mechanical Properties of a Polyester Acrylate Resin, J. Appl. Polym. Sci., 92: 3921—3928.
2.
Zhang, J.Y., Windall, G. and Boyd, I.W. (2002). UV Curing of Optical Fiber Coatings using Excimer Lamps, Appl. Surf. Sci., 186: 568—572.
3.
Decker, C., Zahouily, K., Keller, L., Benfarhi, S., Bendaikha, T. and Baron, J. (2002). Ultrafast Synthesis of Bentonite-acrylate Nanocomposite Materials by UV-radiation Curing, J. Mat. Sci., 37: 4831—4838.
4.
Decker, C. (1998). The Kinetics of Vinyl Acrylate Photopolymerization , Ibid.45: 133.
5.
Dean, K., Cook, W.D., Zipper, M.D. and Burchill, P. (2000). Curing Behaviour of IPNs Formed from Model VERs and Epoxy Systems. I: Amine Cured Epoxy, Polymer, 42(4): 1345—1359.
6.
Ganem, M., Montaigne, B., Bellinger, V. and Verdu, J. (1993). Properties of a Vinyl Ester Resin Modified with a Liquid Polymer, J. Macromol. Sci., Pure Appl. Chem., A30(11): 829.
7.
Brill, R.P. and Palmese, G.R. (2000). An Investigation of Vinylester-styrene Bulk Copolymerization Cure Kinetics using Fourier Transform Infrared Spectroscopy, J. Appl. Polym. Sci., 76: 1572—1582.
8.
Ziaee, S. and Palmese, G.R. (1999). Effects of Temperature on Cure Kinetics and Mechanical Properties of Vinyl-ester Resins, J. Polym. Sci.: Part B: Polym. Phys., 37: 725—744.
9.
Scott, T.F., Cook, W.D. and Forsythe, J.S. (2002). Kinetics and Network Structure of Thermally Cured Vinyl Ester Resins, Europ. Polym. J., 38: 705—716.
10.
Aronhime, M.T. and Gillham, J.K. (1986). Time-temperature-transformation (TTT) Cure Diagram of Thermosetting Polymeric Systems, Adv. Polym. Sci., 78: 83—113.
11.
Rozenberg, B.A. (1985). Kinetics, Thermodynamics and Mechanism of Reactions of Epoxy Oligomers with Amines, Adv. Polym. Sci., 75: 113—165.
12.
Suzuki, M. and Wilkie, C.A. (1995). Copolymerization Kinetics of Styrene/Vinyl-ester Systems: Low Temperature Reactions, Polym. Degr. Stab., 47: 217—221.
13.
Wilkie, C.A. (1999). TGA/FTIR Studies on the Thermal Degradation of Some Polymeric Sulfonic and Phosphonic Acids and their Sodium Salts, Polym. Degr. Stab., 66: 301—306.
14.
Yang, H. and Lee, J. (2001). Comparison of Unsaturated Polyester and Vinylester Resins in Low Temperature Polymerization, Polym. Comp., 22(5): 668—679.
15.
Lam, P.W.K. , Plaumann, H.P. and Tran, T. (1990). An Improved Kinetic Model for the Autocatalytic Curing of Styrene-based Thermoset Resins, J. Appl. Polym. Sci., 41(11—12): 3043—3057.
16.
Dow Chemical (1994). Fabrication Tips, DERAKANE Epoxy and Vinyl Ester Resins.
17.
Shan, L., Robertson, C.G., Verghese, K.N.E., Burts, E., Riffle, J.S., Ward, T.C. and Reifsnider, K.L. (2001). Influence of Vinyl Ester/Styrene Network Structure on Thermal and Mechanical behavior, J. Appl. Polym. Sci.,80(7): 917—927.
18.
Venditti, R.A. , Gillham, J.K., Chin, E. and Houlihan, F.M. (1994). Polymeric Materials Science and Engineering, In: Proceedings of the ACS Division of Polymeric Materials Science and Engineering, Edited by Pmse, Elsevier (ISBN: 0-8412-2844-2), Vol. 71, p. 737.
19.
Cardona, F., Rogers, D., Davey, S. and Van Erp, G. (2007). Investigation by TGA-FTIR of the Effect of Styrene Content on the Ultimate Curing of Vinylester Resins, J. Composite Mat., 41(2): 137—152.
20.
Wisanrakkit, G. and Gillham, J.K. (1990). Continuous Heating Transformation (CHT) Cure Diagram of An Aromatic Amine/Epoxy System at Constant Heating Rates, J. Appl. Polym. Sci., 41(11—12): 2885—2929.
21.
Samaras, Z.I. and Partridge, I.K. (2003). Effects of Styrene Evaporation on the Cure Kinetics Behaviour of a Vinylester Resin System Suitable for Composite Pultrusion, Polymers and PolymerComposites , 11(8): 623—632.
22.
Wisanrakkit, G., Gillham, J.K. and Enns, J.B. (1990). The Glass Transition Temperature (tg) as a Parameter for Monitoring the Cure of an Amine/Epoxy System at Constant Heating Rates, J. Appl. Polym. Sci., 41(7—8): 1895—1912.
23.
Russell, P.B. and Giuseppe, R.P. (2000). Cure Behavior of DGEBA Vinyl Ester-Styrene Resins Near Silane-Treated Interfaces, J. Appl. Polym. Sci., 76: 1572—1582.
24.
Cullis, C.F. and Hirschler, M.M. (1981). The Combustion of Organic Polymers, Clarendon Press, Oxford, p. 117.
25.
Suzuki, M. and Wilkie, C.A. (1995). The Thermal Degradation of Acrylonitrile-butadienestyrene Terpolymer as Studied by TGA/FTIR, Polym. Degrad. Stab., 47: 217—221.
