The management of dredged sediments poses serious environmental and economic problems because of their geochemical properties and in particular their pollutant content. In this research, marine sediments from Tunisian harbors were collected to study their beneficial reuse as construction materials using an eco-friendly polymer binder. Experimental investigations include the determination of physicochemical, mineralogical, and environmental parameters of sediments from the Sidi Mansour and Sidi Youssef areas in Tunisia. Prismatic mortar samples (4 × 4 × 16 cm) were prepared at laboratory scale using normalized sand and epoxy resin. Then their composition was modified by including a sediment fraction in the substitution of sand at rates ranging from 10 to 50% in dry mass. After a 7-day curing period, mortar samples were submitted to mechanical, physicochemical, and environmental analyses. Mortar samples including sediment fractions displayed lower strength than sand mortar used as control. This result is explained by the increase of porosity values in the mortar samples when sediment samples were incorporated. A positive relationship between porosity and compressive strength values was evidenced, suggesting that the compactness of granular skeleton could play an important role in the preparation of materials. From an environmental point of view, the mortar samples containing sediment fractions showed relatively low leaching levels, which confirms their suitability for the manufacturing of construction materials.
Afnor (2000a) French standards association. Part 1: Grain size distribution — laser diffraction method, NF ISO 13320-1: 2000.
2.
Afnor (2000b) French standards association. Rocks - Tests for determining the physical properties of rocks - Part 3: determination of porosity, NF P 94-410-3: 2000.
3.
Afnor (2002) French standards association. Leaching – compliance test for leaching of granular waste materials and sludges - Part 2: One stage batch test at a liquid to solid ratio of 10l/kg for materials with particle size below 4 mm (without or with size reduction), NF EN 12457: 2002.
4.
Afnor (2003) French standards association. Charaterization of waste - Microwave assisted digested with a mixture of hydrofluoric (HF); nitric (HNO3) and hydrochloric (HCl), NF EN 13656: 2003.
5.
Afnor (2005a) French standards association. Methods of testing cement - Determination of strength, NF EN 196-1: 2005.
6.
Afnor (2005b) French standards association. Water quality - Determination of selected elements by inductively coupled plasma optical emission spectrometry (ICP-OES) - Water quality, NF ISO 11885: 2005.
7.
Afnor (2006) French standards association. Fine ceramics (advanced ceramics, advanced technical ceramics), determination of specific area of ceramic powders by gas absorption using the BET method, NF ISO 18757: 2006.
8.
Afnor (2008) French standards association. Tests for determining the mechanical and physical properties of aggregates - Part 7: Determination of the absolute density of the filler - Pyknometer method, NFEN 1097-7: 2008.
9.
Afnor (2016) French standards association. Ceramic tile - Part 13: Determina-tion of chemical resistance, NF ISO 10545-13: 2016.
10.
AllalBLAmmariMFrarI, et al. (2014) Stabilization of contaminated canal sediments. European Journal of Environmental and Civil Engineering15: 293–302.
11.
AriffinNFHussinMWMohd SamAR, et al. (2015) Strength properties and molecular composition of epoxy-modified mortars. Construction and Building Materials94: 315–322.
Bel Hadj AliILafhajZBouassidaM, et al. (2014) Characterization of Tunisian marine sediments in Rades and Gabes harbors. International Journal of Sediment Research29: 391–401.
14.
BenslafaFKAKerdalDAmeurM, et al. (2015) Durability of mortars made with dredged sediments. Procedia Engineering118: 240–250.
15.
BenzerzourMAmarMAbriakN-E (2017) New experimental approach of the reuse of dredged sediments in a cement matrix by physical and heat treatment. Construction and Building Materials140: 432–444.
16.
BulutHAŞahinR (2017) A study on mechanical properties of polymer concrete containing electronic plastic waste. Composite Structures178: 50–62.
17.
CJB and EAM (2006) Etude d’identification des sites de rejet des matériaux de dragage dans les ports de commerce Tunisiens.
18.
CJB and EAM (2007) Etude d’impact sur l’environnement du dragage du complexe portuaire La Goulette-Radès, OMMP Office de la Marine Marchande et des ports.
DoubaAEmirogluMKandilUF, et al. (2019) Very ductile polymer concrete using carbon nanotubes. Construction and Building Materials196: 468–477.
21.
DuJBuYGuoS, et al. (2017) Effects of epoxy resin on ground-granulated blast furnace slag stabilized marine sediments. RSC Advances7: 36460–36472.
22.
DuboisVAbriakNEZentarR, et al. (2009) The use of marine sediments as a pavement base material. Waste Management29: 774–782.
23.
EnnahalIMaherziWMamindy-PajanyY, et al. (2019) Eco-friendly polymers mortar for floor covering based on dredged sediments of the north of France. Journal of Material Cycles and Waste Management21: 861–871.
24.
FarzadniaNBahmaniSHAsadiA, et al. (2018) Mechanical and microstructural properties of cement pastes with rice husk ash coated with carbon nanofibers using a natural polymer binder. Construction and Building Materials175: 691–704.
25.
FerdousWManaloAAravinthanT, et al. (2016) Properties of epoxy polymer concrete matrix: Effect of resin-to-filler ratio and determination of optimal mix for composite railway sleepers. Construction and Building Materials124: 287–300.
26.
FernandesEMCorreloVMChagasJAM, et al. (2011) Properties of new cork–polymer composites: Advantages and drawbacks as compared with commercially available fibreboard materials. Composite Structures93: 3120-3129.
27.
GastaldiniALGda SilvaMPZamberlanFB, et al. (2014) Total shrinkage, chloride penetration, and compressive strength of concretes that contain clear-colored rice husk ash. Construction and Building Materials54: 369–377.
28.
Geode (1996) Métaux et polychlorobiphényles (PCB) dans les sédiments dragués dans les ports français: évolution 1986-1993; Concertation et sa synthèse. Projet d’amélioration des accès maritimes du port de Rouen. Vallée de Seine.
29.
GhorbelEHaidarM (2016) Durability to chemical attack by acids of epoxy microconcretes by comparison to cementitious ones. Advances in Civil Engineering2016: 1–15.
JOCE (2014) Council Decision of 12 December 2014 establishing criteria and procedures for the acceptance of inert non-hazardous waste subject to the prior acceptance process under Article III and Annexe II to Directive 1999/31/EC. Available at: https://www.legifrance.gouv.fr/affichTexte.do?cidTexte=JORFTEXT000029893828&categori (accessed 12 December 2014).
33.
KongX-MWuC-CZhangY-R, et al. (2013) Polymer-modified mortar with a gradient polymer distribution: Preparation, permeability, and mechanical behaviour. Construction and Building Materials38: 195–203.
34.
Mamindy-PajanyYHurelCGéretF, et al. (2013) Arsenic in marine sediments from French Mediterranean ports: Geochemical partitioning, bioavailability and ecotoxicology. Chemosphere90: 2730–2736.
35.
MeimaJAComansRN (1999) The leaching of trace elements from municipal solid waste incinerator bottom ash at different stages of weathering. Applied Geochemistry14: 159–171.
36.
MissaouiASaidILafhajZ, et al. (2016) Influence of enhancing electrolytes on the removal efficiency of heavy metals from Gabes marine sediments (Tunisia). Marine Pollution Bulletin113: 44–54.
37.
NóvoaPJROFerreiraMCSFerreiraAJM, et al. (2004) Mechanical characterization of lightweight polymer mortar modified with cork granulates. Composites Science and Technology64: 2197–2205.
38.
OSPAR Convention (1992) Convention for the protection of the marine environment of the North-East Atlantic. Available at: https://www.ospar.org/convention (accessed 10 March 2020).
39.
ReisJML dos (2005) Mechanical characterization of fiber reinforced Polymer Concrete. Materials Research8: 357–360.
40.
RozièreESamaraMLoukiliA, et al. (2015) Valorisation of sediments in self-consolidating concrete: Mix-design and microstructure. Construction and Building Materials81: 1–10.
41.
SaidIMissaouiALafhajZ (2015) Reuse of Tunisian marine sediments in paving blocks: Factory scale experiment. Journal of Cleaner Production102: 66–77.
42.
SchaeferCEKupwade-PatilKOrtegaM, et al. (2018) Irradiated recycled plastic as a concrete additive for improved chemo-mechanical properties and lower carbon footprint. Waste Management71: 426–439.
43.
ScribotCMaherziWBenzerzourM, et al. (2018) A laboratory-scale experimental investigation on the reuse of a modified red mud in ceramic materials production. Construction and Building Materials163: 21–31.
44.
SosoiGBarbutaMSerbanoiuAA, et al. (2018) Wastes as aggregate substitution in polymer concrete. Procedia Manufacturing22: 347–351.
45.
SungC-YKimY-I (2012) Void ratio and durability properties of porous polymer concrete using recycled aggregate with binder contents for permeability pavement. Journal of Applied Polymer Science126: 338–348.
46.
XinHLiuYMosallamAS, et al. (2017) Evaluation on material behaviors of pultruded glass fiber reinforced polymer (GFRP) laminates. Composite Structures182: 283–300.
47.
ZellegMSaidIHamdiE, et al. (2018) Experimental testing for Zarzis port sediments (Tunisia) in road materials. Geotechnical Research5: 13–21.
