The effect of cure cycle on the quality of angle-bend thermoset composite parts is presented. A 2-D finite difference scheme was used to model the processing of arbitrary shaped composite laminates. This model includes heat transfer, viscosity, rate of cure, and resin flow submodels. Experiments were done to investigate the effect of different curing cycles on thickness variation and fiber volume fraction distribution. Results from both simulation and experiment were compared.
Get full access to this article
View all access options for this article.
References
1.
1. C. C. Hiel, M. Smith, and D. Chappell, "A curved beam test specimen for determining the interlaminar tensile strength of laminated composites,"J. Composite Materials, vol. 25, pp. 854-868, 1991.
2.
2. R. L. Ramkumar, G. Grimes, D. Adams, and E. Dusablon, Effects of Materials and Process Defects on the Compression Properties ofAdvanced Composites. Final Technical Report, Contract Nos. N00019-80-C-0490 and N00019-80-C-0484, Naval Air Systems Command, 1982.
3.
3. J. E. McCarty and M. M. Ratwani, Damage Tolerance of Composites, Interim Report No. 1, Contract No. F33615-82-C-3213, Air Force Wright-Aeronautical Laboratory, Wright-Patterson Air Force Base, OH, 1983.
4.
4. R. H. Martin, "Delamination failure in a unidirectional curved composite laminate,"Composite Materials: Testing and Design, ASTM STP 1120, pp. 365-383, 1992.
5.
5. W. C. Jackson and R. Martin, "An interlaminar tensile strength specimen,"Composite Materials: Testing and Design, ASTMSTP 1206, pp. 333-354, 1993.
6.
6. R. H. Martin and W. C. Jackson, "Damage prediction in cross-plied curved composite laminates,"Composite Materials: Fatigue and Fracture, ASTM STP 1156, pp. 105-126, 1993.
7.
7. W. C. Jackson, "Through-the-thickness test strength of textile composites,"Composite Materials: Testing and Design, ASTMSTP 1274, pp. 218-238, 1996.
8.
8. K. N. Shivakumar, H. G. Allen, and V. S. Avva, "Interlaminar tension strength of graphite/epoxy composite laminates,"AIAA Journal, vol. 32, pp. 1478-1484, 1994.
9.
9. V. S. Avva, H. G. Allen, and K. N. Shivakumar, "Through-the-thickness tension strength of 3-D braided composites,"J. Composite Materials, vol. 30, pp. 51-68, 1996.
10.
10. A. O. Kays, Exploratory Development on Processing Science of Thick Section Composites. Technical Report, AFWAL-TR-85-4090, Air Force Wright Aeronautical Laboratories, Wright Patterson AFB, OH, 1985.
11.
11. T. E. Twardowski, S. E. Lin, and P. H. Geil, "Curing in thick composite laminates: Experiment and simulation,"J. Composite Materials, vol. 27, pp. 216-250, 1993.
12.
12. T. A. Bogetti and J. W. Gillespie, "Process-induced stress and deformation in thick section thermosetting composite laminates," in 21st SAMPE Technical Conference, New Jersey, Sept. 1989.
13.
13. M. Hojjati and S. V. Hoa, "Curing simulation of thick thermosetting composites,"Composites Manufacturing, vol. 5, no. 3, pp. 159-171, 1994.
14.
14. A. Johnston, P. Hubert, G. Fernlund, R. Vaziri, and A. Poursartip, "Process modeling of composite structures employing a virtual autoclave concept,"Science and Engineering of Composite Materials, vol. 5, pp. 235-252, 1996.
15.
15. S. W. Tsai and H. T. Hahn. Introduction to Composite Materials. Technomic Publishing Co., Inc., 1980.
16.
16. G. S. Springer and S. W. Tsai, "Thermal conductivity's of unidirectional materials,"J. Composite Materials, vol. 1, pp. 166-173, 1967.
17.
17. R. Dave, J. L. Kardos, and M. P. Dudukovic, "A model for resin flow during composite processing: Part 1 general mathematical development,"Polymer Composites, vol. 8, pp. 29-38,1987.
18.
18. J. V. der Westhuizen and J. P. D. Plessis, "Quantification of unidirectional fiber bed permeability,"J. Composite Materials, vol. 28, pp. 619-637, 1994.
19.
19. J. V. der Westhuizen and J. P. D. Plessis, "An attempt to quantify fiber bed permeability utilizing the phase average Navier-Stokes equation,"Composites. part a, applied science and manufacturing, vol. 27, pp. 263-269, 1996.
20.
20. T. G. Gutowski, T. Morigaki, and Z. Cai, "The consolidation of laminate composites,"J. Composite Materials, vol.21, pp. 172-188, 1987.
21.
21. W. B. Young, "Resin flow analysis in the consolidation of multi-directional laminated composites,"Polymer Composites, vol. 16, no. 3, pp. 250-257, 1995.
22.
22. W. I. Lee, A. C. Loos, and G. S. Springer, "Heat of reaction, degree of cure, and viscosity of 3501-6 resin,"J. Composite Materials, vol. 16, pp. 510-520, 1982.
23.
23. J. F. Thompson, F. C. Thames, and C. W. Mastin, "Automatic numerical generation of bodyfitted curvilinear coordinate systems for field containing any number of arbitrary two-dimensional bodies,"Journal of Computational Physics, vol. 15, pp. 299-319, 1974.
24.
24. J. F. Thompson, Z. A. U. Waris, and C. W. Mastin. "Body-fitted coordinate systems for numerical solution of partial differential equations a review,"J. Computational Physics, vol. 47, pp. 1-108,1982.
25.
25. H. Z. Barakat and J. A. Clark, "On the solution of the diffusion equations by numerical methods,"J. Heat Transfer, pp. 421-427, 1966.
26.
26. M. I. Naji, Curing of Thick-Angle-Bend Thermosetting Composites. PhD thesis, Mechanical Engineering, Concordia University, Montreal, Canada, expected Sep., 1998.
