A SEM-Fractographic Study of Dynamic Crack Propagation Effects in Particulate Epoxy Systems under Impact Loading Conditions

Abstract

In this complex study an attempt was made on the one hand to analyze and understand in a systematic way the exact nature of the formation of certain characteristic energy dissipation-induced fractographic features and patterns/markings revealed by scanning electron microscopy (SEM) in particulate epoxy systems under impact (dynamic) loading conditions, and on the other hand to correlate these patterns and features with relevant crack propagation effects. For this scope a combined approach consisting of a qualitative as well as a semiquantitative analysis was employed. In the qualitative analytical approach it was shown that depending on the actual velocity and direction of crack propagation the above observed fractographic entities can be correlated to certain highly localized energy dissipative processes at front-failures as well as to local inertial molecular mass effects.

Depending on the changes in the velocity and direction of propagation, the associated effects may be controlled by two basic processes: the single crack front and the multiple crack front splitting. The first process seemed to be governed by a shear toughness-biased system, whereas the second one used a critical strain energy release rate subcracking mechanism. Under certain conditions both processes may be influenced by inertial molecular effects in promoting the formation of relative-smooth fracture surfaces.

The increased presence of particles tends to restrict an increase in the surface roughness due to energy dissipation-induced crack retardation effects. The presence of the notch tends to lower the fracture surface roughness compared to notch-free specimens and also to suppress the occurrence of certain elastic as well as viscoelastic-plastic crack delay effects observed in notch-free specimens in function of particle volume fraction.

Based on relevant kinematics-aided modeling and impact energy measurements it seems possible to explain, by a gross semi-quantitative approach, the above particles and notch effects. In this context it seems plausible that the existence of a defect-induced fracturing time spectrum of the propagating crack front, in combination with the `notch-induced shift' behavior of this spectrum, can be valuable for some approximating explanations of the above notch effects and in general the `kinematics' of the surface roughness formation.

Keywords

surface roughness fractographic patterns kinematic toughness single crack splitting multiple crack splitting fracture process time spectrum dissipative effects retardation effects defect-induced shift crack velocity viscoelastic effects.

Get full access to this article

View all access options for this article.

References

Kim, S.L. , Skobo, M.D. , Manson, J. , Herzberg, R.W. and Janiszewski , J. (1978). Tensile, Impact and Fatigue Behavior of an Amine-Cured Epoxy Resin, Polym . Eng. Sci., 18: 1093-1100.

Shioya, T. and Ishida, R. (1991). Microscopic Fracture Modes of Brittle Polymers in Dynamic Crack Propagation, In: Rossmanith, H. P. and Rosakis, A. J. (eds), Proceedings of International Seminar on Dynamic Failure of Materials: Theory, Experiments and Numerics, Vienna, Austria, 2-4 January.

Low, I.-M. and Mai, Y.-W. (1989). Rate and Temperature Effects on Crack Blunting Mechanisms in Pure and Modified Epoxies, J. Mat. Sci., 24: 1634-1644.

Masters, J. and Au, J. J. (eds). (1987). Fractography of Modern Engineering Materials: Composites and Metals, ASTM-STP 948, pp. 238-258.

Masters, J. E. and Gilbertson, L. N. (eds). (1993). Fractography of Modern Engineering Materials, Vol. 2: Composites and Metals, ASTM-STP 1203.

Roulin-Maloney, A.C. (ed.) (1989). Fractography and Failure Mechanisms of Polymers and Composites, Elsevier Science Inc., Amsterdam, Oxford, New York, Tokyo.

Electron Fractography, ASTP-STP 436.

Gilbertson, L.N. and Zipp, R. D. (eds.) (1981). Fractography and Material Science, ASTM-STP.

Fractography-Microscopic Cracking Process (1976). ASTM-STP 600.

10.

Cantwell, W.J. , Roulin-Moloney, A.C. and Kaiser, T. (1988). Fractography of Unfilled and Particulate-Filled Epoxy Resins, J. Mat. Sci., 23: 1615-1631.

11.

Kim, J.R. and Robertson, R.E. (1992). Toughening of Thermosets Polymers by Rigid Particles, J. Mat. Sci., 27: 161-174.

12.

Pearson, R.A. and Yee, A.F. (1986). Thoughening Mechanisms in Elastomer-Modified Epoxies, J. Mat. Sci., 21: 2475-2488.

13.

Gupta, V.B. , Drzal, L.T. , Adams, W.W. and Ombor, R. (1985). An Electron Microscopic Study of the Morphology of Cured Epoxy Resins, J. Mat. Sci. , 20: 3439-3452.

14.

Phillips, D.C. , Scott, J.M. and Jones, M. (1978). Crack Propagation in Amine-Cured Epoxy Resins, J. Mat. Sci., 13: 311-322.

15.

Cherry, B.M. and Thomson, K.W. (1981). The Fracture of Highly Crosslinked Polymers, Part 2: Fractography, J. Mat. Sci., 16: 1925-1934.

16.

Kinloch, A.J. , Gilbert, D. and Shaw, S.J. (1986). A Mechanism for Ductile Crack Growth in Epoxy Polymers, J. Mat. Sci., 21: 1051-1056.

17.

Vakil, U.M. and Martin, G.C. (1993). Yield and Fracture Behavior of Cross-Linked Epoxies, J. Mat. Sci., 28: 4442-4450.

18.

Yamini, S. and Jonny, R.J. (1979). Crack Propagation and Fractography of Epoxy Resins , J. Mat. Sci., 14: 1609-1618.

19.

Robertson, R.E. , Spores, M.G. , Pan, T.Y. and Mindroiu, V.E. (1989). Plasticity of Brittle Epoxy Resins During Debonding Failure, J. Mat. Sci., 24: 4106-4113.

20.

Kinloch, A.J. and Jonny, R.J. (1985). Fracture Behavior of Polymers, Elsevier Applied Science Publishers LDT, London, New York.

21.

Finn, S.R. and Springer, G.S. (1991). Composite Plates Impact Damage, Technomic Publishing Co. Inc., Lancaster, PA.

22.

Mott, N.F. (1948). Fracture of Metals: Theoretical Considerations , Engineering, 165(4275): 16-18.

23.

Rosen, B. (1964). Mechanical Aspects, In: Rosen, B. (ed.), Fracture Processes in Polymeric Solids: Theory and Phenomena, Interscience Publishers, John Wiley, New York, London, Sydney, pp. 39-106.

24.

Yoffe, E.H. (1951). Phil. Mag., 12: 739-750.

25.

Berry, J.P. (1964). General Theory of Brittle Solids, In: Rosen, B. (ed.), Fracture Processes in Polymeric Solids: Theory and Phenomena, Interscience Publishers, John Wiley, New York, London , Sydney, pp. 157-194.

26.

Bilby, B.A. , Cottrell, A.H. and Swinden, K.H. (1963). The Spread of Plastic Yield from Notch, Proc. Roy. Soc. London Ser. A., 272(1350): 300-314.

27.

Parton, V.Z. and Morozov, E.M. (1978). Elastic-Plastic Fracture Mechanics, Mir Publishers (Engl. Translation).

28.

Wolok, J. and Newman, S. (1975). Fracture Topography, In: Rosen, B. (ed.), Fracture Processes in Polymeric Solids: Phenomena and Theory, Interscience Publishers, John Wiley, New York, London, Sydney, pp. 235-290.

29.

Atkins, A.G. , Lee, C.S. and Caddell, R.M. (1975). Time-Temperature Dependent Fracture Toughness of PMMA: Part 2, 1394-1404.

30.

Theocaris, P.S. (1987). The Mesophase Concept in Composites , Henrici-Olive, G. and Olivé, S. (eds), Springer Verlag, Berlin, Heidelberg, New York , London, Paris, Tokyo.

31.

Matsuoka, S. (1992). Relaxation Phenomena in Polymers, Matsuoka, S. (ed.), Hanser Publishers, Munich, Vienna, New York, Barcelona.

32.

Kytopoulos, V.N. , Sideridis, E. and Bourkas, G.D. (2003). A Study of Some Thermomechanical and Fractural Properties of Particle-Reinforced Polymer Composites and SEM-aided Microfailure Approach of Certain Fracture Parameters, J. Reinforced Plastics and Composites, 22(17): 1547-1587.

33.

Kytopoulos, V.N. (2004). A Viscoelastic Macro-Microfracture Delay Mechanism Approach in Particulate Epoxy Composites, J. Reinforced Plastics & Composites, 23: 1325-1349.