The effect of thermal cycling on tensile and flexural properties of Cytec T650 carbon fiber/Lonza Primaset PT-30 cyanate ester pultruded composite rods proposed to be used for brush seals in gas turbine engines was evaluated. The thermal cycle consisted of 4min each of heating and cooling with 28min of hold at 315°C and 24min of hold at room temperature. Tension and three-point bend flexure tests were conducted after thermal cycling for 100, 200, 400, 600, and 800 cycles. Thermal cycling reduced the tensile strength and fracture strain almost linearly with the number of cycles while the tensile modulus remained unchanged. The flexural modulus did not change for the first 100 cycles and then decreased as much as 28% after 800 thermal cycles. Thermal cycling increased the Tg of the composite rods from 408 to 468°C. Optical and scanning electron microscopy analysis showed fiber/matrix interfacial separation and matrix shrinkage and oxidation due to thermal cycling.
Steinetz, B.M. and Hendricks, R.C. (1997). Engine Seals, Tribology for Aerospace Applications, In: Zaretsky, E. V. (ed.), pp. 595-682, Society of Tribologists and Lubrication Engineers , Park Ridge, IL.
2.
Hendricks, R.C., Griffin, T.A., Kline, T.R., Csavina, K.R., Pancholi, A. and Sood, D. (1994). Relative Performance Comparison Between Baseline Labyrinth and Dual-brush Compressor Discharge Seals in a t-700 Engine Test , 39th International Gas Turbine and Aeroengine Congress and Exposition sponsored by the American Society of Mechanical Engineers , The Hague, Netherlands.
3.
Trutnovsky, K. (1977). Contactless Seals, Foundations and Applications of Flows Through Slots and Labyrinths, NASA TT F17352.
4.
Holloway, G., Mehta, J., Rosado, L., Doak, D., Hubley, C., Askew, J. and Krawiecki, S. (2006). Innovative Rotating Intershaft Brush Seal for Sealing Between Rotating Shafts, Part I-Mechanical Design of the Rotating Brush Seal. AIAA-2006-4751, 42nd AIAA/ASME/SAE/ASEE Joint Propulsion Conference and Exhibit, Sacramento, California.
5.
Abali, F., Shivakumar, K.N., Hamidi, N. and Sadler, R. (2003). An RTM Densification Method of Manufacturing Carbon-carbon Composites using Primaset PT-30 Resin, Carbon, 41(5): 893-901.
6.
Hemerton, I. (1994). Chemistry and Technology of Cyanate Ester Resins , Blackie Academic & Professional, London, UK.
7.
Shivakumar, K., Chen, H. and Holloway, G. (2007). Durability of Carbon/Cyanate Ester Pultruded Composites in Gas Turbine Environment, 16th International Conference on Composite Materials, Kyoto, Japan.
8.
Hancox, N.L. (1998). Thermal Effects on Polymer Matrix Composites: Part 1, Thermal Cycling, Materials and Design, 19(3): 85-91.
9.
Shimokawa, T. , Katon, H., Hamaguchi, Y., Sanbongi, S. and Mizuno, H. (2006). Effect of Thermal Cycling on Microcracking and Strength Degradation of High-temperature Polymer Composite Materials for use in Next-generation SST Structures, Journal of Composite Materials, 36(7): 885-895.
10.
Lee, S. , Nam, J., Ahn, K., Chung, K. and Seferis, J. (2001). Thermo-oxidative Stability of High Performance Composites under Thermal Cycling Conditions, Journal of Composite Materials, 35(5): 433-454.
11.
Lafarie-Frenot, M.C. and Rouquie, S. (2004). Influence of Oxidative Environments on Damage in C/Epoxy Laminates Subjected to Thermal Cycling, Composites Science and Technology, 64(10-11): 1725-1735.
12.
Chung, K., Seferis, J.C. and Nam, J.D. (2000). Investigation of Thermal Degradation Behavior of Polymeric Composites: Prediction of Thermal Cycling Effect From Isothermal Data, Composites: Part A, 31(9): 945-957.
13.
Lafarie-Frenot, M.C., Rouquie, S., Ho, N.Q. and Bellenger , V. (2006). Comparison of Damage Development in C/Epoxy Laminates During Isothermal Ageing or Thermal Cycling, Composites: Part A, 37(4): 662-671.
14.
Sinmazcelik, T. and Arici, A.A. (2006). Thermal Cycles Effects on Interlaminar Shear Strength (ILSS) and Impact Behaviour of Carbon/PEI Composites , Journal of Materials Science, 41(4): 1233-1241.
15.
Cao, J. and Chen, L. (2005). Effect of Thermal Cycling on Carbon Fiber-Reinforced PPS Composites, Polymer Composites , 26(5): 713-716.
16.
Dutta, P.K. , Kalafut, J. and Lord, H.W. (1988). Influence of Low Temperature Thermal Cycling on Tensile Strength of Fiber Composites, American Society of Mechanical Engineers, Pressure Vessels and Piping Division (Publication) PVP, 146: 141-147.
17.
Kern, K.T., Long, E.R., Long, S. and Harries, W.L. (1990). Effects of Electron Radiation and Thermal Cycling on Sized and Unsized Carbon Fiber-Polyetherimide Composites, Polymer Preprints, AXS, 31(1): 611-612.
18.
Hillermeier, R.W. and Seferis, J.C. (2000). Environmental Effects on Thermaplastic and Elastomer Toughened Cyanate Ester Composite Systems, Journal of Applied Polymer Science, 77(3): 556-567.
19.
Chung, K. and Seferis, J.C. (2001). Evaluation of Thermal Degradation on Carbon Fiber/Cyanate Ester Composites, Polymer Degradation and Stability, 71(3): 425-434.
20.
Parvatareddy, H., Wang, J.Z., Dillard, D.A. and Ward, T.C. (1995). Environmental Aging to High-performance Polymeric Composites: Effects on Durability, Composites Science and Technology, 53(4): 399-409.
21.
Lee, B.L. and Holl, M.W. (1996). Effects of Moisture and Thermal Cycling on In-plane Shear Properties of Graphite Fibre-reinforced Cyanate Ester Resin Composites, Composites: Part A, 27(11): 1015-1022.
