Impact of Concrete Placing Method on Air Content,Air-Void System Parameters,and Freeze-Thaw Durability

Abstract

Approximately 76 m³ (100 yd³) of ready-mixed, air-entrained concrete were placed in a parking lot and driveway at the Schwing America Manufacturing facility in White Bear, Minnesota, on June 21, 1994. This concrete was placed by means of a pump, crane and bucket, and truck-mounted conveyor, and came directly from the chute of ready-mix trucks. Pump configurations were used that allowed unrestricted free-fall of the concrete; a kink in the rubber hose at the end of the line created a slight back pressure and slowed the descent of the concrete. After placement, the concrete was consolidated by an immersion vibrator in some locations and struck off with no further consolidation in other locations. Air content of the fresh concrete was measured by ASTM C231 pressure meters at the truck chutes and at the point of placement. Air content and air-void system parameters of the hardened concrete were determined in accordance with ASTM C457. Actual freeze-thaw performance was evaluated by ASTM C666 for concrete sampled from the truck chute and sampled from the pavement after placement by the various methods. Twenty-four tests of the air content of concrete from six successive truckloads of concrete showed that the variation in truck-to-truck air content was frequently greater than the within-truck variation because of different methods of handling the concrete. Tests of the fresh concrete after pumping, conveying, chuting, and free-fall from the concrete bucket showed reduced air content. From analysis of the hardened concrete, it was observed that the air bubbles remaining in the pumped concrete were smaller than in the concrete as delivered. The air-void spacing factor was not significantly altered by pumping. In ASTM C666 freezing and thawing tests, the specimen experiencing the greatest loss of air content as a result of pumping was determined to have the lowest total air content of all specimens tested (before vibration), yet had the highest durability of all specimens tested.

Get full access to this article

View all access options for this article.

References

Hover

K. C.

The Influence of Handling on Air-Entrained Concrete. American Concrete Pumping Association, Galena, Ohio, 1993.

Hover

K. C.

Some Recent Problems with Air-Entrained Concrete. Cement, Concrete, and Aggregates, ASTM, Vol. 11, No. 1, Summer, 1989, pp. 67–72.

Yingling

, Mullings

G. M.

, and Gaynor

R. D.

. Loss of Air Content in Pumped Concrete, Concrete International, Oct. 1992, Vol. 14, No. 10, pp. 57–61.

Elkey

, Janssen

, and Hover

. Concrete Pumping Effects on Entrained Air Voids. Final Report, Research Project T9233 Task 21, for the Washington State Transportation Commission, Washington State Transportation Center, University of Washington, Seattle, June 1994, 97 pp.

Schlecht

How to Make the Concrete Pump an Air Entraining Machine. Putzmeister-Werk, Aichtal, Germany, Oct. 1994.

Pleau

, Pigeon

, Lamontagne

, and Aitcin

P. C.

. Influence of Pumping on the Characteristics of the Air Void System of High Performance Concrete. Presented at 74th Annual Meeting of the Transportation Research Board, Washington, D.C., January 1995.

Why Is There Air in Concrete? Part 1 of series. Concrete Construction, Jan. 1993, pp. 11–15.

Obtaining and Maintaining Air-Entrained Concrete, Part 2 of series. Concrete Construction, Feb. 1993, pp. 148–152.

Measuring Air in Concrete, Part 3 of series. Concrete Construction, April 1993, pp. 275–278.

10.

Specifying Air-Entrained Concrete, Part 4 of series. Concrete Construction, Vol. 38, No. 5, May 1993, pp. 361–367.

11.

Hover

K. C.

Air Content and Unit Weight of Hardened Concrete, Significance of Tests and Properties of Concrete and Concrete-Making Materials, ASTM, STP 169C. ( Lamond , and Kleiger , eds.) 1994, Philadelphia, pp. 296–315.

12.

Simon

M. J.

, Jenkins

R. B.

, and Hover

K. C.

. The Influence of Immersion Vibration on the Air Void System in Concrete, Durability of Concrete, SP-131 ( Holm

Jens

, ed). American Concrete Institute, Detroit, Mich., 1992, pp. 99–126.

13.

Stark

D. C.

Effect of Vibration on the Air Void System and Freeze-Thaw Durability of Concrete (RD092.01T). Portland Cement Association, Skokie, Ill., 1986.

14.

Cooke

T. H.

Concrete Pumping and Spraying, A Practical Guide. Van Nostrand Reinhold, 1990, 251 pp.