Investigating the effect of hot preforming combined with superplastic forming on thickness distribution and forming time of Ti-6Al-4V alloy using finite element analysis
Restricted accessResearch articleFirst published online May, 2025
Investigating the effect of hot preforming combined with superplastic forming on thickness distribution and forming time of Ti-6Al-4V alloy using finite element analysis
The present work focuses on the development of a new superplastic forming (SPF) that utilizes hot preforming to improve thickness distribution and decrease forming time. For this purpose, finite element analysis (FEA) was employed as an efficient tool to indicate feasibility of the new method by designing the appropriate die geometry. The experimental tests were performed to find the tensile properties of Ti-6Al-4V alloy at different temperatures and angles. Detailed FEA technique was employed to model the SPF process by a constitutive model that considers both microstructural features and geometrical instabilities. The variations of the forming time and distribution of thickness due to the variation of the forming parameters such as strain rate and friction coefficient were studied to compare the results with the results of hot preforming combined with SPF process. The obtained results from FEA showed that this new method can provide a good thickness distribution, so that the thickness variation reduced from 44% to about 21% and the forming time considerably reduced from 1100 to 610 s.
JeongHBLeeJYJinJC, et al. High-strain rate and low-temperature superplasticity of Fe-Mn-Si-Ni steel. J Alloys Comp2023; 958: 170536.
2.
PanHLiXZhangS, et al. Effect of strain rate on the microstructure evolution and superplastic deformation behavior of cold-rolled medium Mn lightweight steel. Mater Sci Eng A2023; 879: 145241.
3.
AkulaSPOjhaMRaoKL, et al. A review on superplastic forming of Ti-6Al-4V and other titanium alloys. Mater Today Commun2023; 34: 105343.
4.
NazzalMAKhraishehMKDarrasBM.Finite element modeling and optimization of superplastic forming using variable strain rate approach. J Mater Eng Perform2004; 13(6): 691–699.
5.
SheikhalishahiHRasouliMAJafari NedoushanR.Improving the prediction of part thickness in superplastic forming process of Ti–6Al–4V alloy using an appropriate constitutive equation. Iran J Sci Technol Trans Mech Eng2016; 40(1): 69–75.
6.
ChenYKibbleKHallR, et al. Numerical analysis of superplastic blow forming Ti–6Al–4V alloys. Mater Des2001; 22(8): 679–685.
7.
BabuSRDeivanayagamSAravindM.Determination of material parameters during superplastic forming of AA 5086 Alloy. Procedia Eng2014; 97: 1379–1386.
8.
MatsumotoHYoshidaKLeeSH, et al. Ti–6Al–4V alloy with an ultrafine-grained microstructure exhibiting low-temperature–high-strain-rate superplasticity. Mater Lett2013; 98: 209–212.
9.
KoYGLeeCSShinDH, et al. Low-temperature superplasticity of ultra-fine-grained Ti–6Al–4V processed by equal-channel angular pressing, Metall. Mater Trans2006; 37(2): 381–391.
10.
ZhangTLiuYSandersDG, et al. Development of fine-grain size titanium 6Al–4V alloy sheet material for low temperature superplastic forming. Mater Sci Eng A2014; 608: 265–272.
11.
LiuJTanMJAue-u-lanY, et al. Superplastic-like forming of non-superplastic AA5083 combined with mechanical pre-forming. Int J Adv Manuf Technol2011; 52(1-4): 123–129.
12.
GuoMLLiuJTanMJ, et al. Microstructure evolution of Ti-6Al-4V during superplastic-like forming. Procedia Eng2014; 81: 1090–1095.
13.
SeshacharyuluTMedeirosSCFrazierWG, et al. Hot working of commercial Ti–6Al–4V with an equiaxed α–β microstructure: materials modeling considerations. Mater Sci Eng2000; 284(1–2): 184–194.
14.
AlabortEPutmanDReedRC.Superplasticity in Ti–6Al–4V: characterisation, modelling and applications. Acta Mater2015; 95: 428–442.
15.
VelayVMatsumotoHVidalV, et al. Behavior modeling and microstructural evolutions of Ti–6Al–4V alloy under hot forming conditions. Int J Mech Sci2016; 108–109: 1–13.
16.
ComleyP.Multi-rate superplastic forming of fine grain Ti-6Al-4V titanium alloy. J Mater Eng Perform2007; 16(2): 150–154.
17.
LiuJElangovanPEvgeniaY, et al. FEM study of process parameters in a novel superplastic forming of titanium alloy Ti-6Al-4V. Mater Res Proc2024; 44: 209–217.
18.
MoslehAOMikhaylovskayaAVKotovAD, et al. Experimental, modelling and simulation of an approach for optimizing the superplastic forming of Ti-6%Al-4%V titanium alloy. J Manuf Process2019; 45: 262–272.
19.
DuttaA.Thickness-profiling of initial blank for superplastic forming of uniformly thick domes. Mater Sci Eng A2004; 371(1-2): 79–81.
20.
DeshmukhPV.Study of superplastic forming process using finite element analysis. University of Kentucky Master’s Theses, Paper 367, 2003.
21.
BalasubramanianMRamanathanKKumarVSS. Mathematical modeling and finite element analysis of superplastic forming of Ti-6Al-4V alloy in a stepped rectangular die. Procedia Eng2013; 64: 1209–1218.
22.
JiangSSLuZHeXD, et al. Superplastic forming Ti−6Al−4V titanium alloy cylinder with near uniform thickness distribution. Trans Nonferrous Met Soc China2012; 22: s472–478.
23.
LiuJGuoMLTanMJ, et al. FEM study of superplastic-like forming of Ti-6Al-4V alloy. Mater Sci Forum2014; 783–786: 607–612.
24.
LiuJTanMJAue-u-lanY, et al. Superplastic-like forming of Ti-6Al-4V alloy. Int J Adv Manuf Technol2013; 69(5-8): 1097–1104.
25.
LiuJEdbergJTanMJ, et al. Finite element modelling of superplastic-like forming using a dislocation density-based model for AA5083. Modelling Simul Mater Sci Eng2013; 21(2): 025006.
26.
LuoYLuckeySGFriedmanPA, et al. Development of an advanced superplastic forming process utilizing a mechanical pre-forming operation. Int J Mach Tools Manuf2008; 48(12-13): 1509–1518.
27.
AdamLPonthotJP.A coupled thermo-viscoplastic formulation at finite strains for the numerical simulation of superplastic forming. J Mater Process Technol2003; 139(1-3): 514–520.
