The elastic stress concentrations developed from the keyless frictionless static press-fit of a shaft into a hub are addressed. Two configurations are examined, namely (a) an infinitely long solid shaft press-fitted into a hollow hub with bore rounded edges, and (b) a shaft with filleted extremity, partially inserted into a hub. Derived from an analytical approach, a normalizing parameter is proposed that accounts for the combined effects on the stress concentrations of the fillet radius, the shaft radius, the interference, and Young’s modulus. With the aid of finite elements, various design charts are compiled that report the elastic stress concentrations within the hub versus the proposed normalizing parameter. Each curve is valid for a fixed ratio of inner to outer hub radii.
BaugherJ. W.Transmission of torque by means of press and shrink fits. ASME Trans., 1931, 53, 85–92.
4.
TrockB.Shrink fits: holding power can be increased. Iron Age, 1953, 179, 179–175.
5.
ConwayH. D.FarnhamK. A.Contac stresses between cylindrical shafts and sleeves. Int. J. Engng Sci., 1967, 5, 541–554.
6.
WhiteD. J.HumphersonJ.Finite-element analysis of stresses in shafts due to interference-fit hubs. J. Strain Analysis., 1969, 4, 105–114.
7.
BhonsleS. R.WorkC. E.Evaluation of three-dimensional stresses in shrink-fit problems by scattered-light photoelasticity. Exp. Mech., 1970, 10, 19N–28N.
8.
MatherJ.BainesB. H.Distribution of stress in axially symmetrical shrink-fit assemblies. Wear, 1972, 21, 339–360.
9.
BernasconiG.Axial-symmetric elastic strains and stresses in tight cylindrical hub–shaft couplings. Meccanica, 1972, 7, 54–55.
10.
PrasadS.DasguptaS.Axisymmetric shrink fit problems of the elastic cylinder of finite length. J. Elast., 1977, 7, 225–242.
11.
SelvageC. C.Assembly of interference fits by impact and constant force methods. MSc Thesis, MIT, 1979.
12.
GrimmT. R.ChiuA. C.Design of hubs to minimize interference stresses – a finite element study. Comput. Engng, 1988, 3, 85–91.
13.
GarnettM. D.GrimmT. R.Finite Element analysis of interference-fitted shafts subjected to bending. Comput. Engng, ASME, 1989, 2, 273–280.
14.
SchmelzF.Seherr-ThossH. C.AucktorE.Universal joints and driveshafts, 1992 (Springer, Berlin).
15.
PrasadN. S.SashikanthP.RamamurtiV.Stress distribution in interference joints. Comput. Struct.s, 1994, 51, 535–540.
16.
StrozziA.Costruzione di Macchine, 1998 (Pitagora, Bologna).
17.
ZhangY.McClainB.FangX. D.Design of interference fits via finite element method. Int. J. Mech. Sci., 2000, 42, 1835–1850.
18.
NortonR. L.Machine design: an integrated approach, 2000 (Prentice-Hall, New York).
19.
CastagnettiD.DragoniE.Optimal aspect ratio of interference fits for maximum load transfer capacity. J. Strain Anal., 2005, 40, 177–184.
20.
ÖzelA.TemizS.AydinM. D.SenS.Stress analysis of shrink-fitted joints for various fit forms via finite element method. Mater. Design, 2005, 26, 281–289.
21.
KanberB.Boundary element analysis of interference fits. Turkish J. Engng Env. Sci., 2006, 30, 323–330.
22.
KolonitsF.The influence of rounded edges on the shaft–hub contact. Periodica Polytechnica Ser. Transp. Engng, 2007, 51, 35–44.
23.
AvalloneE. A.BaumeisterT.SadeghA. M.Mark’s standard handbook for mechanical engineers, 2007 (McGraw-Hill, New York).
24.
FrancisM.HenriC.Hoa NganN.Stress concentration of shrink fit assembly using finite element method. In IASTED Asian Conference on Modelling and Simulation, Beijing, China, 8–10 October 2007, pp. 67–70.
25.
PonetchiP. P.VelaI.Stress and strain of solid shafts in interference fit couplings. Analele Universitatii, ‘Eftimie Murgu’ Resita, 2008, 15,331–338.
26.
LanoueF.VadeanA.SanschagrinB.Finite element analysis and contact modelling considerations of interference fits for fretting fatigue strength calculations. Simul. Modell. Pract. Theory, 2009, 17, 1587–1602.
27.
CroccoloD.VincenziN.A generalized theory for shaft–hub couplings. Proc. IMechE, Part C: J. Mechanical Engineering Science, 2009, 223, 2231–2239.
28.
CroccoloD.VincenziN.Stress concentration factors in compression-fit couplings. Proc. IMechE, Part C: J. Mechanical Engineering Science, 2009, 224, 1143–1152.
29.
LuoHLiuC.LiK.Contacting model considerations of interference fit for shaft–hub system. Adv. Mater. Res., 2010, 118-120, 294–298.
30.
GalinL. A.Contact problems in the theory of elasticity. 1953 (Gostekhizdat, Moscow). English translation by the Department of Mathematics, North Carolina State College, Raleigh.
31.
GoodierJ. N.LoutzenheiserC. B.Pressure peaks at the ends of plane strain rigid die contacts (elastic). J. Appl. Mech.1965, 32, 462–463.
32.
StrozziA.Static stresses in an unpressurized, rounded, rectangular, elastomeric seal. ASLE Trans., 1986, 29, 558–564.
33.
CiavarellaM.HillsD. A.MonnoG.The influence of rounded edges on indentation by a flat punch. Proc. IMechE, Part C: J. Mechanical Engineering Science, 1998, 212, 212–319.
34.
JägerJ.New analytical solutions for a flat rounded punch compared with FEM. Computational Methods in Contact Mechanics V (WIT Press, Southampton), 2001, pp. 307–316.
35.
Bijak-ZochowskiM.MarekP.TraczM.On methods of reduction and elimination of stress singularities in some elastic contact problems. Int. J. Mech. Sci., 1994, 36, 279–296.
36.
OdaJ.SakamotoJ.SanK.A method for producing a uniform contact stress distribution in composite bodies with interference. Struct. Optim., 1991, 3, 23–28.
37.
BenuzziD.DonzellaG.Prediction of the press-fit curve in the assembly of a railway axle and wheel. Proc. IMechE, Part F: J. Rail and Rapid Transit, 2004, 218, 218–51.
38.
BuciumeanuM.MirandaA. S.PinhoA. C. M.SilvaF. S.Design improvement of an automotive-formed suspension component subjected to fretting fatigue. Engng Failure Anal., 2007, 14, 810–821.
39.
CiavarellaM.BaldiniA.BarberJ. R.StrozziA.Reduced dependence on loading parameters in almost conforming contacts. Int. J. Mech. Sci., 2006, 48, 917–925.
40.
CiavarellaM.StrozziA.BaldiniA.GiacopiniM.Normalization of load and clearance effects in ball in socket-like replacements. Proc. IMechE, Part H: J. Engineering in Medicine, 2007, 221, 221–601.
41.
PioliA.StrozziA.BaldiniA.GiacopiniM.RosiR.Influence of the initial clearance on the peak stress in connecting-rod small ends. Proc. IMechE, Part D: J. Automobile Engineering, 2009, 223, 223–769.
42.
StrozziA.BaldiniA.GiacopiniM.RosiR.BertocchiE.Contact stresses within a split ring inserted into a circular housing. J. Strain Analysis., 2009, 44, 1–18.
43.
OkuboH.The stress distribution in a shaft press-fitted with a collar. Z. Angew. Math. Mech., 1952, 32, 178–186.
44.
BookerJ. D.TrumanC. E.A statistical study of the coefficient of friction under different loading regimes. J. Physics D: Appl. Phys., 2008, 41, 1–12.
45.
TrumanC. E.BookerJ. D.Analysis of a shrink-fit failure on a gear hub/shaft assembly. Engng Failure Anal., 2007, 14, 557–572.
46.
CroccoloD.De AgostinisM.VincenziN.Recent improvements and design formulae applied to front motorbike suspension. Engng Failure Anal., 2010, 17, 1173–1187.
47.
CroccoloD.De AgostinisM.VincenziN.Static and dynamic strength evaluation of interference fit and adhesively bonded cylindrical joints. Int. J. Adhesion Adhesives, 2010, 30, 359–366.
48.
AstM.RösleH.SchenkR.FEM-Analyse reibschlüssiger Welle-Nabe-Verbindungen. VDI-Berichte 1384, ‘Welle-Nabe-Verbingunen - Systemkomponenten im Wandel’, Fulda, Germany, ISBN 3-18-091384-3, 1998, pp. 227–244.
49.
GeorgeA.StrozziA.RichJ. I.Stress fields in a compressed unconstrained elastomeric O-ring seal and a comparison of computer predictions and experimental results. Tribol. Int., 1987, 20, 237–247.
50.
StrozziA.UnsworthA.Observations on the Paper by O′Carrol et al.. Proc. IMechE, Part H: J. Engineering in Medicine, 1995, 209, 203–205.
51.
BozkayaD.MuftuS.Mechanics of tapered interference fit in dental implants. J. Biomech., 2003, 36, 1649–1658.
52.
AndrisanoA. O.DragoniE.StrozziA.Axisymmetric mechanical analysis of ceramic heads for total hip replacement. Proc. IMechE, Part H: J. Engineering in Medicine, 1990, 204, 157–167.
53.
FesslerH.FrickerD. C.A study of stresses in alumina universal heads of femoral prostheses. Proc. IMechE, Part H: J. Engineering in Medicine, 1989, 203, 15–34.
54.
OlukokoO. A.BeckerA. A.FennerR. T.Three benchmark examples for frictional contact modelling using finite element and boundary element methods. J. Strain Analysis, 1993, 28,293–301.
