Sage Journals: Discover world-class research

Abstract

This paper is concerned with the handling of any object by an articulated multifingered hand. By handling we mean the secure grasp of a general object plus the manipulation of this object by the fingers without motion of the arm on which the hand is mounted. Hypothetical joints are used to express the freedom at the contact of the object with each fingertip. A pair of matrices are introduced that relate the small motions of the joints to the relative displacement of the object and the fingertips and that are derived using reciprocal screws. This analysis permits not only the determination of the necessary conditions for a secure handling of the object but also the investigation of the special configurations that may occur. In the case of a grasp with point contact with friction, a very important result is derived that leads to a considerable sim plification in the analysis of these matrices. It is further shown that there exists a particular point, called the center of the grasp, at which the direction of the force applied to the object does not influence the contact intensities. Following this it is demonstrated that the vector containing the contact intensities, generated by a unit couple applied to the object, generates an ellipsoid defined as the grasp ellipsoid. The two smaller axes of this ellipsoid show where to place the con tacts to minimize the contact forces for a given task. The results are illustrated with numeric examples in appendix C.

Get full access to this article

View all access options for this article.

References

Asada, H. , and Youcef-Toumi, K. 1987. Direct-drive Robots: Theory and Practice. Cambridge, Mass.: MIT Press.

Duffy, J. 1983. Class notes. Department of Mechanical Engineering, University of Florida.

Holzmann, W. , and McCarthy, M. 1985. Computing the friction forces associated with a three-fingered grasp. IEEE J. Robot. Automat. RA-1(4).

Kerr, J.R. 1984. An analysis of multi-fingered hands. Ph.D. dissertation . Department of Mechanical Engineering, Stanford University.

Kerr, D.R. , and Sanger, D.J. 1986. Restraint analysis of a rigid body using frictional elastic contacts. ASME paper no. 86-DET-136.

Kobayashi, H. 1985. Control and geometrical considerations for an articulated hand. Int. J. Robot. Res. 4(1).

Kumar, A. , and Waldron, K.J. 1981. The workspaces of a mechanical manipulator. Trans. ASME Mech. Des. 103:665-672.

Li, Z. , and Sastry, S. 1986. Task oriented optimal grasping by multifingered robot hands. Memorandum no. UCB/ ERL M86/43, Electronics Research Laboratory, University of California, Berkeley.

Lipkin, H. 1985. Geometry and mapping of screws with applications to the hybrid control of robotic manipulators. Ph.D. dissertation. Department of Mechanical Engineering, University of Florida.

10.

Lipkin, H. , and Duffy, J. 1984. On the geometry of orthogonal and reciprocal screws. In Morecki, A., et al., eds: Theory and Practice of Robots and Manipulators, Proceedings RoManSy'84: 5th CISM-IFToMM Sym Udine, pp. 47-56.

11.

Maher, G.M. 1983. Instantaneous kinematics and joint displacement analysis of fully-parallel robotic devices. Ph.D. dissertation. Department of Mechanical Engineering, University of Florida.

12.

Maher, G.M. , and Duffy, J. 1984. A direct determination of the instantaneous kinematics of fully-parallel robot manipulators. ASME paper no. 84-DET-114.

13.

Salisbury, J.K. 1982. Kinematic and force analysis of articulated hands. Ph.D. dissertation. Department of Mechanical Engineering, Stanford University.

14.

Steven, J.L. 1980. Linear Algebra with Applications. New York: Macmillan.

15.

Sugimoto, K. , and Duffy, J. 1981. Determination of extreme distances of a robot hand. Part 2: Robot arms with special geometry. Trans. ASME J. Mech. Des. 103:776-783.

Kinestatic Analysis of Multifingered Hands

Abstract

Get full access to this article

References