The effect of second-phase particles on the formation of recrystallisation textures in Al–Fe alloy sheet was analysed. Four commercial AA 8xxx series alloys were chosen on the basis of their Fe and Si contents, one alloy additionally comprised Mn. Main focus was laid on the efficiency of particle stimulated nucleation (PSN) at the large constituent phases. As known from other Al alloys, the recrystallisation textures of the present AA 8xxx alloys are composed of new grains forming at three distinct nucleation sites, viz. cube bands, pre-existing grain boundaries and coarse intermetallic particles. The efficiency of each of these nucleation mechanisms strongly depends on the details of the as-deformed microstructure, especially on the size distribution of the constituent particles.
KerthWAmannERäberX, et al.Aluminium foil production. Int Metall Rev1975; 20: 185–207.
2.
TsuchidaSBabaY. Development of aluminum alloys for packaging in Japan. In: MorrisJGMerchantHDWestermanEJMorrisPL (eds) Aluminum alloys for packaging. Warrendale, PA: TMS, 1993, pp.17–29.
MahonGJMarshallGJ. Microstructure-property relationships in O-temper foil alloys. JOM1996; 48: 39–42.
5.
FepponJ-MChenalB. Grain size and mechanical properties of aluminium thin foils used in packaging applications. Matériaux Tech2002; 90: 59–65.
6.
HasencleverJ. Microstructure and properties of AlFe-alloys (AA 1050 – AA 8021) for packaging. In: NieJFMortonAJMuddleBC (eds) Proc. ICAA 9. North Melbourne, Australia: Inst. Mater. Eng. Australasia Ltd, 2004, pp.867–872.
7.
HamertonR. Al 99,5 for packaging and foil applications. In: HirschJ (ed) Virtual fabrication of aluminium products. Weinheim, Germany: Wiley-VCH, 2006, pp.13–18.
8.
KelesODundarM. Aluminum foil: its typical quality problems and their causes. J Mater Proc Technol2007; 186: 125–137.
9.
SantoraEBernederJSimetsbergerF, et al.Mechanical properties evolution for 8xxx foil stock materials by alloy optimization – literature review and experimental research. In: ChesonisC (ed) Light metals 2019. Warrendale, PA: TMS, 2019, pp.365–372.
10.
EkströmH-ECharlierP. Strip cast aluminium foil. In: MorrisJGDasSKGoodrichHS (eds) Aluminium alloys for packaging II. Warrendale, PA: TMS, 1996, pp.245–251.
11.
KarlíkMSieglJSlámováM, et al.Study of the damage of AA 8006 twin-roll cast thin sheets during forming of heat exchanger fins. Mater Sci Forum2000; 331–337: 619–624.
12.
SandersRE JrHollinsheadPASimielliEA. Industrial development of non-heat treatable aluminum alloys. In: NieJFMortonAJMuddleBC (eds) Proc. ICAA 9. North Melbourne, Australia: Inst. Mater. Eng. Australasia Ltd., 2004, pp.53–64.
13.
DelijićKAsanovićVRadonjićD. Mechanical and corrosion properties of AA8011 sheets and foils. Mater Tehnol2006; 40: 83–88.
14.
KabilAMollaoğlu AltunerHMeydanogluO. Effect of cold rolling prior to homogenization heat treatment on the microstructural evolution and mechanical properties of twin-roll cast 8026 aluminum alloy. In: WagstaffS (ed) Light metals 2024. Warrendale, PA: TMS, 2024, pp.362–368.
15.
LaptyevaGSchäferCKarhausenK-F, et al.Impact of solute state and precipitations on the properties of 8xxx alloys after cold rolling and recrystallization. In: JohnsonJA (ed) Light metals 2010. Warrendale, PA: TMS, 2010, pp.585–590.
16.
EnglerOLaptyevaGWangN. Impact of homogenization on microchemistry and recrystallization of the Al–Fe–Mn alloy AA 8006. Mater Char2013; 79: 60–75.
17.
VelmanirajanKAnuradhaKSyed Abu ThaheerA, et al.Experimental investigation of forming limit, void coalescence and crystallographic textures of aluminum alloy 8011 sheet annealed at various temperatures. Arch Civ Mech Eng2014; 14: 398–416.
18.
AryshenskiiEHirschJBazhinV, et al.Impact of Zener-Hollomon parameter on substructure and texture evolution during thermomechanical treatment of iron-containing wrought aluminium alloys. Trans Nonferrous Met Soc China2019; 29: 893–906.
19.
ShiCWuYMaoD, et al.Effect of annealing temperature on microstructure and properties of 8011 cold-rolled sheet. IOP Conf Series: Mater Sci Eng2019; 612: 032165.
20.
VončinaMKresnikKVolšakD, et al.Effects of homogenization conditions on the microstructure evolution of aluminium alloy EN AW 8006. Metals (Basel)2020; 10: 419.
21.
SantoraEPachnekFFalkingerG, et al.The effect of homogenization and hot deformation on the recrystallization behavior in aluminum alloy AA8079. Metall Mater Trans A2024; 55: 4914–4927.
22.
PanYShenYCaoL. Effect of intermediate annealing on microstructure and cold rolling hardness of AlFeMn alloy. Metals (Basel)2024; 14: 785.
23.
OscarssonAHutchinsonWBEkströmH-E. Influence of initial microstructure on texture and earing in aluminium sheet after cold rolling and annealing. Mater Sci Technol1991; 7: 554–564.
24.
EnglerO. Nucleation and growth during recrystallisation of aluminium alloys investigated by local texture analysis. Mater Sci Technol1996; 12: 859–872.
25.
VatneHEBenumSDaalandO, et al.The effect of particles on recrystallisation textures and microstructures. Texture Stress Microstruct1996; 26: 385–412.
26.
DohertyRD. Recrystallization and texture. Prog Mater Sci1997; 42: 39–58.
27.
DriverJEnglerO. Design of aluminum rolling processes for foil, sheet, and plate. In: TottenGEFunataniKXieL (eds) Handbook of metallurgical process design. New York, NY: Marcel Dekker, 2004, pp.69–114.
28.
EnglerOHirschJ. Control of recrystallisation texture and texture-related properties in industrial production of aluminium sheet. Int J Mater Res2009; 100: 564–575.
29.
HumphreysFJRohrerGSRollettAD. Recrystallization and related annealing phenomena. 3rd ed. Amsterdam, The Netherlands: Elsevier, 2017.
30.
HuangKMarthinsenKZhaoQ, et al.The double-edge effect of second-phase particles on the recrystallization behaviour and associated mechanical properties of metallic materials. Prog Mater Sci2018; 92: 284–359.
31.
GrasserbauerJFalkingerGUggowitzerPJ, et al.Influence of Fe and Mn on the microstructure formation in 5xxx alloys − Part II: evolution of grain size and texture. Materials (Basel)2021; 14: 3312.
32.
KnipschildtEFF. Nucleation of recrystallization. Mater Sci Technol2022; 38: 765–779.
33.
HumphreysFJ. The nucleation of recrystallization at second phase particles in deformed aluminium. Acta Metall1977; 25: 1323–1344.
34.
DaviesRKRandleVMarshallGJ. Continuous recrystallization-related phenomena in a commercial Al–Fe–Si alloy. Acta Mater1998; 46: 6021–6032.
35.
RyuJHLeeDN. The effect of precipitation on the evolution of recrystallization textures in an AA 8011 aluminum alloy sheet. Mater Sci Eng A2002; 336: 225–232.
36.
RoyRKKarSDasS. Evolution of microstructure and mechanical properties during annealing of cold-rolled AA8011 alloy. J Alloys Compd2009; 468: 122–129.
37.
SukhoparOGottsteinG. In-situ annealing and computation study of cube texture development in a commercial aluminum alloy. Int J Mater Res2016; 107: 979–987.
38.
KumarRGuptaAKumarA, et al.Microstructure and texture development during deformation and recrystallization in strip cast AA8011 aluminum alloy. J Alloys Compd2018; 742: 369–382.
39.
ChenWChenMJinX, et al.Effect of heating rate during annealing on microstructure and texture evolution of AA8021 aluminum foil. Mater Res Express2020; 7: 096514.
40.
KranerJSmolarTVolšakD, et al.Influence of the hot-rolling technique for EN AW-8021B aluminium alloy on the microstructural properties of a cold-rolled foil. Mater Tehnol2021; 55: 773–779.
41.
EnglerOAegerterJCalmerD. Control of texture and earing in aluminium alloy AA8011A-H14 closure stock. Mater Sci Eng A2020; 775: 138965.
42.
KranerJKimKIKimB, et al.Relevance of cold-rolling technology for the texture and anisotropy of EN AW-8011A aluminum alloys. Mater Tehnol2023; 57: 631–638.
43.
LangCHiscockMHollandJ, et al.New developments in automated particle analysis in the electron microscope – from micro to nano. Microsc Microanal2015; 21: 337–338.
44.
AnselminoEMirouxAvan der ZwaagS. Dispersoid quantification and size distribution in hot and cold processed AA3103. Mater Char2004; 52: 289–300.
45.
EnglerOZaeffererSRandleV. Introduction to texture analysis: macrotexture, microtexture and orientation mapping. 3rd ed.Boca Raton, FL: CRC Press, 2024.
46.
BungeHJ. Texture analysis in materials science. London: Butterworths, 1982.
47.
BaleCWChartrandPDegterovSA, et al.Factsage thermochemical software and databases. Calphad2002; 26: 189–228.
48.
BelovNAAksenovAAEskinDG. Iron in aluminum alloys: impurity and alloying element. Boca Raton, FL: CRC Press, 2002.
49.
StefániayVGrigerATurmezeyT. Intermetallic phases in the aluminium-side corner of the AlFeSi-alloy system. J Mater Sci1987; 22: 539–546.
50.
AllenCMO’ReillyKAQCantorB, et al.Intermetallic phase selection in 1XXX Al alloys. Prog Mater Sci1998; 43: 89–170.
LentzMLaptyevaGEnglerO. Characterization of second-phase particles in two aluminium foil alloys. J Alloys Compd2016; 660: 276–288.
53.
DavignonGSerneelsAVerlindenB, et al.An isothermal section at 550 °C in the Al-rich corner of the Al–Fe–Mn–Si system. Metall Mater Trans A1996; 27: 3357–3361.
54.
EnglerO. Correlating crystallographic texture with anisotropic properties and sheet metal forming of aluminium alloys. J Mater Res Technol2025; 35: 514–522.
55.
DillamoreILKatohH. The mechanisms of recrystallization in cubic metals with particular reference to their orientation-dependence. Metal Sci1974; 8: 73–83.
56.
DonsALNesE. Nucleation of cube texture in aluminium. Mater Sci Technol1986; 2: 8–18.
57.
WeilandHHirschJR. Microstructure and local texture in hot rolled aluminum. Texture Stress Microstruct1991; 14–18: 647–652.
58.
DaalandONesE. Origin of cube texture during hot rolling of commercial Al-Mn-Mg alloys. Acta Mater1996; 44: 1389–1411.
59.
EnglerO. On the origin of the R-orientation in the recrystallization textures of aluminum alloys. Metall Mater Trans A1999; 30: 1517–1527.
60.
SidorJJDecroosKPetrovRH, et al.Evolution of recrystallization textures in particle containing al alloys after various rolling reductions: experimental study and modeling. Int J Plast2015; 66: 119–137.
61.
VatneHEFuruTØrsundR, et al.Modelling recrystallization after hot deformation of aluminium. Acta Mater1996; 44: 4463–4473.
62.
EnglerOKuhnkeKHasencleverJ. Development of intermetallic particles during solidification and homogenization of two AA 5xxx series Al-Mg alloys with different Mg contents. J Alloys Compd2017; 728: 669–681.
63.
EnglerOBrüggemannTHasencleverJ. Evolution of micro-chemistry during solidification and homogenisation of AA 3xxx aluminium-manganese alloys. Mater Sci Technol2021; 37: 893–908.
64.
LiuWCLiZManC-S. Effect of heating rate on the microstructure and texture of continuous cast AA 3105 aluminum alloy. Mater Sci Eng A2008; 478: 173–180.
65.
ShenFWangBYiD, et al.Effects of heating rate during solid-solution treatment on microstructure and fatigue properties of AA2524 T3 al–cu–mg sheet. Mater Des2016; 104: 116–125.
66.
LeiXChapuisAGuoQ, et al.Effect of prior strain and heating rate on the microstructures, mechanical properties and plastic anisotropy of AA5182 sheets. J Mater Res Technol2025; 36: 8972–8982.
67.
HigginsonRLAindowMBatePS. The effect of finely dispersed particles on primary recrystallisation textures in Al-Mn-Si alloys. Mater Sci Eng A1997; 225: 9–21.
68.
VatneHEEnglerONesE. The influence of particles on the recrystallisation textures and microstructures of the aluminium alloy AA3103. Mater Sci Technol1997; 13: 93–102.
69.
LiuWMaMYangF. Effect of the heat treatment on the cube recrystallization texture of Al-Mn-Mg aluminum alloy. Metall Mater Trans A2013; 44: 2857–2868.
