Structure formation during the crystallization of a melt Al – 16.5% wt. Si treated with packages of unipolar electrical pulses of various frequencies and amplitudes have been studied. Grinding of primary silicon crystals was observed, the size and morphology of which depend on the electric current density. DTA showed a significant change in the parameters of both melting and solidification processes. X-ray diffraction studies have established the formation of additional silicon phases: polytype silicon, and silicon with tetragonal and bcc structures. The results obtained are explained by the transformation of the structure and a decrease in the degree of micro inhomogeneity of the Al-Si melt a change in the short-range order of Si-Si atoms.
AlshmriFAtkinsonHVHainsworthSV, et al.Dry sliding wear of aluminium-high silicon hypereutectic alloys. Wear2014; 313: 106–116.
2.
AiqinWLijunZԽXIEJ. Effects of cerium and phosphorus on microstructures and properties of hypereutectic Al-21% Si alloy. J Rare Earths2013; 31: 522–525.
3.
PengC. Preparation of Al-Si alloys by a rapid solidification and powder metallurgy route. JMADE2015; 87: 996–1002.
4.
PrasadBKVenkateswarluKModiOP, et al.Sliding wear behavior of some Al-Si alloys: role of shape and size of Si particles and test conditions. Metall Mater Trans A1998; 29: 2747–2752.
5.
KumarKGB. Influence of refinement and modification on dry sliding wear behavior of hypereutectic Al-Si cast alloys. Adv Mater Res2013; 685: 112–116.
6.
LiPNikitinVIKandalovaEG,et al.Effect of melt overheating, cooling and solidification rates on Al – 16wt .% Si alloy structure. Mater Sci Eng A2002; 332: 371–374.
7.
CaiZWangRZhangC, et al.Characterization of rapidly solidified Al-27 Si hypereutectic alloy: effect of solidification condition. J Mater Eng Perform2015; 24: 1226–1236.
8.
KangHSYoonWYKimKH, et al.Microstructure selections in the undercooled hypereutectic Al-Si alloys. Mater Sci Eng A2005; 404: 117–123.
9.
OkayasuMTakeuchiSShiraishiT. Crystallisation characteristics of primary silicon particles in cast hypereutectic Al-Si alloy. Int J Cast Met Res2013; 26: 105–113.
10.
LasaL. Wear behaviour of eutectic and hypereutectic Al – Si – Cu – Mg casting alloys tested against a composite brake pad. Mater Sci Eng А2003; 363: 193–202.
11.
BhattacharyaSAlpasAT. Role of sliding-induced tribofilms on fracture of particles in aluminium – silicon alloys. Wear2013; 301: 707–716.
12.
ChandrashekharaiahTMKoriSA. Effect of grain refinement and modification on the dry sliding wear behaviour of eutectic Al-Si alloys. Tribol Int2009; 42: 59–65.
13.
FeyzullahogluEErturkATGuvenEA. Influence of forging and heat treatment on wear properties of Al–Si and Al–Pb bearing alloys in oil lubricated conditions. Trans Nonferrous Met Soc China2013; 23: 3575–3583.
14.
ZengJZhuCWangW, et al.Evolution of primary Si phase, surface roughness and mechanical properties of hypereutectic Al–Si alloys with different Si contents and cooling rates. Philos Mag Lett.2020; 100: 581–587.
15.
VatanseverFErturkATKarabayS. Improving mechanical properties of AlSi10Mg aluminum alloy using ultrasonic melt treatment combined with T6 heat treatment. Kovove Mater2019; 57: 33–43.
16.
YinCLuZWeiX, et al.High bending strength hypereutectic Al-22Si-0.2Fe-0.1Cu-Re alloy fabricated by selective laser melting. Metals2021; 11: 28.
17.
WangQLiLZhouR, et al.Rheological behavior of semisolid hypereutectic Al–Si alloys. J Mater Res2019; 34: 2105–2113.
18.
XiaoweiLXiaoweiSXiaoweiW. A method for improving the mechanical properties of a hypereutectic Al–Si alloy by introducing the α-Al phase. Int J Mater Res2016; 107: 422–428.
19.
TsurkinVNIvanovAZaporozhetsY,et al.Polyvariant method of conductive electric current treatment of melt. Elektronnaya Obrabotka Materialov2023; 59: 25–36.
20.
ZhangYXuYYeC, et al.Relevance of electrical current distribution to the forced flow and grain refinement in solidified Al-Si hypoeutectic alloy. Sci Rep2018; 8: 1–11.
21.
ChoiJLaMKimD, et al.Effect of electric current on the microstructural refinement of pure aluminum. J Mater Res Technol2021; 12: 818–830.
22.
PlotkowskiAJ. Refinement of the cast microstructure of hypereutectic aluminum-silicon alloys with an applied electric potential. Masters Theses, Grand Valley State University USA, 2012.
23.
LiNZhangLZhangR, et al.Research on grain refinement in hypoeutectic Al-Si alloy during solidification under an alternating electric current pulse. Metals2019; 9: 71.
24.
ZhangYRäbigerDWillersB,et al.The effect of pulsed electrical currents on the formation of macrosegregation in solidifying Al–Si hypoeutectic phases. Int J Cast Met Res2017; 30: 13–19.
25.
GuoJWangFZhangS, et al.Effect of high-frequency electric pulse on the solidification microstructure and properties of hypoeutectic Al-Si alloy. Materials2024; 17: 68.
26.
PrigunovaAGZhidkovEABabiukVD. Structure, phase composition and properties of AK12M2MgN alloy with increased iron content, treated in the liquid state by electric current. Metalozn Obrobka Met2023; 29: 3–14(in Ukr.). doi:10.15407/mom2023.02.003
27.
PrigunovaAGKoshelevMVBorisovAG. Effect of unipolar pulsed electric current treatment of the melt of Al – 8 Wt-% Si – 0.7 Wt-% Fe alloy on iron-containing phases formation and mechanical properties of castings. Mater Sci Tech2022; 38: 246–253.
28.
AliyuMAQiJ-GLiY, et al.The effects of electric pulse modification on eutectic Al-12.6%Si alloy. J Mech Civ Eng2014; 11: 94–98.
29.
ZhangYSongCZhuL, et al.Influence of electric-current pulse treatment on the formation of regular eutectic morphology in an Al-Si eutectic alloy. Metall Mater Trans B2011; 42: 604–611.
30.
PetrovSSPrigunovaAGPrigunovSV,et al.The structure of hypereutectic silumins when modifying melts with electric current. Sci Infor J: Met Sci Therm Process Met2007; 1: 53–61(in Rus.).
31.
Ban ACHanYBaQ,et al.Influence of pulse electric current on solidification structures of Al-Si alloys. Mater Sci Forum2007; 546-549: 723–728.
32.
HeLJWangJZQiJG, et al.Influences of acting parameters of electric pulse modification on the Al-22%Si-1.5%Cu alloy. Adv Mater Res2011; 299–300: 233–237.
33.
ZhaoZFWangJZQiJG, et al.Study on the influence of different pulse temperatures on Al-22%Si alloy solidification structure. Adv Mater Res2011; 299–300: 566–571.
34.
SaltykovSA. Stereometric metallographyMoskov. Metallurgy, - 1976. - 272 p.
35.
BoettingerWKattnerUMoonK,et al.NIST Recommended Practice Guide: DTA and Heat-Flux DSC Measurements of Alloy Melting and Freezing, Elsevier, Kidlington, −1, [online], https://tsapps.nist.gov/publication/get_pdf.cfm?pub_id=901091 (2006, accessed April 29, 2024).
36.
PiątkowskiJGaldzikB. Testing phase changes in Al-Si alloys with application of thermal analysis and differential calorimetric analysis. Metalurgija2013; 52: 469–472.
