High-current gas tungsten arc welding of Ni-base superalloy Haynes 282: correlating heat input with weld profile,microstructure,hardness and indentation size effect
Restricted accessResearch articleFirst published online October, 2024
High-current gas tungsten arc welding of Ni-base superalloy Haynes 282: correlating heat input with weld profile,microstructure,hardness and indentation size effect
Increasing the linear heat input during high-current gas tungsten arc welding (GTAW) of Haynes 282 leads to a progressive change from conduction mode welding to one with keyhole formation. It coincides with changes in the melt pool geometry and spatial variation of microhardness in the heat affected zone (HAZ). The latter originates from heat input dependent changes in the heating/cooling rates which alter the dissolution/re-precipitation characteristics of fine grain boundary carbides. The load-dependence of microhardness of all weld zones is shown to follow a type-I indentation size effect (ISE). Nanoindentation experiments are carried out to quantify the ISE and extract local plastic properties, demonstrating a qualitatively different mechanical response of the FZ compared to the base metal and the HAZ.
SteenWMMazumderJ. Laser welding. In SteenW. M.MazumderJ. (Eds.), Laser material processing, London: Springer, 2010, pp. 199–201. https://doi.org/10.1007/978-1-84996-062-5_5
2.
JarvisBL. Keyhole gas tungsten arc welding: a new process variant. PhD Thesis, University of Wollongong. 2001. Retrieved fromhttps://ro.uow.edu.au/theses/1833
LiuZFangYCuiS, et al.Keyhole thermal behavior in GTAW welding process. Int J Therm Sci2017; 114: 352–362.
5.
KumarKSateesh KumarCMasantaM,et al.A review on TIG welding technology variants and its effect on weld geometry. Mater Today Proc2022; 50: 999–1004.
6.
TekerTKursunT. Weldability of AA6063 alloys by using keyhole gas tungsten arc welding technique. Met Material2021; 52: 237–242.
7.
ShortAB. Gas tungsten arc welding of α + β titanium alloys: a review. Mater Sci Technol2009; 25: 309–324.
8.
LathabaiSJarvisBLBartonKJ. Comparison of keyhole and conventional gas tungsten arc welds in commercially pure titanium. Mater Sci Eng A2001; 299: 81–93.
9.
FengYLuoZLiuZ, et al.Keyhole gas tungsten arc welding of AISI 316L stainless steel. Mater Des2015; 85: 24–31.
10.
LiFWangBHanL, et al.Effect of Ni addition on microstructure evolution keyhole-GTAW WM of a duplex stainless steel. J Phys: Conf Ser2021; 1906: 012048.
11.
XuanYYangJLiuH, et al.Microstructure and mechanical properties of Invar36 alloy joints using keyhole TIG welding. Sci Technol Weld Joining2020; 25: 712–718.
12.
DuPontJNLippoldJCKiserSD. Welding metallurgy and weldability of nickel-base alloys. Hoboken, NJ, USA: John Wiley & Sons, Inc, 2009. https://doi.org/10.1002/9780470500262
13.
SiefertJAShingledeckerJPDuPontJN,et al.Weldability and weld performance of candidate nickel based superalloys for advanced ultrasupercritical fossil power plants part II: weldability and cross-weld creep performance. Sci Technol Weld Joining2016; 21: 397–427.
14.
DavidSABabuSSVitekJM. Weldability and microstructure development in nickel-base superalloys.Oak Ridge, TN (United States): Oak Ridge National Lab.(ORNL), 1997.
15.
AriasetaASadeghiniaNAnderssonJ,et al.Keyhole TIG welding of newly developed nickel-based superalloy VDM alloy 780. Welding in the World2023; 67: 209–222.
16.
AriasetaAPickDAnderssonJ,et al.Keyhole TIG welding of new co-lean nickel-based superalloy G27. In OttEAAnderssonJSudbrackC, et al. (eds) Proceedings of the 10th International Symposium on Superalloy 718 and Derivatives. Cham: Springer Nature Switzerland, 2023, pp. 807–824. https://doi.org/10.1007/978-3-031-27447-3_48
17.
AthiraKSChatterjeeS. Effect of keyhole gas tungsten arc welding and post-welding heat treatment on microstructure and hardness of inconel 740H. J Mater Eng Perform2023: 1544–1024. https://doi.org/10.1007/s11665-023-08831-3
18.
PikeLM. Development of a fabricable gamma-prime (γ′) strengthened superalloy. Superalloys2008; 2008, 191–200.
19.
KrugerKL. HAYNES 282 Alloy. In Materials for ultra-supercritical and advanced ultra-supercritical power plants. United Kingdom: Woodhead Publishing, Elsevier, 2017, pp. 511–545. https://doi.org/10.1016/B978-0-08-100552-1.00015-4.
20.
OsobaLOOjoOA. Influence of laser welding heat input on HAZ cracking in newly developed Haynes 282 superalloy. Mater Sci Technol2012; 28: 431–436.
21.
OsobaLODingRGOjoOA. Improved resistance to Laser weld heat-affected zone microfissuring in a newly developed superalloy HAYNES 282. Metall Mater Trans A2012; 43: 4281–4295.
22.
OsobaLODingRGOjoOA. Microstructural analysis of laser weld fusion zone in Haynes 282 superalloy. Mater Charact2012; 65: 93–99.
23.
OsobaLOKhanAKAdeosunSO. Cracking susceptibility after post-weld heat treatment in Haynes 282 nickel based superalloy. Acta Metall Sin (Engl Lett)2013; 26: 747–753.
24.
KomarasamyMSmithCDarsellJ, et al.Microstructure and mechanical properties of friction stir welded Haynes 282. Mater Charact2021; 182: 111558.
25.
HanningFAnderssonJ. Weldability of wrought Haynes® 282® repair welded using manual gas tungsten arc welding. Weld World2018; 62: 39–45.
26.
HanningFSinghGAnderssonJ. The effect of grain size on the susceptibility towards strain age cracking of wrought Haynes® 282®. In SäfstenK.ElghF. (eds) Advances in Transdisciplinary Engineering. Amsterdam: IOS Press, 2020, pp.407–416. https://doi.org/10.3233/ATDE200178.
27.
CaronJL. Weldability and welding metallurgy of Haynes 282 alloy. In 8th International symposium on superalloy 718 and derivatives. Unites States: John Wiley & Sons, 2014, pp. 273–286. https://doi.org/10.1002/9781119016854.ch23.
28.
CaronJPikeL. Weldability of HAYNES 282 superalloy after long-term thermal exposure. MATEC Web Conf2014; 14: 13003.
29.
SantellaMChenXFMaziaszP, et al.Properties of a thick-section narrow-gap gas tungsten arc weld of cast Haynes 282. Weld World2021; 65: 961–971.
30.
JuangSCTarngYS. Process parameter selection for optimizing the weld pool geometry in the tungsten inert gas welding of stainless steel. J Mater Process Technol2002; 122: 33–37.
31.
ZengXMLucasJFangMTC. Use of neural networks for parameter prediction and quality inspection in TIG welding. Trans Inst Meas Control1993; 15: 87–95.
32.
ZhangYMKovacevicRLiL. Characterization and real-time measurement of geometrical appearance of the weld pool. Int J Mach Tools Manuf1996; 36: 799–816.
33.
PharrGMHerbertEGGaoY. The indentation size effect: a critical examination of experimental observations and mechanistic interpretations. Annu Rev Mater Res2010; 40: 271–292.
34.
SangwalK. On the reverse indentation size effect and microhardness measurement of solids. Mater Chem Phys2000; 63: 145–152.
35.
SangwalK. Microhardness of as-grown and annealed lead sulphide crystals. J Mater Sci1989; 24: 1128–1132.
36.
NixWDGaoH. Indentation size effects in crystalline materials: a law for strain gradient plasticity. J Mech Phys Solids1998; 46: 411–425.
37.
Van RooyenNBhattacharyyaMCharitI, et al.Indentation investigation of 304L stainless steel friction stir weld simulated crack repair. Mater Sci Eng A2022; 836: 142691.
38.
ZhangCGongBDengC,et al.Computational prediction of mechanical properties of a C-Mn weld metal based on the microstructures and micromechanical properties. Mater Sci Eng A2017; 685: 310–316.
39.
HuangYZhouCChenK, et al.Nanoindentation size effects of mechanical and creep performance in Ni-based superalloy. Mater Sci Technol2023; 39: 1543–1554.
40.
JiXXiaoGZhaoW, et al.Loading rate sensitivity of nickel-based single crystal superalloys characterized by nanoindentation. Int J Solids Struct2022; 234–235: 111272. https://doi.org/10.1016/j.ijsolstr.2021.111272
41.
MatysiakHZagorskaMAnderssonJ, et al.Microstructure of Haynes® 282® superalloy after vacuum induction melting and investment casting of thin-walled components. Materials2013; 6: 5016–5037.
MendasMBenayounSMiloudMH,et al.Microhardness model based on geometrically necessary dislocations for heterogeneous material. J Mater Res Technol2021; 15: 2792–2801.
Supplementary Material
Please find the following supplemental material available below.
For Open Access articles published under a Creative Commons License, all supplemental material carries the same license as the article it is associated with.
For non-Open Access articles published, all supplemental material carries a non-exclusive license, and permission requests for re-use of supplemental material or any part of supplemental material shall be sent directly to the copyright owner as specified in the copyright notice associated with the article.
