In this study, AZ31B-H24 and WE43-T5 Mg alloys were joined using friction stir welding. The effect of base material position, tool offset and rotational speed on the microstructure and mechanical properties was investigated. With AZ31B on the advancing side (AS), distinct layers of both materials were observed in the nugget zone (NZ), while material mixing in the NZ was better with WE43 on the AS. A maximum joint strength of 207 MPa (97% of AZ31B) was observed with AZ31B on the AS without tool offset and a tool rotation speed of 600 RPM. The failure location was at the thermo-mechanically affected zone/heat-affected zone of AZ31B side when AZ31B was on the AS, while joints with WE43 on the AS failed in the NZ.
YangZLiJPZhangJX, et al.Review on research and development of magnesium alloys. Acta Metall Sin (English Lett)2008; 21: 313–328.
2.
AghionEBronfinB. Magnesium alloys development towards the 21st century. Mater Sci Forum2000; 350-351: 19–30.
3.
TurowskaAAdamiecJ. Mechanical properties of WE43 magnesium alloy joint at elevated temperature. Arch Metall Mater2015; 60: 2695–2702.
4.
SongGDiaoZLvX,et al.TIG and laser–TIG hybrid filler wire welding of casting and wrought dissimilar magnesium alloy. J Manuf Process2018; 34: 204–214.
5.
QuanYChenZGongX,et al.CO2 laser beam welding of dissimilar magnesium-based alloys. Mater Sci Eng A2008; 496: 45–51.
6.
GaoMCaoYZengXY,et al.Mechanical properties and microstructures of hybrid laser MIG welded dissimilar Mg–Al–Zn alloys. Sci Technol Weld Join2010; 15: 638–645.
7.
SomasekharanACMurrLE. Microstructures in friction-stir welded dissimilar magnesium alloys and magnesium alloys to 6061-T6 aluminum alloy. Mater Charact2004; 52: 49–64.
8.
NandanRDebroyTBhadeshiaHKDH. Recent advances in friction stir welding – process, weldment structure and properties. Prog Mater Sci2008; 53: 980–1023.
9.
LeeWBYeonYMJungSB. The joint properties of dissimilar formed Al alloys by friction stir welding according to the fixed location of materials. Scr Mater2003; 49: 423–428.
10.
LiuDNishioHNakataK. Anisotropic property of material arrangement in friction stir welding of dissimilar Mg alloys. Mater Des2011; 32: 4818–4824.
11.
LiuDXinRZhengX, et al.Microstructure and mechanical properties of friction stir welded dissimilar Mg alloys of ZK60-AZ31. Mater Sci Eng A2013; 561: 419–426.
12.
KumarKKailasSV. Positional dependence of material flow in friction stir welding: analysis of joint line remnant and its relevance to dissimilar metal welding. Sci Technol Weld Join2010; 15: 305–311.
13.
CavalierePPanellaF. Effect of tool position on the fatigue properties of dissimilar 2024-7075 sheets joined by friction stir welding. J Mater Process Technol2008; 206: 249–255.
14.
FirouzdorVKouS. Al-to-Mg friction stir welding: effect of material position, travel speed, and rotation speed. Metall Mater Trans A Phys Metall Mater Sci2010; 41: 2914–2935.
15.
ZhangJHuangGLiuS, et al.Microstructure evolution and mechanical properties of friction stir welded dissimilar joints of as-extruded AM60 and AZ31 alloys. Mater Sci Eng A2019; 759: 479–489.
16.
ZhangJChenXXiaD, et al.Improving performance of friction stir welded AZ31/AM60 dissimilar joint by adjusting texture distribution and microstructure. Mater Sci Eng A2020; 778: 139088.
17.
NieJFMuddleBC. Characterisation of strengthening precipitate phases in a Mg-Y-Nd alloy. Acta Mater2000; 48: 1691–1703.
18.
LuoCLiXSongD, et al.Microstructure evolution and mechanical properties of friction stir welded dissimilar joints of Mg–Zn–Gd and Mg–Al–Zn alloys. Mater Sci Eng A2016; 664: 103–113.
19.
MastanaiahPSharmaAReddyGM. Dissimilar friction stir welds in AA2219-AA5083 aluminium alloys: effect of process parameters on material inter-mixing, defect formation, and mechanical properties. Trans Indian Inst Met2016; 69: 1397–1415.
20.
ZhangMXKellyPM. Morphology and crystallography of Mg24Y5 precipitate in Mg–Y alloy. Scr Mater2003; 48: 379–384.
21.
KangYHuangZZhaoH, et al.Comparative study of hot deformation behavior and microstructure evolution of as-cast and extruded WE43 magnesium alloy. Metals (Basel)2020; 10: 1–17.
22.
ChoJHBoyceDEDawsonPR. Modeling strain hardening and texture evolution in friction stir welding of stainless steel. Mater Sci Eng A2005; 398: 146–163.
23.
CrawfordRCookGEStraussAM, et al.Experimental defect analysis and force prediction simulation of high weld pitch friction stir welding. Sci Technol Weld Join2006; 11: 657–665.
24.
AlihaMRMShahheidariMBisadiM, et al.Mechanical and metallurgical properties of dissimilar AA6061-T6 and AA7277-T6 joint made by FSW technique. Int J Adv Manuf Technol2016; 86: 2551–2565.
25.
KumarKKailasSV. The role of friction stir welding tool on material flow and weld formation. Mater Sci Eng A2008; 485: 367–374.
26.
DengYQiuZZuoD, et al.Influence of tool offset on microstructure and properties of Mg/Al dissimilar alloys by friction stir welding joints at low heat input. Int J Adv Manuf Technol2020; 109: 2845–2853.
27.
FratiniLBuffaGPalmeriD, et al.Material flow in FSW of AA7075-T6 butt joints: continuous dynamic recrystallization phenomena. J Eng Mater Technol Trans ASME2006; 128: 428–435.
28.
SeidelTUReynoldsAP. Visualization of the material flow in AA2195 friction-stir welds using a marker insert technique. Metall Mater Trans A2001; 32: 2879–2884.
29.
ŚliwaREBalawenderTHadasikE, et al.Metal forming of lightweight magnesium alloys for aviation applications. Arch Metall Mater2017; 62: 1559–1566.
30.
KimYGFujiiHTsumuraT, et al.Three defect types in friction stir welding of aluminum die casting alloy. Mater Sci Eng A2006; 415: 250–254.
31.
BattezzatiLGreerA. The viscosity of liquid metals and alloys. Acta Metallurgica1989; 37: 1791–1802.
32.
TurchiPA. Viscosity and surface tension of metals (No. LLNL-TR-750486). Lawrence Livermore National Lab (LLNL), Livermore, CA, 2018.
33.
GotawalaNShrivastavaA. Analysis of material distribution in dissimilar friction stir welded joints of Al 1050 and copper. J Manuf Process2020; 57: 725–736.
34.
ChangCILeeCJHuangJC. Relationship between grain size and Zener–Holloman parameter during friction stir processing in AZ31 Mg alloys. Scr Mater2004; 51: 509–514.
35.
ChowdhurySHChenDLBholeSD, et al.Friction stir welded AZ31 magnesium alloy: microstructure, texture, and tensile properties. Metall Mater Trans A Phys Metall Mater Sci2013; 44: 323–336.
36.
AfrinNChenDLCaoX,et al.Microstructure and tensile properties of friction stir welded AZ31B magnesium alloy. Mater Sci Eng A2008; 472: 179–186.
37.
WooWChooHBrownDW, et al.Texture variation and its influence on the tensile behavior of a friction-stir processed magnesium alloy. Scr Mater2006; 54: 1859–1864.
38.
ParkSHCSatoYSKokawaH. Effect of micro-texture on fracture location in friction stir weld of Mg alloy AZ61 during tensile test. Scr Mater2003; 49: 161–166.
39.
CheepuMBaekHJKimYS,et al.Melting characteristics of C-type filler metal in GTAW. Weld J2023; 102: 201–216.
40.
SarilaVKoneruHVCheepuM, et al.Microstructural and mechanical properties of AZ31B to AA6061 dissimilar joints fabricated by refill friction stir spot welding. J Manuf Mater Process2022; 6: 95.
41.
KotariSPunnaEGangadharSM, et al.Dissimilar metals TIG welding-brazing of AZ31 magnesium alloy to 304 stainless steel. Mater Today Proc2021; 39: 1549–1552.
42.
CheepuMBaekHJKimYS,et al.Penetration estimation of GTAW with C-type filler by net heat input ratio. Weld J2022; 101: 240–248.
