Identifying Critical Process Variables in Poly(ethylene Terephthalate) Melt Spinning 1

Abstract

A quantitative procedure for identifying critical operating conditions and material properties for the melt spinning of poly(ethylene terephthalate) (PET) is considered. The method is based on the experimental observation that for vitrified polymers like polystyrene and PET spun at speeds below 3000 m/minute, the molecular orientation of the as-spun fiber is uniquely determined by σ _L , the spinline stress at the glass transition temperature. Using a constant tension model that predicts σ _L , a sensitivity analysis of the fiber orientation to changes in process variables is investigated. Extrusion temperature, melt intrinsic viscosity, feed rate, and the takeup velocity are the key variables for PET melt spinning, as they strongly affect the freeze line location and the as-spun fiber orientation.

Get full access to this article

View all access options for this article.

References

Gagon, D.K. , and Denn, M.M. , Computer Simulation of Steady Polymer Melt Spinning, Polym. Eng. Sci. 21, 844-853 (1981).

George, H.H. , Model of Steady State Spinning at Intermediate Takeup Speeds, paper presented at second joint meeting of U.S. and Japanese Rheological Societies, Kona, Hawaii, April 1979.

George, H.H. , Model of Steady State Melt Spinning at Intermediate Take-up Speeds, Polym. Eng. Sci. 22, 292-299 (1982).

Gregory, D.R. , Rheological Properties of Molten Poly(ethylene Terephthalate), J. Appl. Polym. Sci. 16, 1479-1487 (1972).

Hamana, I. , Matsui, M. , and Kato S. , Filament Formation in Melt Spinning, Melliand Textilber 50, 382-388, 499-503 (1969).

Ishibashi, T. , Aoki, K. , and Ishii, T. , Studies on Melt Spinning of Nylon 6, I: Cooling and Deformation Behavior and Orientation of Nylon 6 Threadline, J. Appl. Polym. Sci. 14, 1597-1613 (1970 ).

Kase, S. , and Matsuo, T. , Studies on Melt Spinning I, J. Polym. Sci. A3, 2541-2554 (1965).

Kase, S. , and Matsuo, T. , Studies on Melt Spinning II, J. Appl. Polym. Sci. 11, 251-287 (1967).

Nadella, H.P. , Henson, H.M. , Spruiell , J.E. , and White, J.L. , Melt Spinning of Isotactic Polypropylene: Structure Development and Relationship to Mechanical Properties, J. Appl. Polym. Sci. 21, 3003-3022 (1977 ).

10.

Nadkami, V. M., private communication.

11.

Oda, K. , White, J.L. , and Clark, E.S. , Influence of Melt Deformation History on Orientation in Vitrified Polymers , Polym. Eng. Sci. 18, 53-59 (1978).

12.

Pajgrt, O. , and Reichstadter, B. , Processing of Polyester Fibres, Elsevier Scientific Publishing Co., Amsterdam, 1979.

13.

Prastaro, A. , and Parrini, P. , A Mathematical Model for Spinning Molten Polymers, Textile Res. J. 45, 118-127 ( 1975).

14.

Yasuda, H. , Ishihara, H. , and Yanagawa, H. , Computer Simulation of Melt Spinning and Its Application to the Actual Process , Sen-I Gakkaishi 34, 20-27 (1978).

15.

Yasuda, H. , Sugiyama, M. , and Yanagawa, H. , Simulation of the Orientation and Its Distribution across a Filament using the Steady-State Single Filament Melt Spinning Theory, Sen-I Gakkaishi 35, 370-375 (1979).

16.

Ziabicki, A. , and Kedzierska, K. , Studies on Orientation Phenomena by Fiber Formation from Polymer Melts, IV: Effect of Molecular Structure on Orientation, Polyethylene and Polystyrene, J. Appl. Polym. Sci. 6, 361-367 (1962).

17.

Ziabicki, A. , and Kedzierska, K. , Studies on Orientation Phenomena by Fiber Formation from Polymer Melts, III: Effect of Structure on Orientation, Condensation Polymers, J. Appl. Polym. Sci. 6, 111-119 (1962).