Effect of Process and Machine Parameters on Changes in Tensile Properties of Threads during High-speed Industrial Sewing

Abstract

The dynamic, thermal, bending and abrasive loading of thread during sewing process has a negative influence on the properties of sewing threads. In this study, the individual and interactive effect of the number of fabric layers, stitch density and needle size on the loss in tenacity, breaking elongation and initial modulus of four types of thread has been studied using Box-Behnken design. Response surface regression equations of loss in tensile properties on the above parameters were developed. The predicted equations agreed well with the experimental data. Contrary to the general expectation, the loss in tenacity and breaking elongation was found to decrease initially or remain unchanged as the number of fabric layers increased. Initial modulus loss decreased with the increase in number of fabric layers for all threads. Except for cotton thread, stitch density did not show any significant influence on tenacity and breaking elongation loss. As the needle size increased, the loss in tenacity and breaking elongation increased for all polyester threads, whereas these properties remained unchanged for cotton thread. Analysis of variance was carried out to find out the contribution of parameters in loss in tensile properties. The number of fabric layers was found to have the highest contribution on tenacity and breaking elongation loss of cotton threads, whereas needle size contributed substantially to the loss in these properties of polyester threads.

Keywords

Box-Behnken design breaking elongation initial modulus needle size number of fabric layers stitch density tenacity

Get full access to this article

View all access options for this article.

References

Ukponmwan, J.O. , Mukhopadhyay, A. , and Chaterjee, K.N. , Sewing Threads, Textile Prog. 30(3/4), 1-94 (2000).

Crow, R.H. , and Chamberlain, N.H. , "The Performance of Sewing Threads in Industrial Sewing Machines," Clothing Institute Technological Report No. 21, The Clothing Institute , London, England (1969).

Gersak, J. , and Knez, B. , Reduction in Thread Strength as a Cause of Loading in the Sewing Process, Int. J. Cloth. Sci. Technol. 3(4), 6-12 ( 1991).

Sundaresan, G. , Hari, P.K. , and Salhotra , K.R. , Strength Reduction in Sewing Threads during High Speed Sewing in an Industrial Lockstitch Machine: Part I: Mechanism of Thread Strength Reduction, Int. J. Cloth. Sci. Technol. 9(5), 334-335 (1997).

Sundaresan, G. , Salhotra, K.R. , and Hari, P.K. , Strength Reduction in Sewing Threads during High Speed Sewing in Industrial Lockstitch Machine: Part II: Effect of Thread and Fabric Properties, Int. J. Cloth. Sci. Technol. 10(1), 64-79 (1998).

Rudolf, A. , and Gersak, J. , Influence of Twist on Alterations in Fibers’ Mechanical Properties, Textile Res. J. 76(2), 134-144 ( 2006).

Midha, V.K. , Chatopadhyay, R. , Kothari, V.K. , and Mukhopadhyay, A. , Studies on the Changes in Tensile Properties of Sewing Thread at Different Sewing Stages, Textile Res. J. (2009).

Rudolf, A. , Gersak, J. , Ujhelyiova, A. , and Smole, M.S. , Study of PES Sewing Thread Properties, Fibers Polym. 8(2), 212-217 (2007).

Dorkin, C.M.C. , and Chamberlain, N.H. , "The Facts About Needle Heating," Clothing Institute Technological Report No. 13, The Clothing Institute, London , England (1963).

10.

Howard, G.M. , Sheehan, J.J. , Mack, E.R. , and Virgilio , D.R. , Sewing Needle Temperature : Part II: the Effects of Needle Characteristics, Textile Res. J. 41(3), 231-238 (1971).

11.

Hurt, F.N. , and Tyler, D.J. , "An Investigation of Needle Heating and Associated Problems in Machine Sewing-I," HATRA Reseach Report No. 19, Hatra Research Centre for Knitting, Dyeing and Making-up , Nottingham, England (1971).

12.

Hurt, F.N. , and Tyler, D.J. , "An Investigation of Needle Heating and Associated Problems in Machine Sewing-III," HATRA Research Report No. 21, Hatra Research Centre for Knitting, Dyeing and Making-up , Nottingham, England (1972).

13.

Khan, R.A. , Hersh, S.P. , and Grady, P.L. , Simulation of Needle-fabric Interactions in Sewing Operations, Textile Res. J. 40(6), 489-498 ( 1970).

14.

Li, Q. , Liasi, E. , Simon, D. , and Du, R. , A Study on the Needle Heating in Heavy Industrial Sewing-Part 2: Finite Element Analysis and Experimental Verification, Int. J. Cloth. Sci. Technol. 13(5), 351-367 (2001).

15.

Liasi, E. , Du, R. , Simon, D. , Dimitrejevic, J.B. , and Liburdi, F. , Heating of an Industrial Sewing Machine Needle, Int. J. Cloth. Sci. Technol. 11(5), 300-314 ( 1999).

16.

Poppenwimmer, K. , Sewing Damage to Knits: How Finishers Can Help Prevent It, Am. Dyestuff Reporter 70(4), 24-29 (1981).

17.

Wu, C.F.J. , and Hamada, M. , "Experiments - Planning, Analysis and Parameter Optimization," John Wiley & Sons, New York, USA, pp. 417-420 (2000).

18.

Myers, R.H. , and Montgomery, D.C. , "Response Surface Methodology," John Wiley & Sons, New York, USA, pp. 343- 347 (2002).

19.

Mahar, T.J. , Ajiki, I. , and Postle, R. , Fabric Mechanical and Physical Properties Relevant to Clothing Manufacture, Int. J. Cloth. Sci. Technol . 1(3), 6-13 (1989).